No video
Toyota Sienna Power Steering Pump Replacement
Рет қаралды 14,373
Күн бұрынVery Bad Leaking Steering Pump And Stuck Pulley Step By Step Job
@mikepeters2130 7 ай бұрын
This was hugely helpful in replacing the pump on my '05 Highlander 3.3L. Great information, fantastic descriptions, excellent angles, and wonderful editing! Thank you!
@JM-AUTO 7 ай бұрын
glad it was helpful and thnks for your time taken on the channel, hopefully you come back.
@kevinconnors4573 3 ай бұрын
Most amazing KZfaq mechanic I’ve ever seen indept explained everything with bolt size
@JM-AUTO 3 ай бұрын
thank you very appreciated comment.
@jeremyetier8203 4 ай бұрын
Would any other component in the power steering system cause the steering wheel to pulsate and grab and the belt to squeak? I’f it’s just the pump, I can follow your directions and get that done. An absolute blessing you are for doing this.
@JM-AUTO 4 ай бұрын
the pump can do that but also the steering rack when is going bad, the squeaking could be the pump or a worn out belt. thanks for sharing.
@rubengonzalez803 11 ай бұрын
Excelente trabajo ! Una pregunta tengo una Toyota sienna 2008 y le cambiaron la Power steering pum y el volante cuesta mucho trabajo para girar la llanta y hace un ruido en la parte de la pieza que cambiaron alguna recomendación se lo agradecería !
@JM-AUTO 11 ай бұрын
ola Amigo y gracias por compartir, si esta duro d girar solo puden ser 2 cosas la bomba o la cremallera pero si usted sebe como estaba el vehiculo antes entoces dece cuenta si tiene una diferencia comparado con antes, tambien desairarla bien.
@rubengonzalez803 11 ай бұрын
@@JM-AUTO la bomba ya fue remplazada y el problema fue que que puso más duro el volante que como estaba antes la segunda opción sería la cremallera cómo comentas ? Gracias por tu ayuda
@jeffw8746 17 күн бұрын
I'm wondering if anyone else has had difficulty attaching the pressurized hose to the pump during installation. The pressurized hose is stiff and about 5" inches too long. If you install the pump first, you can't line up the banjo bolt to go into the threaded hole squarely. If you install the pressurized hose/banjo bolt first before mounting the pump, you can't get the pump to stay in place while trying to screw the 12mm bolt in above the pump and barely can get it to hook and hang. Any advice is appreciated... I've been at this about 12 hours now because of this.
@JM-AUTO 17 күн бұрын
install only the psp it self then the lines, if you got after market high pressure line then it is very hard to line it up n get it to fit, I had the issue in the past, if this is not your case then the best thing to do is to disconnect the pressure line from the steering rack so you can play with it n it makes it easy to fit but doing this is not funny either, if this is not your case either you might be doing some thing wrong, best of lack n hope you find a solution soon
@johnnywood8082 11 ай бұрын
Great job!
@JM-AUTO 11 ай бұрын
Thanks for the visit again and for your time as always, all of my appreciation for your time here, thanks again.
@Speckled_Butterfly7206 6 ай бұрын
So, question how long does this process normally take someone to complete with no extra problems?
@JM-AUTO 6 ай бұрын
2 or 3 hours, thanks for sharing
Project Fix-It
Рет қаралды 96 М.
Fix It Angel
Рет қаралды 486 М.
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 313 М.