BIG SHIP STERN TUBE AFT SEAL - INSTALLATION AT OMAN DRYDOCK -

No video

BIG SHIP STERN TUBE AFT SEAL - INSTALLATION AT OMAN DRYDOCK -

Рет қаралды 16,195

Күн бұрын

A stern tube with bearings radially supports the propeller shaft from the main engine. The stern tube is a hollow tube which accommodates the bearings, the seal boxes and the propeller shaft.
The stern tube is filled with oil, grease or water and forms a barrier between the water outside and the engine room inside the vessel.
The main advantages of stern tube aft seal’ are:
Short built-in lengths due to integrated guard.
Very good protection of the propeller shaft system against sand, debris, (sea)water, etc.
Aft seal is applicable within oil lubricated, grease lubricated and closed - l
CLASS type approved.

Пікірлер: 39

@abdulkhakiqkrishnan3235 2 жыл бұрын

Chief Joel - That was me in the video, thank you, Hope you can visit us again here in Oman Drydock.

@aieshazuleyma8563 2 жыл бұрын

That was huge, so happened to glimpse also on the propeller below it was so big, your job chief is really complex and interesting.

@samirmalik2676 2 жыл бұрын

Wow thanks for including us on your video - hope to spread knowledge in Marine Engineering

@quantumstorm4531 2 жыл бұрын

There is no such regular hours of work in your Job men! Keep uploading interesting video with regards to Ship

@arnulfosumawekwek Жыл бұрын

Seafarers is jack of all trade and regular hours is always broken.

@asiaruby4167 Жыл бұрын

Learning a few about ship parts with your upload

@ashleyjeon3873 Жыл бұрын

Learning so much with your videos with regard to ship

@hassimabdulah5993 2 жыл бұрын

Hi Chief that is our team taking care of your Ship

@uwekpalasak8893 Жыл бұрын

First time to saw stern tube seal being installed

@exceedmanpowerservices6537 2 жыл бұрын

Thank you for sharing

@tomahawkhans1686 Жыл бұрын

The wonder of engineering with this special sealed.

@mayumisibulo1772 Жыл бұрын

Good info

@1mw4tch1ng Жыл бұрын

I know they are professionals but sliding the outer seal of the main ship bore shaft on the prop shaft can be nicked and scratch. any seals installed between the damage shaft 5:22 can fail and leak. While hammering the out seal in place for nut insertion the hammer can accidentally hit the prop shaft and damage

@kristen7378 Жыл бұрын

Your ads are amazing

@xavierusgamilde Жыл бұрын

Interesting

@aliyousof5791 Жыл бұрын

This is really good Chief

@JollibeeMcDonald Жыл бұрын

This is very interesting job, engineering at its best.

@luzzcess7358 Жыл бұрын

Really amazing how seafarer conduct their job

@arnulfosumawekwek Жыл бұрын

Interesting job you have

@dodongdakotv689 Жыл бұрын

Thanks for sharing your knowledge sir.👏

@andrekasim6461 5 ай бұрын

Good job bro

@jobsseaman477 Жыл бұрын

Wow, so that is how it's assembled.

@mayumisibulo1772 2 жыл бұрын

Woah!

@ChrisvinTambatoy Жыл бұрын

Good information mate

@KCdelicaciesLacsib 2 жыл бұрын

Keep posting.

@SherlilouAlbandonate Жыл бұрын

Good job guys

@woodypioneer Жыл бұрын

Very informative

@jackstewart417 3 ай бұрын

This video does not show the engineers replacing or putting in the new Seal Material. It just shows them pushing the Seal housing up to the shaft housing.