This Gauge EVERY G35 Owner NEEDS!!
Рет қаралды 28,708
3 жыл бұрынThis Gauge EVERY G35 Owner NEEDS!! In this video we install a Glowshift oil pressure and oil temperature gauge on the g35! Extremely useful to know what temps are for the oil and make sure you're not overheating your vq35! G35 gauges are a must!
My car is a 2004 G35 Coupe 6MT Brembo Package Desert Platinum and has Muffler Delete exhaust
Follow my instagram at @thejoevazquez
SUBSCRIBE FOR MORE G35 VIDEOS! kzfaq.info?sub_...
WATCH THE PREVIOUS G35 VIDEO! www.youtube.com/watch?v=RJnO3...
Mod List:
Motordyne 5/16 plenum spacer
Motordyne mrev2 lower plenum
BC Racing True Rear Coilovers
Spec D Led Headlights
Nismo Z tube with JWT Pop charger intake
CZP 3.5" Aluminum Driveshaft w/ Foam Noise Dampening
Dasaita 10.2 inch Large Screen Double Din Android
Oil catch can
Custom Cutout exhaust
06-07 Updated Tailights
Hotchkis Adjustable Stabilizer Sway Bars
Roof wrapped in aAvery gloss black wrap
Idler pulley delete
19" Forged Rays wheels
Reverse camera installation
redline custom steering wheel wrap
coolant bypass valve
energy polyurethane front upper control arm bushings
simplistic garage 75mm big bore throttle body kit
noico sound deadening on trunk, rear seats, and doors
z1 stainless steel brake
z1 brake master cylinder brace
370z Nismo 3.916 rear differential with nismo differential cover
z1 motorsports differential bushings
Check out my podcast! Chip & Joe Show: kzfaq.info/love/jBy...
Recently uploaded, Fifth Generation Nissan Z-car (Z33) Every G35 NEEDS This! Installing BOOST Gauges in my Infiniti G35 Coupe! DIY G35/350Z AMAZING ADD W1 3D CLUSTER GAUGES NEW GAUGES + Pillar Pod Install!! GlowShift | How To Install A Gauge Pillar Pod New Wheel Color For My G35! Do Glowshift Gauges Review after 3 years of use! Preparing the G35 for Boost ( Gauges )
Infiniti G Joe Vazquez g35 coupe mods g35 mods g35 muffler delete infiniti g35 infiniti g35 coupe 2004 infiniti g35 coupe g35 headlights g35 tail lights infiniti g35 muffler delete G35 Coupe Tricks - Key FOB and Interior Tricks Small Upgrade EVERY G35 Owner NEEDS!! G35 How to Program Key Fob!! Top 3 G35 Mods EVERY Owner NEEDS! How to program a Infiniti G35 remote key fob 2003 - 2006 HOW TO PROGRAM G35 KEYLESS REMOTE * G35-Top PERFORMANCE MODS* Installing My Spec D Headlights On My G35!! How to program Infiniti Keyless Entry Remote Keyfob Replacement Programming
@wadesmith1135 3 жыл бұрын
Can you leave links for all the parts you’re putting on. I’m looking for most of the parts and can’t find them. Probably doesn’t help I’m in Canada Thanks
@gavin_p8582 3 жыл бұрын
Picked up my first g35 a week ago, love the channel!!!
@JoeVazquez 3 жыл бұрын
Hell yeah bro, I appreciate it that honestly!
@marlonmcderby5058 3 жыл бұрын
Cleanest G35 I’ve seen 💪🏽 Keep going 👍🏽
@JoeVazquez 3 жыл бұрын
Haha I appreciate that bro ✊
@andrewwhitfield5366 3 жыл бұрын
That’s crazy I just did all this the glow shift kit is sick! Nice video!
@JoeVazquez 3 жыл бұрын
It was honestly very easy to install!
@pieroruiz9154 Жыл бұрын
fan of the build
@JoeVazquez 3 жыл бұрын
Thanks for watching guys!! Let me know if you guys have any questions!!
@matsgarageandstuff 3 жыл бұрын
I deff like the add ons you do on the g35. I'm rocking a 03 sedan with headers beluga down pips 5/8th spacer but mine needs tuned
@JoeVazquez 3 жыл бұрын
Same here! I need to tune mine but I’m waiting for smog so I can install test pipes on the g!
@DollFaceox 3 жыл бұрын
I have a 04 g35 sedan. I’ve been trying to find the clear side markers for the LONGEST!!! It’s easy to find if for the coupe… Do you have any ideas where I can find it for the sedan?
@gemargordon6885 2 жыл бұрын
You ever figure out what fuse to use for orange dimming with the headlights ?
@BeDistinct 3 жыл бұрын
Oooofff it looks super good bro! 😫
@JoeVazquez 3 жыл бұрын
Thanks big zaddy! 🥴
@davidklein99 3 жыл бұрын
Am I the only one that thinks its dope you two support each-other? More G dudes should be like this!
@bautistavazquez6295 3 жыл бұрын
This is definitely next on my g sedan did my 4th drift event and Temps where getting up there since it was a private day tons of driving and tandems had to cool the car off on occasion so cooler and temp gauge is next
@JoeVazquez 3 жыл бұрын
Definitely man!
@synaptik111 6 ай бұрын
Hey Joe - can you go into a little detail about the actual route you took from the sensors through the engine bay into the cabin? Did you have to extend any of the cables? And if so what were the wire gauges and the new lengths approximately? Thanks!
@doohyunyun7224 2 жыл бұрын
Hey Joe! I'm planning to install same gauges as yours on my G. Where exactly tap your expandable circuit for dim function on fuse box? Thank you!
@_venomg35 Жыл бұрын
Hey, I love your videos. I have a 2006 g35 coupe MT. I have a oil pressure and a oil temp gauge. With one wire temp sensor. Can I splice the temp gauge into the same single wire coming from connection at engine. Thank you
@Beliefacy 3 жыл бұрын
You really getting into some meat and potatoes with the performance side of your ride bro! SICK!
@JoeVazquez 3 жыл бұрын
Thanks man, let’s goooo!!!!
@thewrapgod6221 8 ай бұрын
It’s not over kill for a daily at all your just one of the few proper g owners haha
@JoeVazquez 8 ай бұрын
I appreciate it brotha!!
@willieclark6967 Жыл бұрын
Is the sandwich adapter plate a good location to get oil pressure if you have an oil cooler ?
@nateskicks6995 2 жыл бұрын
I plan on doing this for my car where did you get your sandwich plate from?
@sergiojimenez5399 3 жыл бұрын
Lettttttttssss gooo Joe!!
@JoeVazquez 3 жыл бұрын
Letttsssss gooooo!!!!! 🙏
@jasonredepenning 3 жыл бұрын
Oh man there are so many factory holes you could have gone through. I'm sorry for your cancer starting hole. I had a different G35 and I left it sit one summer on gravel and I've never seen a car rust so bad. Prep and seal that well.
@JoeVazquez 3 жыл бұрын
Yeah it’s good to go, thank you for checking up!! 🙏
@pieroruiz9154 Жыл бұрын
what is the oil cooler sandwhich plate you used???
@gustavomeza6853 2 жыл бұрын
@Joe Vazquez What kind of oil pressure readings are you getting. I just installed an AEM oil pressure gauge and I’m not sure if my readings are correct. What’s readings do you get at cold start? Warm idle? Wide open throttle?
@willrise3980 2 жыл бұрын
hey joe , do u have the place where u bought the gauge holder pls, thank u
@Foxxninja 3 жыл бұрын
Thumbnail=nice. Cuz you know, the number.
@JoeVazquez 3 жыл бұрын
Hahaha 😂😂
@brynwilliams6770 3 жыл бұрын
Congratulations
@JoeVazquez 3 жыл бұрын
Thank you!
@letsgetlifting6793 3 жыл бұрын
Why is it important to know those two numbers? I know you don’t want your oil too hot. Also what numbers are considered a safe range and what numbers should you be worried about?
@Airborne1409 2 жыл бұрын
The pressure gauge is to monitor if you are prone to leaky oil like the gs are known for.
@noahcook6608 3 жыл бұрын
Where did you get the Gauge pod?
@Kris6oh 3 жыл бұрын
What’s oem oil pressure supposed to be at ?
@jessye.9828 2 жыл бұрын
Where did you get those parts from bro?
@luismendoza-eu7qx 2 жыл бұрын
What samwhich plate is that
@madmarlone 2 жыл бұрын
Just wondering what brand are your sway bars cuz mine came with red sway bars front and rear
@JoeVazquez 2 жыл бұрын
Mine are hotchkis sway bars! I know stillen sway bars are also red! Either way I’m sure you have good branded sway bars!
@chrisyo295 7 ай бұрын
Where did you order yours at??
@DennyBalance 3 жыл бұрын
Still need to do this lol
@JoeVazquez 3 жыл бұрын
Do it!! Definitely pleasing to see!
@captainzz4723 3 жыл бұрын
Awesome work Man! Just 2 things (not hating or anything) 1) At 02:45 I noticed some oil drip, direction looks like it came from the sandwich plate. Not hating at all or anything just wanted you to check so you don't lose oil slowly (if you removed some stuff before which caused the drip all good). 2) I have a V35 Skyline but I'm 99% this next part relates to you. If you need to bring in wires in the future, there is a rubber grommet above the accelerator/brake pedal etc which you can slide a coat hanger through. You can then loop the wire you need and pull it through. Saves you drilling in the future. Again not hating or anything just wanted to mention it. 🙂 Keep up the amazing work! Repping the VQ Gang well ❤️🙌👍
@JoeVazquez 3 жыл бұрын
IM PISSED YOU COMMENTED THIS HATERR!! Haha I’m messing with you bro! Thanks for your honest feedback! 1) I do have a leak where the sandwich plate meets with the stock oil cooler, Very slow leak so I’ll postpone that until I do an oil change to get in there! 2) I noticed it but I don’t really know why I didn’t go ahead and try it from there! Again really appreciate looking out and this can help anyone else that plans on doing this to their g35 skyline!
@captainzz4723 3 жыл бұрын
@@JoeVazquez Haha my phone notification just had your first sentence pop up and I was like oh oh 😅 That's good to hear you're on top of things! Can't wait for the next video drop! 🙌
@JoeVazquez 3 жыл бұрын
Hahaha I gave you a scare there! 😂 I appreciate your support man foreal, thanks for watching!! 🙏
@captainzz4723 3 жыл бұрын
@@JoeVazquez Haha the Man! Also forgot to write in my comment, where you drilled through, will you add a rubber grommet or rubber seal? It's not necessarily going to get a huge amount of water or anything, just for general moisture/debris sealing and also reduce the wires from rubbing and cutting on metal etc. 🙂
@JoeVazquez 3 жыл бұрын
I didn’t have a grommet so I put electrical tape around the drilled hole for now until then! Good observation!
@davidherrera8406 3 жыл бұрын
Where did you get the sandwich plates for the oil cooler
@JoeVazquez 3 жыл бұрын
I bought it with the oil cooler kit but I’m sure you could even find it on Amazon!
@Trafican_sanchez Жыл бұрын
Is there any for the gas gauge
@marlonmcderby5058 3 жыл бұрын
I have a quick question i have a 2009 G 37x coupe and i want to put a nismo radiator cap on the radiator but I’ve heard it could cause problems like putting extra stress on the coolant system cause it’s designed for modded vehicles i just want it for looks 😂 what do you think????? Thanks
@JoeVazquez 3 жыл бұрын
The nismo radiator cap makes the boiling point higher, and will add more stress in the cooling system, I’ve heard a lot of people will get a crack on their radiator from the plastic parts of it from that added stress!
@JoeVazquez 3 жыл бұрын
If you want it, just get it but just keep that in mind! I’m upgrading my cooling system and will eventually get a nismo or z1 radiator cap!
@andrewwhitfield5366 3 жыл бұрын
How has your oil cooler been holding up? I just installed my g plus kit with thermostat about a week ago. So far so good!
@JoeVazquez 3 жыл бұрын
It’s been doing great, I check up on it frequently to make sure everything is good and I have no leaks, I have a tiny leak where the sandwich plate mates up to the factory oil cooler but nothing to worry about! Very happy with the product and the price
@miragevictor9316 3 жыл бұрын
Did you figure out how to dim it? i have a g35 and was curious aswell. Thank you.
@JoeVazquez 3 жыл бұрын
I would just have to tap into something that has dimming function
@doohyunyun7224 2 жыл бұрын
@@JoeVazquez hey Joe I'm planning to install same gauge of yours on my G Where exactly tap your expandable circuit amp fuse cable on fuse box for dim function? Thanks!
@6.4scat36 3 жыл бұрын
Do you have the link for the A pillar gauge piece
@JoeVazquez 3 жыл бұрын
Yeah bro I got you! www.autometer.com/2-1-16-triple-pillar-infiniti-g35-02-05.html
@theg35project50 2 жыл бұрын
How much you think you have spent in after market parts/mods you have put on? Mine is stock and will be doing some videos of my build. Would love some support 🙏🙏🙏
@JoeVazquez 2 жыл бұрын
Too much money, around 20k and it still looks stock haha 😂
@jamestapia9057 2 жыл бұрын
Link ?
@phillipenoe 3 жыл бұрын
10:02 nice meme👌
@artOfkisS 2 жыл бұрын
is this Pillar you are using a version for the 350Z?
@JoeVazquez 2 жыл бұрын
It’s g35 coupe specific
@Mjm635876 3 жыл бұрын
can we get a link for the gauge plz
@JoeVazquez 3 жыл бұрын
www.glowshiftdirect.com/10-color-digital-dual-temperature-pressure-gauge/
@bryynx 3 жыл бұрын
Can it open from the back cuz im finna get it and change the light color
@JoeVazquez 3 жыл бұрын
There’s a button to change it to 7 different colors
@bryynx 3 жыл бұрын
@@JoeVazquez ik but i was thinking bout having it like multiple colors by dividing it in the inside if possible but I'm just finna buy it either way
@JoeVazquez 3 жыл бұрын
Ohhh I see what you mean!
@v36vhr 2 жыл бұрын
So what's your oil pressure???
@gavin_p8582 3 жыл бұрын
BOOSSSSTTT
@JoeVazquez 3 жыл бұрын
Exactly!!
@gordonsweep 3 жыл бұрын
Hey there… do you know if this will fit on a 2006 Infiniti FX35 ????
@DennyBalance 3 жыл бұрын
Yes
@gordonsweep 3 жыл бұрын
@@DennyBalance hey thanks.. one more thing... can you send me the link for the parts you use for the install ??? I want to do the same
@JoeVazquez 3 жыл бұрын
This is for the gauge pillar I bought! www.autometer.com/2-1-16-triple-pillar-infiniti-g35-02-05.html And this is the gauge that I got www.glowshiftdirect.com/10-color-digital-dual-temperature-pressure-gauge/
@gordonsweep 3 жыл бұрын
@@JoeVazquez hey.. thanks for the quick reply
@JoeVazquez 3 жыл бұрын
You got it brotha!
@SME4GY 3 жыл бұрын
Boost 🤔
@JoeVazquez 3 жыл бұрын
Hmmmmm 👀
@cesardaniel8690 3 жыл бұрын
Make a subwoofer install tutorial please
@JoeVazquez 3 жыл бұрын
I’ve been thinking about that, I may have an idea for a very low key one!
@matsgarageandstuff 3 жыл бұрын
Looks like you're oil cooler housing is leaking may have pinched the new seal or old seal get that fixed that's an oil pressure loss
@JoeVazquez 3 жыл бұрын
Thanks for commenting that bro! It’s a very small leak but I will definitely be taking care of that, I believe the new seal might be pinched and readjusted or I just need to torque it down a bit more!
@matsgarageandstuff 3 жыл бұрын
@@JoeVazquez I've had alot of trouble with thoughs seals in the past it's best to get have the car jacked up so you can see all the way around that oil cooler housing where the seal meats the engine and thread that housing bolt by hand until you gotten it snug by hand then torque to spec .also some good engine grease to hold the seal in place. Make sure you get an oem nissan gasket don't trust that cheap shit and It'll be leak free for years
@matsgarageandstuff 3 жыл бұрын
@@JoeVazquez I've got 3 g35s rn one drifter and one daily and one Parts car all sedans
@JoeVazquez 3 жыл бұрын
Noted! Thanks again for reaching out bro, I appreciate it seriously!
@matsgarageandstuff 3 жыл бұрын
@@JoeVazquez no problem man I'm trying to get going on content as well I'm up in Oregon and nobody has good G35 content out this way and plus if I wanna tune I gotta travel to Seattle or south Cali for a tune on the Dino
@armaleyvaten 3 жыл бұрын
cool vid, but both are pointless (unless FI).Oil pressure is cool but its not gonna save u, cause a red oil comes on when oil pressure is below the adequate amount. Oil temp only if u are tracking the car and that's already like under 4% of g35 drivers in the states (drift not included). These are useless and a waste to the typical g35 owner. A gauge that would be useful is a coolant temp gauge, because that directly correlates to any overheating, in fact the factory temp gauge tells you nothing until its a lil too late- it just sits at the mid way point, but by running a coolant temp gauge and knowing ur usual operating temp, u can watch ur coolant temp on a hot day and cool the car down(ie turning off ac, turning heat on high, pulling over before u blow/damage anything. But cool install vid, it makes it easy for a beginner to install.
@JoeVazquez 3 жыл бұрын
This is a daily driver/track build 😂 I’m also installing coolant temp gauge with an upgraded radiator! I also make these mod videos for content brotha!!
@JoeVazquez 3 жыл бұрын
Oh and these mods are future proofing for turbo baby!!!!
@armaleyvaten 3 жыл бұрын
@@JoeVazquez yea but u titled it "This Gauge EVERY G35 Owner NEEDS!!"
@invincible201xxx Жыл бұрын
Oil temp gauge is good too for when you drive your car before it's warmed up so you know when you can punch the gas after the oil sits at a normal temperature
@jrserrano9396 3 жыл бұрын
Bro that cover annoying as fuck I threw my shit away lmao
@MichaelR.C 3 жыл бұрын
needs to learn how to properly lift a car
@JoeVazquez 3 жыл бұрын
Youre right, I need to lift it from the bumper next time!
@qpzmak 3 жыл бұрын
@@JoeVazquez lol he is not jk. You are actually denting your car by lifting it from there. If your car is rusted the jack can go threw your car
@JoeVazquez 3 жыл бұрын
it doesn’t look pretty but I’ve been doing this for AGES, even at a dealership level we use pinchwelds to lift cars. It literally says in the Nissan/Infiniti manual that you can lift from the pinchweld, there’s no issue trust me
@MichaelR.C 3 жыл бұрын
@@JoeVazquez but notice how urs is trashed and the people who know what they are doing arent?
@JoeVazquez 3 жыл бұрын
I bought the car preowned and was dealership serviced with dents on it already so that rules it out, and the reason it’ll get more dented is because the jack my buddy has, doesn’t have the rubber padding on it, that’s literally it. It cosmetic, it doesn’t change anything structurally just looks bad but I don’t care 🤷♂️
@Venolin1 2 ай бұрын
Bruh, you really out here drilling holes in your chassis *facepalm*. Hope you coated those with paint or primer to prevent it from rusting. Pretty sure these's existing holes and grommets you could have used. Also, people don't drill holes in their sh!t because they care about their car. It's actually ghetto to drill holes 🤣. Hate guys that do work like this then sell the car to some poor fool.
@JoeVazquez 2 ай бұрын
I’m not selling the car, what are you on about lol. I don’t show every single thing I do on/off camera. I also live in cali brotha, but if you’re hard pressed by someone drilling a hole on their car and selling it to another individual, you’re pressed by the wrong thing LOL.
@hdgoon829 3 жыл бұрын
Why Ghetto
@JoeVazquez 3 жыл бұрын
Ghetto in the sense that it takes so little effort to make it look like a clean install but people cut corners and make it look janky and a rushed job for no good reason
Jason Derulo
Рет қаралды 53 МЛН
Jarrod Willemse
Рет қаралды 388
NODRFT - New Orleans Drifters
Рет қаралды 4,5 М.
AutoVlog
Рет қаралды 10 МЛН
AUTO VRN
Рет қаралды 3,4 МЛН
OYBOY
Рет қаралды 529 М.
cylinder head cracked & leakage checking #amazingtechnique #mechanic #engine #trending #viral #short
Truck Care TV
Рет қаралды 9 МЛН