John Deere X758 3 Point Retro Fit Kit Install

No video

John Deere X758 3 Point Retro Fit Kit Install - Prep for 3 Point Install

Рет қаралды 5,794

2 жыл бұрын

Pretty in depth video on the install of the 3 point hitch "retro fit" kit. This kit is required for some reason on the new x700 series. The kit is part of the 3 point kit, so no need to purchase it separately. This kit and the rockshaft should have just been installed from factory on all tractors for what they cost, and for the nature of this level of tractor.
**DISCLAIMER: THE CONTENT IN THIS VIDEO IS NOT BEING INSTALLED BY A JOHN DEERE TECHNICIAN AND I AM IN NO WAY GUARANTEEING THAT THE INSTALLATION OF EQUIPMENT AS DEPICTED WILL BE COVERED UNDER ANY WARRANTY IN THE EVENT OF FAILURE. I WILL ALSO NOT BE HELD LIABLE FOR ANY DAMAGE OR INJURY TO YOURSELF , OTHERS, OR EQUIPMENT DUE TO THE USE OF THIS CONTENT. THIS VIDEO IS FOR ENTERTAINMENT/IDEA PURPOSES AND SHOULD ONLY BE USED AS REFERENCE AND NOT AS A REPLACEMENT TO ACTUAL TECHNICAL DATA.**
***NEW!!! JGG on Facebook here:
www.facebook.c...
Follow for updates on builds and to see what’s going on!***
**Now you can reach me by email @ joshsgreengarage@outlook.com**
If you have any in depth questions, need to send a picture or video of a problem you are having, or want more info on something you saw me do or make, feel free to send a message!

Пікірлер: 25

@joerizzo5324 4 ай бұрын

I wouldn’t have been able to do it without you. Thank you.

@chadweddle702 6 ай бұрын

Nice video! I’m installing Ron’s H3 kit from aux hydraulic. Removing the linkage rods would have helped a lot for me. I may still remove them to install the hydraulic lines easier. I’m adding a second piston to the mower deck to separate it from the rear 3 point lift. It’s gonna be a sweet set up. The rear will be on its own piston so the linkage bar is deleted.

@billreed79 Жыл бұрын

Just finished installing the retrofit kit on my x758. It wasn’t the most fun thing in the world to do, but the video definitely helped! Thanks! A Little trick I did was to fully tighten the hose end of the 90 degree fitting that connects to the hardline, but leave the hose end of the 90 on the cylinder a little loose. That lets you get everything positioned, and you can snug the hose from the back of the tractor very easily once the hard line is connected.

@1891shooter 2 жыл бұрын

I just bought a hitch kit for this tractor and had no idea how this was done. Thank you for videoing this and hopefully part two is out soon.

@JoshsGreenGarage 2 жыл бұрын

I have the second part recorded, just got to put it together… I’ll try to get it out tonight if you need it!!!

@1891shooter 2 жыл бұрын

@@JoshsGreenGarage Thanks! I’m going to finish it Monday. Appreciate it

@JoshsGreenGarage 2 жыл бұрын

The hitch assembly is up! Hope it helps if you have any issues!

@BobWilson84 2 жыл бұрын

Wow, you were right on the money. Yes, install and tighten the 90 fitting on the cylinder before installing. Yes, the rear lift arm instructions are terrible. YES! why wouldn't Deere install this cylinder in a better spot in the first place! WHY would Deere use a u-bolt in the first place to hold the cylinder against the frame?!?!?! Just so many questions after a really frustrating install. Thanks for your video, it was excellent and helped a lot!

@chadweddle702 6 ай бұрын

I was able to get the pin for the cylinder through the hole on the left frame rail. You don’t have to move the pie shaped brackets.

@BobWilson84 2 жыл бұрын

Thanks for this video! my crows feet only go to 3/4 as well. I'm getting a 13/16 crows foot right now to make this easier!

@BobWilson84 2 жыл бұрын

Reply to myself. I got the crows foot, just waiting on my tractor to show up :)

@mikebracht9261 2 жыл бұрын

Good job, Josh. I went through it a couple years ago. It does have a high suck factor. Lol 😂

@TYPHOON-ox9tm 2 жыл бұрын

Hi , congrats on your new tractor !! Its such a beautiful and capable machine , altho im curious why you havent gone with a 1023e or a 1025r ?

@JoshsGreenGarage 2 жыл бұрын

Just too much for my needs, honestly the X700 series probably is too, but it’s a hobby… I don’t have enough work or projects to justify a 1 series, and I’m not gonna seek out projects just to justify it

@bobjohnson4025 2 жыл бұрын

I bought a X758 recently too. Don't want a 1025 series either as I have a case 580K for doing real dirt work. I also had fun installing my 3 pt hitch too.....Also installed the pto kit and air seat. All fun projects. Your very well done vids are great! Keep em coming!👍

@TYPHOON-ox9tm 2 жыл бұрын

@@JoshsGreenGarage i see , i was juste curious since it was about the same price and it come with the 3 point +you have a 2 range tranny,, but to be honest your x758 is much better looking , even if it intended for work its always nice to have a good looking machine haha

@michealdesantis7067 9 ай бұрын

JOSH any tips on removing the three point hitch

@JoshsGreenGarage 9 ай бұрын

Like completely? Or just the arms? Arms are easy, just pull the pins… whole thing is a different story. Wouldn’t really want to take it all out unless absolutely needed.

@michealdesantis7067 9 ай бұрын

Josh yes completely bought the tractor used and will never use it. i have everything off except for switching the hydro lines back

@JoshsGreenGarage 9 ай бұрын

Probably not going to be able to unless you have the original fittings. I’d just leave it on. It’s a great accessory, one day you may find a use. If you absolutely wanted though, you may have to go to Deeres parts catalog, and find all the fittings on there to revert it back. Cost some money though.

@michealdesantis7067 9 ай бұрын

josh do you know the the part numbers for the - pin - two bushings - cotter pin from the lift cylinder you discard

@JoshsGreenGarage 9 ай бұрын

M90097 (1), M154594 (2), then either 11M7017 (1, serial number ___-010000) or GX21530 (1, serial number 010001-___)