I watched a few videos, said ok, got a good one found. Pump kit came in and I couldn’t find the video I thought I saved. Found yours and it is the best one I found! Pretty much crayons and coloring book, if a guy can’t replace his outboard water pump with your video and directions, he probably should not chew gum and walk! You did an awesome job, sir!
@JShep-yu3ki4 жыл бұрын
Great detail in your video!! Made the replacement of my friend's water pump much easier. Found the old pump wasn't working because the impeller key was missing. Shaft spins, impeller didn't. Quick rebuild (with your assistance) and it works great now. Thanks
@robertswanson31673 ай бұрын
Your Vids have been helpful for my E35ELCIG - 1981 Evinrude 35 hp. I am working on replacing the engine wiring harness as the motor stopped working after a themostat/ water pump replacement. The wiring is all green and cracking. Heck, the joined by orange wires "coils"..... the black single was green also and of course broken. TY
@mattbuchan21252 жыл бұрын
Great video. Woeked perfectly on my 1996 Evinrude 25. Much apprieciated.
@CharlesJCliffe3 жыл бұрын
Just a tip; once you remove the keeper @4:50 you can screw the top nut back into the bottom part by a few threads, and then remove the rod without losing the nut. Can usually do it before un-bolting the lower unit too if you shift it to separate them.
@knoxy604 ай бұрын
Superb video! Very, very helpful and allowed me, for the first time, to replace the water pump. Thanks.
@rlr42944 ай бұрын
am 68 years old run motors all my Life changed many water pumps - i just change the rubber impellor and leave everything else in place ! all that added glue is not at all necessary. but its a great video and my opinion only . lining the water tube is always my problem .
@pjimmbojimmbo19904 жыл бұрын
Dishwashing Liquid or KY Jelly are better choices for Impeller Lube. Petroleum Products have been known to harm the Neoprene used in the Impeller
@eazyrider61222 жыл бұрын
I used assembly lube its good for all rubbers etc and will eventually wash away. I guess some olive or sunflower oil will work as well. Just that i have a big bottle assembly lube is why i used it.
@MikeSmith-mt5zc2 жыл бұрын
ok so I have a 1976 25hp Johnson Seahorse boat motor, the water intake is different its just a single inlet just above the prop area, does that make a difference, I have to use a water hose if I do not have a barrel, Also Do I need to drain the grease from the lower unit first.
@nickbuchanan47565 ай бұрын
Followed you step by step, perfect! Thank you!!
@NorthernANTs3 жыл бұрын
Thank you I just finished the replacement of my water pump, thanks to your video. 1997 Johnson 25
@user-wl2lt2xv6g5 ай бұрын
Hey! What is this enclosed prop lower unit? What years were they made and where can I get one? I have been looking for something like this for years. There are several rocky river runs near me that I've wanted to explore but will only go by canoe or kayak.
@JarvisMcBride2 ай бұрын
your a legend thanks mate awesome work 👍
@owenaquilina5001 Жыл бұрын
after following your steps the motor seems to be highly revved, and it is not the speed throtttle, and ideas what can be the issues please? also is it normal that the water pump is too tight that the blades bend when inserted?
@Jerold-bu3ul21 күн бұрын
Why you need a new housing??
@alejandroguijarro8650 Жыл бұрын
Hello Brandon! Really thanks for the video, i got same model and water haven't still got out, I bought the kit so I hope fix it soon. I have more parts to fix carburettor and propeller, I couldn't find the manual instructions, and in the video you spoke about it, can you tell me where I can find it? Thanks in advance!!
@bwilson16492 жыл бұрын
Very helpful video. Instead of gasket sealing compound on the bolt threads, would anti-seize (typically used by me on spark plugs) also work? It looks like the bolts in the Evinrude kit already have anti seize on them.
@owenaquilina50012 жыл бұрын
Dear what is the purpose of the keeper underneath the linkage gearbox joint. I lost the nylon tapered keeper can I replace it with a small O ring please so the linkage nut will not slip off? Thanks in advance, very informative video
@samtate12603 жыл бұрын
That is strange looking but cool I can see why the military would use it rocks and shallow water I bet it’s built like a tank durable and ready for hard use
@paulfisher829910 ай бұрын
seeing you working on a military Evinrude, I wonder if a manual is available for a 1998 military Evinrude model MAL 35D? If so, please let me know.
@jasonarthur12082 жыл бұрын
Do you still have the long shaft conversion parts (I.e. driveshaft, water tube and housing)? My ‘83 Johnson 35hp is a short shaft and it’s on a Jon boat I think is designed for a long shaft. Thank you for your time. Great video. Learned a lot.
@phillowe33554 жыл бұрын
damn ,mine is the older style,,any links to doing a 1976 25 hp
@danielmcbride48282 жыл бұрын
I have a 62. 28 horse Evinrude and it's actually a lot easier
@mrsuarez430 Жыл бұрын
I have 1978 35 it has a different pump case than the 77 and 79 lol it has 4 screws instead of 6 the plates smaller as well
@trevorhanlon7772 жыл бұрын
Hi, can i changed my 1979 35 hp carburetor. Can you change the carb jet to increase the higher hp? Thankyou
@coupercarpenter27272 жыл бұрын
Did this and my motor still won pee, lines are clear and thermostat is out, what should I do?
@laylow8967 Жыл бұрын
Thanks Brandon 👍
@SaintCronch Жыл бұрын
That through bolt (the one with a nut) is stuck like crazy on my johnson 30hp 1987. Tried WD40 and waiting for hours, wiggling, janking, heated it with a torch and bashed it and tried hammering in wooden shims. It just won't come of that end. Any advice on what else I can do? the other 4 bolts are off and I've separated the shift linkage.
@brianmeyers7755 Жыл бұрын
I’m having the same problem now, did you ever get it done?
@NC_Fisherman1 Жыл бұрын
@@brianmeyers7755 I had the same problem. I wind up taking a fine tool and just cutting it out and beating it off. And just replacing it with a stud and locking it down with a nut.
@sergioperez78642 жыл бұрын
excelente video¡¡¡¡¡
@yajreizarb3 жыл бұрын
Excellent overview! Thanks!
@brandonlum27532 жыл бұрын
Do you have the kit part number? I have a 35 hp evinrude. My motor doesn’t have a plate to find what model it is. I believe its a 1982
@matthewwaldron18033 жыл бұрын
Do you have a link to where you bought this kit from all the kits I find don’t include the black pipe type piece that goes over the gear shaft
@ricardoesquivel56503 жыл бұрын
I want to thank you for this tutorial. I replaced my water pump today, with the help of this video. Is it possible to up the horse power on my 1993 Evinrude 25hp 2 stroke with a simple carb change?
@BrandonsGarage3 жыл бұрын
Carb and manifold. May not be worth the cost though, gains are minimal.
@danielmcbride48282 жыл бұрын
@@BrandonsGarage do you need a gasket for the bottom and when you put it back on
@jaycarrasco39352 жыл бұрын
What do I do if I can't line the water tube back up
@12345scottt4 жыл бұрын
Brandon can I take the new BRP throttle and replace with the old OMC throttle, like the white one in your video.
@snakeguy462 жыл бұрын
Hi Brandon, great video. I followed your your tutorial, and all went well. I did one extra step and removed the two flathead screws to change the oil when I am finished. I also took out a Philips screw next to the bottom flat head to help drain oil. When I reinstalled, I had issues putting the Philips back in and now can't seem to put in in or out of gear? It doesn't matter what I do the unit stays in neutral? What do you think I done wrong?
@rlr42944 ай бұрын
Im not Brandon but that little rubber that holds the shifting shafts together is probably compromised .
@kx85isweet3 жыл бұрын
Hey do you have a video for water pump replacement on early 80s motors?
@trebblej3 жыл бұрын
Should gear oil come out when you pull the driveshaft out?
@dancarnahan49464 жыл бұрын
I did this same job and now the shifter won’t go into reverse. Did you have the same problem? And if so how did you fix it?
@jamescecil37984 жыл бұрын
I’m having the same problem, did you get a reply?
@dancarnahan49464 жыл бұрын
@@jamescecil3798 No I didn't. But I ended up shifting the lower shift rod into the reverse position by hand and then connecting the shifting rod together and it worked much better. You may have to turn the prop by hand while trying to get the lower shift rod into the reverse position. Not perfect yet, but workable. I also noticed the shifter in the motor housing was rubbing against the fuel line that wasn't helping the problem either.
@jamescecil37984 жыл бұрын
@@dancarnahan4946 I just talked to my mechanic, he told me to turn the lower unit shift rod down or all the way tight. I'll give it a try after work today.
@davekimbler23084 жыл бұрын
So now it’s a Shorty ! Lol. Was that a salty ? The reason I’m asking is the anode looks a bit smaller . Is the 1300 lube like red tacky ?
@mnorth282 жыл бұрын
Fantastic helped me no end 😊
@ddemon4406 Жыл бұрын
I've been leery of buying OMC rubber gaskets and o-rings since they've been sitting on shelves for years at this point. I've had one "new" o-ring out the box broke even with careful handling. Anyone else experience this?
@BrandonsGarage Жыл бұрын
If you're buying it on eBay, and/or in comes in one of the tan 'OMC' boxes, I would avoid it. Otherwise, BRP is still manufacturing parts. Fear not about buying most OEM stuff.
@larryweldon296411 ай бұрын
My 95 25 hp Evinrude outboard doesn't have the linkage like that
@marycarmenurbinadegonzalez2632 жыл бұрын
Cómo puedo reparar un sigueñal
@brianmclain304510 ай бұрын
13:17 I appreciate the video for sure but… there are several points(which I thought to be pretty important) wherein you completed the step off camera! Otherwise it was a big help thank you
@westoniii8 ай бұрын
Leave shift linkage in N. For the whole process.
@Michaelmsneed11 ай бұрын
I wish you would of shown the propeller key.
@DougsMessyGarage4 жыл бұрын
This video makes me want to dust off the 1971 18hp Evenrude my father has in his junk pile. That old machine has caught a lot of fish in its day. It's last regular use was by me in the early 90's and it had the annoying problem of popping out of gear. It moved a 14 ft skiff along pretty well when it still ran properly.
@davekimbler23084 жыл бұрын
Your clutch dog might be worn .
@yoursuccess11 ай бұрын
the piece you slid over drive shaft on to on top of water pump housing, is that required? I did not have that on my 71 Johnson long shaft? also no gaskets.
@BrandonsGarage11 ай бұрын
Pretty sure they had them, too. And yeah, I'm pretty sure they are required. Keeps exhaust gasses from entering the pump.
@andrewburger75614 жыл бұрын
What’s the purpose of that black water tube on the drive shaft?
@israelalcantar87652 жыл бұрын
It can fit on mine 1973 evinrude 18hp?
@IBFISHING8133 жыл бұрын
I'm having trouble with my key o don't know how to install it
@user-mi1th1fl2j5 ай бұрын
Hello is this the same procedure for a 1995 50HP Evinrude?
@BrandonsGarage5 ай бұрын
Nope, watch my 40 HP videos for that one.
@user-mi1th1fl2j5 ай бұрын
Brandon seems my model 50hp/e50tleod evinrude has the bolts at the bottom like in this video.
@jrussell4711 Жыл бұрын
Damn cool! Great vid.
@user-ht4qg6og3e2 жыл бұрын
A full water pump, how much is the price, please? My friend
@phillowe33554 жыл бұрын
Id love to get the lower end unit for my 25,,
@timmypugh38503 жыл бұрын
What are the 2 black rubber rings for ?
@lawrenceflynn8245 Жыл бұрын
That is what we missed Lost me also at that point and wanted to quit
@user-us5om7wd3g2 жыл бұрын
Very good video..... Thanks!!!!!
@kenhilson7863 жыл бұрын
I see a water tube being installed on the drive shaft near the end but I never saw it on the shaft when he lowered the gear box.
@danielmcbride48282 жыл бұрын
The water tree was still stuck in the top end of the motor when they pulled the lower-end off
@Matt.Hemple Жыл бұрын
thanks for the video
@jonahporter98263 жыл бұрын
Can you post all the lubes and sealer that you used throughout the process, thanks
@timothychambers86253 жыл бұрын
Yo you got a part number or something like that for the black tube you put over the drive shaft into the top of the water pump housing?
@joshmartin57283 жыл бұрын
Check crowley marine. Full parts breakdown and exploded itemized view of all internal parts.
@ronniepullum6319 Жыл бұрын
What holds the pillar to the shaft
@BrandonsGarage Жыл бұрын
Pillar?
@jamesbaker67053 жыл бұрын
Can anything else be used besides 3m 847. I'm having trouble locating this stuff
@rikster66jan3 жыл бұрын
I saw someone recommended this as a substitute "3M 3M19718 847 Rubber & Gasket Adhesive44; 5 oz" Its on Amazon .
@tintdr Жыл бұрын
You don't need it just use gasket sealed same stuff
@Slippindisc4 жыл бұрын
Could you do a video on changing the plug wires on a 6hp Johnson? I found some videos of yours with my exact motor, and me and my have been trying to get the flywheel off with no luck.
@BrandonsGarage4 жыл бұрын
What year is your outboard? Also, are you using a puller?
@Slippindisc4 жыл бұрын
Brandon's Garage I’m thinking it’s like 68-69. The cover has the straight seam, not the swoop looking one, if that makes sense
@Slippindisc4 жыл бұрын
Brandon's Garage no puller available. Do we need one?
@Slippindisc4 жыл бұрын
Brandon's Garage is that what we need to get?
@happymac83722 жыл бұрын
How important is the shift rod keeper??
@BrandonsGarage2 жыл бұрын
You aren't shifting without it.
@javiermarante5344 Жыл бұрын
Hey I got a 1999 Johnson 25hp is this the same kit I need? Can’t seem to find any information on it
@BrandonsGarage Жыл бұрын
Yeah, same kit until 2005. It's a 2 cylinder right?
@javiermarante5344 Жыл бұрын
@@BrandonsGarage correct! Could you send me the link to this kit? Or is it the same as this one Evinrude/Johnson/OMC OEM Water Pump Impeller & Housing Kit 393630; 0393630 a.co/d/6kRYHcx
@BrandonsGarage Жыл бұрын
@@javiermarante5344 that's the one!
@javiermarante5344 Жыл бұрын
@@BrandonsGarage awesome! I will order that along with the carb rebuild kit this weekend, do they still make the oem carb rebuild kit?
@RigWars3 жыл бұрын
what was that little thing you tore off that costed 8 bucks??
@BrandonsGarage3 жыл бұрын
Its called a keeper. Connects the shift rods together.
@bwilson16492 жыл бұрын
@@BrandonsGarage Does it keep the nut from sliding off the end of the rod when disassembling?
@curtisliles37382 ай бұрын
60 to 84 foot pounds to torque a plastic housing? Seems like a lot!!!
@bankerlies6121 Жыл бұрын
That water tube can be tricky
@westoniii8 ай бұрын
Put the keeper and brass nut on before the foot. F the gasket if you have one. Cut it
@Marcelo_Molina..2 жыл бұрын
Muy bueno yo lo cambie...
@philliptaylor59814 жыл бұрын
Evinrude has closed? Will this effect us being able to get parts?
@-Viceroy-4 жыл бұрын
Nope
@BayouKid2 жыл бұрын
I hear mercury has purchased rights to build etec's
@dgage17763 ай бұрын
My Johnson 25 looks nothing like this
@RAMZEZvideoDesign4 жыл бұрын
Greetings. I am a professional video editor. I can make you a splash screen for your videos, as well as a channel trailer. Would you like to do? DJ_yr
@lawrenceflynn8245 Жыл бұрын
you done great right up until the last 2 O-rings and didn't show us where they went or how they went. So let down