Lowrance LMS-337 fish finder sonar depth sounder repair

  Рет қаралды 26,877

Jonny Fix

Jonny Fix

6 жыл бұрын

Repair of fish finder, depth sounder, sonar that won't power on, keeps blowing fuse.
Tools I use -
Soldering
Quick 861DW hot air station
Duratech TS-1640 solder iron
Multimeter
RMM760D - can be found under many name badges
Microscope
Luzky Zoom 3.5 - 90x simul-focus single boom stand trinocular stereo microscope
Camera - Lucky Zoom HD 14MP
Oscilloscopes
Siglent SDS 1102CML 100MHz 2CH
Philips PM 3305 35MHz 2CH
Bench supply
Powertech MP-3086 0-30V 3A

Пікірлер: 63
@fishermanfrank4522
@fishermanfrank4522 4 жыл бұрын
Brilliant work! Persistence pays and helps others (+ myself) with this particular problem. Pity that poor capacitors were fitted - replace the lot. Semiconductors generally reliable (also resistors if not overloaded). Well Done!
@JonnyFix
@JonnyFix 4 жыл бұрын
Cheers mate, glad you liked!
@brancarr1
@brancarr1 6 жыл бұрын
Excellent work Jonny!
@JonnyFix
@JonnyFix 6 жыл бұрын
Thanks mate!
@paulmeynell8866
@paulmeynell8866 3 жыл бұрын
Excellent really enjoyed this.
@rscelectrical7091
@rscelectrical7091 6 жыл бұрын
Nicely done, normally using some heat from your rework station will help loosen the tape bond.
@JonnyFix
@JonnyFix 6 жыл бұрын
True that. It's funny what you don't think about when you get into a process yet other times it's the first thing you reach for :)
@zx8401ztv
@zx8401ztv 5 жыл бұрын
Sneaky but good :-D Old acer/compaq lappys have similar looking ccfl inverters.
@bigpopaz29
@bigpopaz29 5 жыл бұрын
I have a lowrance LCX-37C that wont power up can you fix it or give it a go?
@antoniotrogrlic1804
@antoniotrogrlic1804 4 жыл бұрын
Thanks Johnny! Excellent video! I have a lowrance elite 5x that powers up and appears to be functioning normally until you take it out on the water. It will not read bottom, a lure, an anchor.... NOTHING! I have tried 3 different transducers, factory reset several times and nothing. I noticed that the transducer pings are not very strong (usually when you wrap your hand under the transducer the pings are very obvious). Any thoughts?
@JonnyFix
@JonnyFix 4 жыл бұрын
I would follow from where the corrector attaches to the board inside I think it will lead to a transformer that is driven by a couple of mosfets. Check to see if they are ok and if so you need to check the voltage on them with it turned on I think it's around 50v. There might be some diodes between the transformer and output connector as well. If that's all OK it could be the transformer has failed.
@wonderstudios7
@wonderstudios7 9 ай бұрын
Hello sir My garmin 585 is not reading depth can you guide me
@abelardodelangel5979
@abelardodelangel5979 5 жыл бұрын
se descompuso mi fcv 620 ecosonda furuno . no ve la imagen .creo ke es el display se descompuso ..do de códigos display.
@DIYSteveH
@DIYSteveH 6 жыл бұрын
Well Johnny, have the exact same issue, my transformer appears to be in better shape. BTW I called Lowrance and they wash their hands of anything older than 5 years old. Shameful as this unit was very expensive, and to not do anything at all for your customers is enough to change the directions of my dollars. My unit would stay on then after long periods would start flickering and screeching ( audio) on and of, on and off. I was able to get the mosfet from Amazon, but have found out that the transformer was manufactored for Lorwrance for this unit and is not a part I can get from GCi who really only sells to electronics manufactures and not to even part suppliers. The lady I got ahold of Dana was very helpful, but because the part is proprietary to Lowrance she could not give me the data sheet, but has committed to trying to find me something to solve the issue aka one just laying around. Will provide further comments when the results of that effort comes in. Clearly this is an original design issue by Lowrance and they are washing their hands of it at the expense of their loyal customers. I have purchased my last Lowrance after owning 9 of their products, roughly $6000 worth of business over the last 15 years.
@JonnyFix
@JonnyFix 6 жыл бұрын
Wow. Yeah sad to hear but a lot of manufacturers seem more interested in selling the latest model. Be interested to hear how it all ends and what you do to complete the repair. Cheers!
@anthonycash4609
@anthonycash4609 6 жыл бұрын
Steve Hastings I'm going threw the same thing right now with my Gen 3. I also tried to get help from there service department and was told I had only had 2 choices. Send it back for a reman unit at the cost of $636.00 or buy a new one. By the way this unit is only 2 years and 9 months old. Has only been used about 15 times and it just quit. They also will not get any more of my money. I will switch brands also.
@kjking3087
@kjking3087 4 жыл бұрын
@@anthonycash4609 same problem here broke pins male on back of unit, its from 2012 lowrance wont handle it over five years ...sucks
@Vampiric
@Vampiric 2 жыл бұрын
hey, i have the hook reveal 7x(gps only), could I buy a different motherboard that supports mapping?
@abdallahelectronic19
@abdallahelectronic19 6 жыл бұрын
Thanks Jonny for your experience ,just question , this finder work under water or on surface. Because electronic fixing its my hobby,thanks
@JonnyFix
@JonnyFix 6 жыл бұрын
This is for under water imaging
@abdelazizziati8513
@abdelazizziati8513 4 жыл бұрын
Please how to open lowrance x28
@javaman11-40
@javaman11-40 3 жыл бұрын
Hello Jonny - got ahold of a Lowrance Globalmap 5200c (no signs of cosmetic or water damage). When I connected it to 12VDC it powered up for about 10-15 seconds and then all the sudden went completely dead (no display, sounds or anything). I've confirmed I'm getting 12-15 volts. One thing I neglected to do in the beginning however was to connect a fusible link when I turned it on. Is there anything you could suggest I try at this point? Thanks so much.
@JonnyFix
@JonnyFix 3 жыл бұрын
It may have an internal fuse (like this unit) that has blown for some reason. At 4:59 you can see a fues holder toward the top and 2 orange wires going from it down to the board. Clearly this one popped it's fuse once and someone thought it was easier to add a fuse holder in to make it more easily replaceable given the original one is surface mount. You may have to do something similar.
@en4cer450
@en4cer450 5 жыл бұрын
A unit I have (very same model) powers on, but powers back off several seconds later. It's in excellent condition and very clean with no signs of water damage. Could you recommend anything to check out inside the unit?
@JonnyFix
@JonnyFix 5 жыл бұрын
Does it have a picture or does it just light the keys. An image might suggest the processor is ok. No image might be not booting (bad ROM) or no clock or there is an image but no backlight. The exact symptoms will help guide you. I'd be looking at all the power rails, make sure none are missing or incorrect.
@en4cer450
@en4cer450 5 жыл бұрын
Thank you for the suggestions. It had these symptoms when I tested it on a standard 110v-12vdc outlet converter but when i connect it to as 12v car battery, it powered on fine and the symptoms went away. I guess some fish finders act faulty on the certain converters.
@JonnyFix
@JonnyFix 5 жыл бұрын
@@en4cer450 Sounds like the output voltage was dropping because it couldn't source enough current or the regulation was rubbish and noisy.
@bksnow64
@bksnow64 4 жыл бұрын
I have this model, I need to get the data from it after a power failure. Do you think you could help me?
@JonnyFix
@JonnyFix 4 жыл бұрын
I'm sorry but I don't have a secure shipping address
@darrenfriend4625
@darrenfriend4625 2 жыл бұрын
Hello enjoyed your video on how to fix. Can i send my one to you to fix same problem won't turn on backlight suddenly. Thanks
@JonnyFix
@JonnyFix 2 жыл бұрын
Sorry mate, I have no secure address to receive it at.
@moy14ss33
@moy14ss33 5 жыл бұрын
How come my fish finder makes noise but It doesn’t show anything it just shows blank screen but it makes noise
@JonnyFix
@JonnyFix 4 жыл бұрын
Maybe it does have a picture but you can't see it because the backlight isn't coming on. Get a bright light up to it and see if you can see an image.
@andrewknox8986
@andrewknox8986 3 жыл бұрын
hi jonny i have a 7500c and the front glass has been smashed in transit. i have a replacement on coming where the buttons dont work how easy is it to swap out the buttons?
@JonnyFix
@JonnyFix 3 жыл бұрын
Shouldn't be hard at all, hopefully the reason for them not working is purely the buttons or the PCB they're on but you could swap your main board over to. Avoid trying to remove the screen from the chassis in case you ruin any water sealing.
@andrewknox8986
@andrewknox8986 3 жыл бұрын
@@JonnyFix thanks Jonny yes that's what I was thinking, stay away from the screen seals and move what's not working to this one coming. Do the buttons use done sort of seal around them as well?
@JonnyFix
@JonnyFix 3 жыл бұрын
@@andrewknox8986 from memory all the buttons are one large piece of rubber that creates the seal in itself when the board is screwed onto the back of it.
@andrewknox8986
@andrewknox8986 3 жыл бұрын
@@JonnyFix brilliant thanks Jonny that's what I was hoping for when watching your video above look forward to this arriving and getting to grips with it lol
@Blue.star1
@Blue.star1 2 жыл бұрын
What is the diameter thickness of piezo element used in this model
@JonnyFix
@JonnyFix 2 жыл бұрын
I don't know sorry, I'd imagine anything would work even if it was smaller.
@Blue.star1
@Blue.star1 2 жыл бұрын
Johnny can you teardown the sonar
@jacksonjacko8301
@jacksonjacko8301 Жыл бұрын
Do you still fox these things Johnny, if so how can we get in contact.
@781coolmind
@781coolmind 6 жыл бұрын
un-real i wish i had half your brain cool stuff...
@JonnyFix
@JonnyFix 6 жыл бұрын
Thank you sir. I'd give you half my brain but I might sound drunk on future videos :)
@ringerdiggsycobbsy6254
@ringerdiggsycobbsy6254 3 жыл бұрын
G'day mate I have a Lowrance Elite does 5X HDi which is not powering up at all all cables have power eccetera and I have tried my GPS Lawrence and other sound on the same cables and they all power up I have taken the circuit board out and trying to troubleshoot ID like to send you email photos if that's ok please
@JonnyFix
@JonnyFix 3 жыл бұрын
jonnyfix0 at gmail
@jimbeard1501
@jimbeard1501 5 жыл бұрын
can you repair a lowrance 104 lcx 12" screen
@JonnyFix
@JonnyFix 5 жыл бұрын
Maybe?
@jimbeard1501
@jimbeard1501 5 жыл бұрын
Do you think this is a project you would be interested in? If so what would it cost me to have you put it on the bench?
@JonnyFix
@JonnyFix 5 жыл бұрын
@@jimbeard1501 I appreciate your offer. Unfortunately I'm not set up to receive stuff from viewers.
@brianyawn7942
@brianyawn7942 6 жыл бұрын
Do you repair humminbird fish finders
@JonnyFix
@JonnyFix 6 жыл бұрын
I repair anything electronic. I have not worked on a humminbird unit yet.
@brianyawn7942
@brianyawn7942 6 жыл бұрын
My screen flickers when I hit power button. It has power to unit but will not start up. Don’t know much but I was gonna experiment. Any advice?
@JonnyFix
@JonnyFix 6 жыл бұрын
Follow the videos I have. I start with making sure the power rails are present. Hopefully its marked on the board what they should be and where to test. If there's physical damage inside (liquid ingress or leaky capacitors etc) fix that first then see where you're at. If no physical damage and all voltages present it gets a bit trickier.
@Blue.star1
@Blue.star1 3 жыл бұрын
Why didn't you repair the transformer
@JonnyFix
@JonnyFix 3 жыл бұрын
Never done one before. Suppose it's dooable but would take me forever to wind by hand. Could build a winding device but can't be bothered.
@troyhipsher9588
@troyhipsher9588 3 жыл бұрын
Jonny, are you on facebook? My father has seen this video and has questions to ask if you work on these since you fixed that lowrance graph in the video. If so, how would he get in touch with you?
@anthonycash4609
@anthonycash4609 6 жыл бұрын
If you like working on them you could make a good living fixing them. My personal opinion is they are a piece of junk. And if you have to rely on lowrance get ready for being abused by there customer service department. They give you only 2 options send it back at a cost of 636.00 to get a reman unit or buy a new one.
@JonnyFix
@JonnyFix 6 жыл бұрын
Not surprised. Anything with low production volume (compared to other consumer products) and even more so with niche markets will almost always be hard to get some parts and any info for.
Lowrance hds5 fish finder repair
36:45
Joseph Salmans
Рет қаралды 11 М.
Mom's Unique Approach to Teaching Kids Hygiene #shorts
00:16
Fabiosa Stories
Рет қаралды 34 МЛН
New model rc bird unboxing and testing
00:10
Ruhul Shorts
Рет қаралды 29 МЛН
路飞太过分了,自己游泳。#海贼王#路飞
00:28
路飞与唐舞桐
Рет қаралды 32 МЛН
Furuno FCV-585 fish finder sonar depth sounder repair
23:00
Jonny Fix
Рет қаралды 22 М.
Change Your Fishing Forever With This Google Earth Trick
16:58
Fish the Moment
Рет қаралды 451 М.
LCD REPAIR !!
21:06
K C Dash
Рет қаралды 173 М.
Wanptek EPS3210 Power Supply Review & Teardown.
34:09
Jonny Fix
Рет қаралды 1,7 М.
No.035 - Locating a PCB short circuit (10 minute)
10:46
IanScottJohnston
Рет қаралды 167 М.
LOWRANCE LMS-1332C,337CDF,332C, 3500C - N2344DVD
2:32
BennettMarineVideo
Рет қаралды 50 М.
Basic Settings on your Lowrance Unit from "The Professor"
4:09
Sherry Baker
Рет қаралды 1,1 МЛН
Sonar Basics: How To Find Fish
7:16
TacticalBassin
Рет қаралды 995 М.
Transducer Cable Repair
13:41
SMALLVILLE FARM
Рет қаралды 24 М.