Was beginning to think I was only one that had a 2150 didn't see any other videos of them till now

Bless you Bellhopper, this video is pure gold for your viewers. I have been learning so much in everyone of your educational videos. We turn off the TV and turn on Bellhopper's educational videos!!!

Hi Bellhopper!!😀😀 One of the biggest reasons why you will burn up a saw running 50 to 1 is because they run a dull chain and learn on the saw and make it get hot. I have never burnt up any saw running 50 to 1 because I never run a dull chain. If people want to continue to run dull chains they definitely need to be running 32 to 1 in them. I have yet to ever burn up a top end in a saw. The only thing I have ever had fail are the crank bearings and that's only after hundreds of hours of heavy logging. But the top ends are always still fine. So I just put a new set of bearing and seals in and away we go again for another several hundred hours. Take care my friend!!😀😀 Logger Al

Alvin brought me a 350 husky, got it running, I think I need to port it! That’s an angry little saw! Thanks again for all you do buddy!👍👍👍👍🇺🇸🇺🇸🇺🇸🇺🇸🙏🙏🙏🙏

Thank you for the share! Watching you tweak that engine was fantastic!

Amen Bellhopper. I’ve been preaching more oil in gas for years. I tell all my customers to run at least 40:1. I mix mine a little heavier so it’s probably 38:1 or 36:1. Ported saws gotta have lubrications to last. Preach it brother, Amen.

Fastest rebuild on youtube ! Good work Bellhopper. Thanks

The man knows what he’s doin folks👍🏻 heck of a job Hopper, I enjoyed hearing it fired right up!

True a ported saw needs more oil mix so not to burn up a saw. These people that think using little oil helps🤔 yeah right.

They are a nice little saw, put a stihl ring in my last one. I use 40 to one my small saws and brush cutters and around 35 to 1 on my mid range saws especially the x torque and auto tune saws and 30 to 1 on my 3120 and the 088 when ripping posts. Oil is cheaper than a piston and cylinder in Australia from memory is around $ 800 Au for a 372.Cheers every one.

I knew Dr. Bellhopper would have the right medicine to make little johnny feel better! I think 50:1is just a plan for saw factories to sell more stuff. Keep up the great work 👍👍💪💪😁😎🇺🇸!

Sounds great to by the way buddy. Great work as usual.

Amen brother! After I started porting saws I run 32:1 most of the time and some times 40:1 but I do not run 50:1 anymore at all in anything!! And we got snow too and I hate it! I've been out cleaning porches and steps all morning

SHE SOUNDS HEALTHY TO ME BUDDY 👍🏽👍🏽👍🏽

I have mostly older hand me down saws that I've fixed up and I only run 32:1 in em

I have one of those in a box took it apart about a year ago. Think its time to see if I can get it back together again

I have a mac pro 10 10 that was my dads and your accent sounds Appalachia just like mine. I live in WV and am looking for a legit guy who can get this power saw back to its glory. It still starts 3 or 4 pulls but this Mac means the world to me because it was my dads and the first saw I learned to run. I watch BBR and that's how I found and subscribed to you in 2020. Please message if you have time. Thank you.

Hoooooppppeeeeerrrrrrrr 👍👊💚🌳💚🌳

No snow out here on the water. It was extremely foggy this morning though you could see the mist particulates in the air, and it was only low 40s but jeez wasnt it cold, I swear humidity is everything...hot it cold shew it stays humid ALL the time out here

Fatten the mix up on him in carb then. Saw might not run as good as it could. But might help in repair area for you. Unless your charging him family rates.

The perfect Hopper-tune-ity..

I run about 30 to 1 plus a dab of staybul.

Hello Mr Bellhopper.

Man (Jun bug ) AKA you lol..I love watching you..

Right on brother

My three choices on oil all mixed at 40 to 1 motul 800 Maxima formula K2 or klotz R50

Yep I'm here

Bellhopper if you catch other videos on KZfaq do so with this Twin Sticks Garage guy in Canada as he into semis

You are a fine saw tech

You need to do a little hot rod like a 2149 turbo if you need you need one to do it to I will send you mine lol

I run 32:1 also. Learned a hard lesson with 50:1 on a 357 when I was a strappin lad. Lol

At this point i know more about saws than i should considering i dont have one lol.

Nice work- Is it possible for you to replace fuel line on a CS2245, mine is giving me fits. thax,Bill

Those saws are known for ripped intake boots you should check if it’s sucking air

TELL THEM TO MIX THERE FUEL 40 TO 1 MAYBE THEY WILL LISTEN TO YOU GREAT JOB BELL HOPPER BE SAFE BUDDY

He needs to get a old classic Mac that runs😆

Compresure.. lol you had going there.

Wizard!

Man I have the same one as that shes a runner..but I have some questions about it..

i almost fast forward it to see it run but you work so fast.

You got a twin cyl Echo in that shop?

They last a lot longer with decent amount of oil.too little pretty risky..plugs are cheaper than motors..Lol.

👍✊Nice fix Hooper

👍🏻👍🏻👍🏻

What do you use on the cylinder base to seal it I've been using Honda bond with no luck just curious what you use that works

50:1 is a recommended my manufacturer that's not eched in stone

Yo!

What did you have to do to put .375 chain on it,i have a 350 Husky i'd like to do that too?

Ler gas little to high sou end air or H ,,becose of that on the end of video the fasoline sprint out on carb,,,put the high speed little lower on 12 to 12 200 rpm end min gas inaf to worck like a cat in rumble.,,,one step low...good luck

So our husquavarna rancher says to run it at 50:1 so what do you recommend??

My poulan pro says to run 50:1 should I swith to 40:1? I just buy the premixed fuel

WAY TO USE OLD PARTS TO FIX THE SAW

And yet another good reason to not run 50:1 in nothing

Is that their version of the 350 it reminds me of mine

Not uncle jim

I run all my saws at 32:1 bell hopper

You know I only run 32-1