Cheap Homesteading is fixing a shutdown problem on a jonsered 520 sp. as well as adjusting the carburetor.
Пікірлер: 51
@seanshields864 жыл бұрын
I have a jonsred 535 passed down from my granddad... hands down one of the BEST saws I ever had... usually starts within the first 2 pulls, gives it hell when I squeeze that trigger. Lots of power. Cheers.
@shelbywilson1145 жыл бұрын
I got one of these saws from a customer for free. It runs pretty good for an old 49cc
@cheaphomesteading5 жыл бұрын
It was surprisingly strong for its size. Thanks for watching
@waynemifsud35874 жыл бұрын
Is yours a 490 by any chance ?
@shelbywilson1144 жыл бұрын
A 520
@keeganfoster17924 жыл бұрын
Them old jonsreds go forever my grandfather got one used from a guy used it years he burned wood for heat. So he stopped burning wood gave it to my father to use he used it for several years also used it yearly cutting wood to burn it finally started to become not very reliable so he gave it to his brother and he used the damn thing for several more years no shame for that chainsaw at all jonsreds last a long time an very reliable 👍🏻👍🏻
@Wrenchesandboards4u2u5 жыл бұрын
Very nice you got it running alot better. Thank you for sharing friend.
@DeezNuts-xo2ee4 жыл бұрын
Should have done chain maintenance first
@georgedavall94492 жыл бұрын
Indeed!
@grizzlyaddams36062 жыл бұрын
Also known as: The video that single handedly took down Johnsered. FACT: I've run Jons for 20 years and NEVER had any of these, "problems". Cool video tho. Needed that carb adjust tech.
@mikesgeneralservicesllc39153 жыл бұрын
New chain would do wonders as well
@jonnorton97204 жыл бұрын
Looks to me like the chains dull...not very big chips
@georgedavall94492 жыл бұрын
Chain IS dull !
@SwampDonkey5305 жыл бұрын
Sometimes if you blow a ring it will still run, but when it gets hot it'll quit or lock up, then once cool again it starts and runs good again. It happened to me, took me the longest time to figure it out.
@bradrolling86374 жыл бұрын
Swamp Donkey, it's been a year , but if you see this please let me know if you had any other symptoms. My poulan runs and cuts great , but after 5 -10 minutes it bugs down and sounds like it is starving for fuel, and then quits. It won't start again until cool
@SwampDonkey5304 жыл бұрын
Brad Rolling sounds exactly like I said, probably a ring, in which case, being a Poulan you’re probably better off junking it and getting a new one 🤷🏼♂️
@bradrolling86374 жыл бұрын
@@SwampDonkey530 I know, you're probably right. It was my late dad's so I'll hang onto it for sentimental reasons. Thank you for the info, I'll check it out.
@SwampDonkey5304 жыл бұрын
Brad Rolling yes, my junk pile is extensive and large, lol 😂 must have 2000 cylinders
@homegrowncountryhomeplace5 жыл бұрын
Happy Thanksgiving Pete and have a Blessed Day Friend!
@cheaphomesteading5 жыл бұрын
You too. hope you and you family have a blessed thanksgiving.there is so Much to be thankful for. God bless you guys
@HomesteadingwiththeHeberts5 жыл бұрын
looks like you got that saw running better
@ryanodonnell37174 жыл бұрын
Just a curiosity question. At 5:48 in the video there is a side view of the chain. It looks like there is A LOT of slack dip in the chain. Shouldn't it be quite a bit tighter?
@cheaphomesteading4 жыл бұрын
The chain must have road up on the bar the cut just before 5:48 the next cut it’s back and no slack thanks for watching man
@ryanodonnell37174 жыл бұрын
@@cheaphomesteading ahh that makes sense now. I'm no pro with saws or anything, but iv'e always been taught to make sure there isn't slack....so good to know. Thank you for making the video by the way. It was very helpful for sure. I have an old Jonsered 520sp that hasn't been used in many years, and wouldn't start. I tore everything down, and working like a champ now. I couldn't figure out how to fully pull the carb but got enough apart to clean. The connections to it seemed so different than most carbs so wasn't sure.
@georgedavall94492 жыл бұрын
@@cheaphomesteading No Sir, your chain was too slack, and very dull. That saw was struggling the whole time. One of those cheap little tachs off Amazon make tuning a whole lot easier, precise, and save the motor, eh. Peace
@TheUltimate652 жыл бұрын
The chain must be sharpen up, and have inspected the piston, sylinder...se you pull the startline much out...not normal when the engine its varm
@waynemifsud35874 жыл бұрын
Hi there, l really liked your video, l have a Jonsered 490 and was wondering on how to service it if you have a video of that by any chance ?
@bradrolling86374 жыл бұрын
Please help me! ☹😟 my Poulan 1800 runs great, but after cutting for 5-10 minutes it bogs down and quits. Let it cool off and it goes through the same thing. I've already adjusted the carb per video. Please reply, all opinions are welcome.
@cheaphomesteading4 жыл бұрын
You can try to open the high jet a little bit more. Because it sounds like it’s heating up.
@cheaphomesteading4 жыл бұрын
It is possible it’s a fuel filter issue and it slowly runs out of fuel. But I bet if you open up the high jet a little bit more. turn the screw left just a little bit and then try it
@bradrolling86374 жыл бұрын
@@cheaphomesteading Thanks! I'll try that next. I just replaced the fuel line and filter. I failed to mention this is the 1st time in 9 years it's been started. I broke down and cleaned the carb thoroughly. You wouldn't believe how hard it is to find a carb rebuild kit in Montgomery, Alabama! Everything around town is Husqvarna or Stihl. Thanks again and I'll keep trying until it runs true. It was my late dad's saw.
@bradrolling86374 жыл бұрын
@@cheaphomesteading poulan IS WITH Husqvarna . Opening up the high side is clockwise, correct?
@cheaphomesteading4 жыл бұрын
It’s counter clockwise to open it up. Clockwise. close it. Hope you get a running man
@rickyurrutia91823 жыл бұрын
Just purchased today one at Lowes and it turns off like in 5 mins...
@JoseOrtiz-im5wu5 жыл бұрын
When you adjust the high and low side , do you have to do it revved up or can you do it at idle?
@cheaphomesteading5 жыл бұрын
The high needs Too be full throttle When you adjust it. the low idol adjustment is made at idle. Thanks for watching men
@phyllismulkey37785 жыл бұрын
good info ty
@mirharoon77754 жыл бұрын
Sir When I Press Accelerator My chainsaw Off Please Reply me
@cheaphomesteading4 жыл бұрын
It is running out of fuel first check the fuel filter in the tank. Then check the fuel lines if that is ok you will have to clean the carburetor out one of the small holes are plugged in the carburetor. Hope you get it running thanks for watching
@mirharoon77754 жыл бұрын
@@cheaphomesteading But Sir Carburetor is new
@mirharoon77754 жыл бұрын
Replace
@cheaphomesteading4 жыл бұрын
If you open up the low jet a bit more see if that helps when you hit the throttle. You might have to raise the idle a bit but don’t raise it higher than the chain will stop turning when you let off.
@mirharoon77754 жыл бұрын
@@cheaphomesteading Sir tell me how I can Restore this problem .
@notavailable73793 жыл бұрын
The high side has nothing to do with starting
@cheaphomesteading3 жыл бұрын
The high side screw does adjust the high side but if you set it to the rich side on the high side screw. It will be hard to start. If you have the high side set correctly or to the lean side it will start easier. The low side screw is meant to adjust idle and the moment you rev it up. Thanks for watching
@notavailable73793 жыл бұрын
Chain is dull as hell and saw is underpowered
@Ketis19858 ай бұрын
Chain was dull, but those saws are not underpowered.... they run 8pin .325 as a standard.... you gotta have good power to do that....