Jonsered 2152C Tune up

Рет қаралды 12,733

Күн бұрын

I don't see a lot of Jonsered saws come through the shop but when they do its no big deal because they are basically red Husqvarnas and I can easily get parts. This one came in for a "once over". #smallenginerepair

Пікірлер: 42

@mendonesiac 7 ай бұрын

It's pretty obvious that Husky manufactured that saw, it's almost identical under the shell. I really dig your videos on rare/discontinued saws that most of us never get to see.

@TheGreasyShopRag 7 ай бұрын

These are the units that come into our shop. I have heard of shops not wanting to work on older equipment but we usually give them a chance.

@patrickvennard838 5 ай бұрын

Is it a 346 or a 353?@@TheGreasyShopRag

@TheGreasyShopRag 5 ай бұрын

@@patrickvennard838 346

@leonardryan8723 3 ай бұрын

My kind of chainsaw 2195 jonsered little work under the hood and check the turbo over . 😊

@TheGreasyShopRag 3 ай бұрын

Thanks for watching!

@steveriggenbach90 Жыл бұрын

Great information. Try to stay with oem hardware. Working on a Husqvarna saw , recoil screws are loose. If totally stripped I used the holes as a pilot hole. Any tips before it gets that far. Thanks

@TheGreasyShopRag Жыл бұрын

I've epoxied screws in place. Never got any complaints about stuck screws but then I've always told the owner about that style repair.

@steveriggenbach90 Жыл бұрын

@@TheGreasyShopRag pls dbl chk me , it’s been awhile, but I used #12-24. X3/4 for stihl trimmer Just screws right in.

@TheGreasyShopRag Жыл бұрын

@@steveriggenbach90 Well they should be metric screws. Never checked a 12-24 for metric fit. I'm gonna investigate.

@steveriggenbach90 Жыл бұрын

@@TheGreasyShopRag have a great NEW YEARS. Take care

@nraugmoobleegnkaujhmoobdaw2084 Жыл бұрын

I need my clearn too.

@Bobo-ix9rw Жыл бұрын

nice one would have liked you to check and clean the spark arrester screen and take off the bar and chain for a clean and check for good oil flow. but im sure ya did it just not showing here in the vid. greetings from good old germany yeah you have an international audience :)

@TheGreasyShopRag Жыл бұрын

Like you said, there are things that don't get shown on these videos like dropping a saw into a log and tuning it or chain sharpening. I feel fortunate my employer allows me to capture the video I get over the bench. At 8:10 in this video I'm looking at the screen which is mostly exposed. I only pull them apart if I can hear they are plugged or if I'm looking for evidence of plastic bearing cages 😞 Thanks for watching (from Germany)!

@chrispriore476 5 ай бұрын

I have same saw. No shops around where i live. I can get to start when cold and run for bit then thats it. plug fouls up and wont start again. Checked comppression, had about 50lbs. So, i bought new piston and jug. replaced. same thing low compression. Somethings not right. you have any suggestion on what to do next. I have no breakdowns of the internals. i'm assuming a leak somewhere. guage stays under pressure... thanks and love your video

@TheGreasyShopRag 5 ай бұрын

I guess I'd start by confirming the problem isn't with the gauge.

@chrispriore476 5 ай бұрын

@@TheGreasyShopRag checked with air compressor. Goes to 150 which compressor is set at. 120 on another broken chainsaw. I did a leak test in fuel line with mighty vac to 10lbs. It goes right back down after a few seconds. Not sure if it’s related. This saw sees very little use fyi.

@TheGreasyShopRag 5 ай бұрын

@@chrispriore476 If the fuel line doesn't hold 10 psi then there is a hole in it or a leak in the carb. Those issues need to be addressed.

@jonathanfierberg3807 10 ай бұрын

Tightness = torque

@Doc-Cole_Trickle-of-Chainsaws Жыл бұрын

👍🆙S

@jonathanfierberg3807 10 ай бұрын

Do you drink bud light 💡

@andysears5552 10 ай бұрын

Hi, I have a Jonsered 2165, rebuilt carb and new fuel lines, but can't work out how to replace the trigger/safety spring? Took it out cos my throttle cable wasn't pulling the cam on the carb, but now i can't see where it hooks into the trigger> Have you any video clips showing where it goes? Cheers.

@TheGreasyShopRag 10 ай бұрын

Sorry I don't have anything to help you with that.

@andysears5552 10 ай бұрын

@@TheGreasyShopRag Ah, no problem, thanks anyway. Hopefully, someone will show a video sometime...or i could always buy a new saw!

@andysears5552 10 ай бұрын

Trial and error showed the way! The spring locates into the trigger by hooking into a small recess at the front right side of the throttle cable cam wheel on the trigger. You have to hold the spring tilted to the left 90 degrees, feed it under the plastic protrusion molded into the left side of the saw's handle (inside the handle where the safety trigger goes), there is a small channel built into the left side of the throttle cable cam wheel, slide the spring end along this channel until the front area of the cam is reached (nearest the saw engine), then the really fiddly bit is trying to locate the hooked end of the spring into the small trigger recess, not on, but on the right of the cam wheel (not on the cam wheel)...really fiddly to get it right, took me hours!

@KensSmallEngineRepair Жыл бұрын

Another great Vid Scott. What Brands does your place sell besides Husqvarna?

@TheGreasyShopRag Жыл бұрын

Thanks! Besides being a full line Husqvarna dealer we sell Echo, Toro and DR Power but we'll try to fix anything 🙂

@robertI153 Жыл бұрын

Hi from Australia. You might not think so, but compared to here you seem to have a good supply of spare parts. Considering the cost of labour and parts here, the bottom end of outdoor equipment is not worth taking to a mechanic to repair. It’s diy or the scrap bin. Cheers

@TheGreasyShopRag Жыл бұрын

That scrap bin is one of my favorite places to visit 🙂Thanks for watching!

@majamarijana1575 Жыл бұрын

Husqvarna 353.

@nraugmoobleegnkaujhmoobdaw2084 Жыл бұрын

Where you at?

@benbradshawjr2856 Жыл бұрын

No grease between the air filter seat??

@TheGreasyShopRag Жыл бұрын

If the intake runner is clean then I don't even consider using grease.

@LittleRiverKingfiser 4 ай бұрын

I need a new fuel tank for my CS 2152C will the fuel tank from a CS 2152 fit? Are they the same other than the C for CAT?

@TheGreasyShopRag 4 ай бұрын

I see ten seperate versions of that saw and 8 use the same tank. What is the product # on the serial tag?

@LittleRiverKingfiser 4 ай бұрын

Hi, thanks for the reply! The only numbers I could find were on the plastic top cover. 2152 52cc 4HVXS.0525EA@@TheGreasyShopRag

@BruceLyeg Жыл бұрын

Not really about this video, but have you ever injured yourself working on something?

@TheGreasyShopRag Жыл бұрын

One time I reached under a mower deck to see if I had sharpened the blade yet. I still have the scar from the seven stitch cut that I got.

@BruceLyeg Жыл бұрын

@@TheGreasyShopRag I have a friend who lost two of her fingertips cleaning off built up clippings on the underside of her mower deck.

@TheGreasyShopRag Жыл бұрын

@@BruceLyeg Yikes! I guess those blades were sharp too!

@patrickvennard838 Ай бұрын

I think the Jonsered saws are better made.

@TheGreasyShopRag Ай бұрын

I have no reason to believe that but its possible. Even if they're not, the perception that they are better might be there.