No video
Jura Restoration | Refurbishing and Deep Cleaning
Рет қаралды 131,664
Күн бұрынEven after 13 years, this Jura coffee machine impresses with its timeless design and sophisticated technology. Even when dismantling the housing, it is noticeable that many innovative solutions have been used here. The restoration of the Jura ENA 5 was a lot of fun. I am sure that the device will continue to fascinate with its great design and delicious coffee for many years to come.
M Y T I P - B O X
_________________
www.buymeacoff... ☕
www.paypal.me/...
Affiliate links:
Bezahlter Link:
U S E D P A R T S
_________________
OKS Multi Silikonfett/OKS silicone grease: amzn.to/3cX39eV
O-Rings: amzn.to/3oJiKUs
Menzerna Polish Set: amzn.to/2PDuE68
Milchschlauch: amzn.to/2RiO8NL
Cream 12% Oxide: amzn.to/3vwZHQq
Oval Bit: amzn.to/3c1PHIt
T O O L S
_________________
Oval Bit: amzn.to/3c1PHIt
Proxxon 22295: amzn.to/32IeGyk
M Y W O R K
______________
3:17 the first opening after 13 years
6:20 this is a 13 year old coffee ground
7:04 I'm cleaning all parts thoroughly
7:31 the chassis also needs to be cleaned
7:59 everything is clean now
8:25 the grinder is back in its place
8:37 the logo and the coffee spout are broken
9:00 I bought new parts
10:16 I like the rotating spout to adjust the ENA for one shot or two
10:42 of the cleaning tablets which are too thick
10:53 I recommend the thin ones
12:57 now, I'm doing a little function test without coffee beans
13:22 the case is scratched
14:35 now it's looking a lot better
16:09 I'm treating the plastic parts with 12% hydrogen peroxide
17:25 I'm changing the scratched cover with a new one
18:21 that looks very clean
#Jura #Repair #Restoration
@SoftieFloopz Жыл бұрын
Thank you for this video. I finally took my machine apart and cleaned it thoroughly! Your video was a great tool to assist! Only some parts were unfortunately skipped in the video, but with some common sense and this video, everyone should be able to get it done! Appreciate it! Have a great coffee! 💪🏻
@atnstn Жыл бұрын
Time stood still watching this video. Medicinal feast of the senses. Truly masterful. Highly appreciated.
@laurieprince2666 2 жыл бұрын
I loved watching this deep clean and reassembly of the Jura 5. You are patient and knowledgeable! Thank you for showing me what's inside the big box that goes "grrrr....."
@tonymontana897 3 жыл бұрын
It's a brand new 2nd hand one !!! Excellent video Sir. Thank you for sharing.
@philippeclost5459 Жыл бұрын
Astonishing job! Will do the same early next month on my 11 years old ENA3 (becomes a bit grumpy and Jura's support is not providing many spar parts anymore...)
@evgeniyn6909 Жыл бұрын
Thanks for the review 👍. I have a problem with this coffee machine error 8. I will try to bring it to my senses on my own
@countrymen 6 ай бұрын
I’m really impressed and motivated to do same thing to my ena3 - very well done 👏
@DukeofMiami 7 ай бұрын
That was very enjoyable to watch. Now I know what those ASMR people are on about. Just bought a Jura 9. Can’t wait to give it a good cleaning.
@cvdb2471 3 жыл бұрын
Excellent video! I have the Jura Ena7 which is almost identical, only has a different looking rotor knob.
@fmarandon 2 жыл бұрын
Your videos are just perfect with an amazing quality ! I loved all of them and I am really one of your early fan ! Thank you so much. I've just purchased the Proxxon 28660 polishing tool following this video as I was really amazed how you managed to renovate the plastic covers and bring their brightness with this tool. What product/cream do you put on the tool sponge ? I'm very impressed, really... Again thank you for what you do, it helps the community so much. I am specialised in Delonghi machines but learning now Jura with you. Big hugs from France :)
@yt.myworks 2 жыл бұрын
@Florent Marandon many, many thanks for the great words. I use Menzerna products for polishing: amzn.to/2PDuE68. Thanks very much and greetings back to France.
@joebroderi Жыл бұрын
Excellent video, just what I was looking for ! I really like the polishing bit, could look at it all for hours ! very theraputic ! Good work !
@ejsiqueirajr 4 ай бұрын
Thank you for sharing. I was looking for something like this for a long time to do an internal clean on my JURA ENA4. So first, have to find the oval bit.
@Gazavich 3 жыл бұрын
Perfection every time, I salute you sir 👏 Ena 9 owner 😉👍
@OURAL993 2 жыл бұрын
Super bien fait et très instructif, bravo!
@Efka-po3hi 3 жыл бұрын
A już mieliśmy dawać ekspres do serwisu , mąż bierze się za rozkręcanie może uda się nam naprawić. Słabo leciała kawa i zawsze pomagało wyczyszczenie wylewki ale niestety tym razem nie pomogło. Dziękuję za filmik :)))
@Efka-po3hi 3 жыл бұрын
No i niestety wszystko wyczyszczone a nie działa, nie leci woda :( może jakaś podpowiedz ?
@yt.myworks 3 жыл бұрын
Nic? A ze spieniacza też nie? Czy była używana woda filtrowana czy prosto z kranu? Jeżeli woda nigdzie sie nie pojawia to będzie gdzieś zakamienione lub zepsuta pompa.
@Efka-po3hi 3 жыл бұрын
@@yt.myworks Ze spieniacza leci, woda filtrowana
@yt.myworks 3 жыл бұрын
Trzeba sprawdzić wszyskie wężyki jeden za drugim od początku obiegu wody. Czyli jedną końcówkę odłączyć aby sprawdzić czy jest drożny. UWAGA woda może być gorąca i pod ciśnieniem. O niebezpieczeństwie z prądem chyba nie muszę wspominać 😉
@Efka-po3hi 3 жыл бұрын
@@yt.myworks Bardzo dziękuję za zainteresowanie. Jutro z samego rana mąż zacznie robić tak jak Pan mówi. Dam znać czy się udało. Pozdrawiam.
@bradleypaoli1953 3 жыл бұрын
Thanks for the video. I have an Ena 5 as well and I've been thinking of doing some work on it. I didnt realize how poorly designed they seem to be internally.
@marctardy6883 Жыл бұрын
Très bonne vidéo !! Elle m'a permis de remettre à niveau ma machine qui est redevenue comme neuve 👍 Merci beaucoup
@het_gele_teken 3 жыл бұрын
love the sound effects! drinking coffee from that dirty machine constitutes a health and safety hazard, just sayin'
@MJ-ps5yq 5 ай бұрын
This is an absolutely beautiful and mesmerizing video. Thank you for this great information. We have a beloved Ena 3 and I have been wanting to do an in-depth cleaning. Not sure I can go as far as you did though. 🥺
@yt.myworks 5 ай бұрын
Proceed gradually, first remove the brewing group, clean it and replace the seals. Then repair the outlet valve on the right-hand side and maybe clean the grinder at the end if you feel up to it. Always take lots of pictures to see how it should be put together.
@matthewbeausoleil5399 6 ай бұрын
This was very satisfying to watch. I have an Era 4 that is 2 years old and the brew group appears to be struggling a bit. I'm tempted to go through it like you did here. The cleaning tabs just don't seem to do the job.
@yt.myworks 6 ай бұрын
Hello, the cleaning tablets only clean from the inside and let the seals dry out a little, which makes the brewing group sound strained.
@terneuv 3 жыл бұрын
Quel travail 👍 . Cela va bien aider du monde 😉 . Il faut que je nettoie en profondeur ma ENA Micro 9 One Touch , le marc de café s'accumule énormément à la sortie du groupe , et même le nettoyage avec la pastille n'y change rien 🤔. 👏👏👏👏👏👏👏👏👏👏
@21348966 Жыл бұрын
Dear sir. First of all i would like to thank you for the excelente vídeo showing how to restore and clean a Jura Ena 5 coffee machine. Very nice job. I follow your instructions, bought Jura originals O'rings and put may Ena5 in the best operational condition which it was possible after many years of good performance. However, just after 3 days of normal operation, my Ena5 start to ask for to open nob in order to fill the system with water despite i do not had make any operation to empty the water content in the machine. I open the nob, the water flows normally and, after a few seconds, the machine ask to close the nob. Closed the nob, the machine ask again to open the nob to repeat the filling of the system. And so on, until the water tank be empty. I made a inspection in the circuit line of water trying to find any clog or leak and, to the water tank, passing through the pump, and after the termal block, i do not found any problems. I performed a total descaling and cleaning of my machine just after the restoration and this operations was completed without any problem. Could you please gave me any orientation of how to fix this problem?
@yt.myworks Жыл бұрын
Hello, the problem could be with the flow meter, that's the round white part. It may be incorrectly connected or blocked. Check hoses and cables to see if they are not connected backwards.
@czarliw1644 Жыл бұрын
Perfect job! 😀👍
@mikaelilmari 2 жыл бұрын
Excellent instructions, thank you for enabling clean up without breaking anything :-)
@bartfrederiks5892 5 ай бұрын
@aksuli1 I first glued the broken parts back together, and then added 2-3 mm thick layer of epoxy glue on the top of the base plate, all around the crack. I'd use the best quality epoxy glue that you can find...
@ahmedgrissa5077 3 жыл бұрын
Excellent travail... Bien précis et complet avec les bons détails.... Bravo
@philippeclost5459 2 жыл бұрын
Bonsoir, j'ai une ENA3 et impossible de faire tourner le couvercle Jura en face arrière ! Une vraie galère... Quelqu'un peut me renseigner?
@runmarfly133 2 жыл бұрын
Very good job and thank you for sharing your works which are very useful. I would like to have your advise regarding an issue. My machine boots up normally until the brew unit appears to drive upward without stopping. A terrible crunching noise ensues and I have to switch it off. Without the brew unit, I found out that the engine is always running with no sequence (clockwise and counterclockwise turns). I cleaned the brew unit according to your videos and it moves perfectly. So what could be the problem, the motor, the encoder, or something else ? Thanks for your help...
@yt.myworks 2 жыл бұрын
@Run Marfly first you have to bring the brew group into the basic position, this is the position ready for receiving ground coffee.
@runmarfly133 2 жыл бұрын
@@yt.myworks Problem fixed. I found out that the brew unit wasn't well fixed on the steelplate (between motor gear and brew unit) by the screws. So I decided to change the steelplate and to change the screws as well. These two parts are well tighten together and it works. Regards
@yt.myworks 2 жыл бұрын
@Run Marfly well done 👍
@erniemendoza2298 10 ай бұрын
First of all, this is a wonderful instructional video. I would most likely do a complete renovation/refurbishing of a Jura ENA4 that I have just purchased. What you produced here is a phenomenal guide. But before that, I'd like your thoughts about the frothing mechanism that would not extract milk nor produce frothed milk. It just dispenses hot water. I have cleaned the external components thoroughly and also the container. Not enough pressure? Your thoughts/ideas are appreciated.
@yt.myworks 10 ай бұрын
Hello, it's difficult to say but it could be that the Jura outlet valve is broken.
@radosimun 6 ай бұрын
Hi, thanks the video, it a geat help. I am having issues to disassamble the plastic covers, do you use any special bit for screw behind the jura cover below the water tank? Thanks
@yt.myworks 6 ай бұрын
Hi, here is the special bit to open the cover: amzn.to/3c1PHIt
@worldwideinterests1 2 жыл бұрын
Was hoping I might see something about the top rotary switch. Trying to understand why one would lock up.
@henkzaanstad2256 2 жыл бұрын
Geweldig.. Thanks... Greetings from Holland
@mahmood6667 5 ай бұрын
I have jura ena 9. The motor for the brewing unit does not stop and there is no error code. What's the problem
@maikl9449 Жыл бұрын
В видео не показано. Фиговину, за задней эмблемой, надо в сторону бочка сдвинуть. Это тоже большой кронштейн который крышки держит.
@ramonbeltran6561 5 ай бұрын
It is very likely that it has broken where the infusion group is attached to the motor, which is not unusual.
@dralusion Жыл бұрын
fantastic work! I have an ena 9 and the milk frother is coming out. i can see the heated water going in the drip tray, but nothing is coming out of the spout. same thing happens when I do a C clean.
@yt.myworks Жыл бұрын
I think that the drainage valve is no longer working properly. Here is a video on the subject: kzfaq.info/get/bejne/bsmoaZOXtbe0cps.html
@dralusion Жыл бұрын
@@yt.myworks thanks for the suggestion, but the coffee runs fine. its when using the steam/frother/milk. it will dump it in the try. nothing comes out of the steam/frother/milk spout
@yt.myworks Жыл бұрын
Okay, I suspect that a o-ring, maybe in the rotary switch, is broken. Or in another valve inside the machine. You have to check exactly where the water is coming from.
@Ricardo6784 2 жыл бұрын
Great Video
@maxena8340 2 жыл бұрын
Grand savoir faire 👍👍👍 great know-how
@nhamochiuswa2658 2 жыл бұрын
I have a Jura j6 am trying to put back together. I bought it used and it was disgusting. Your videos have been a great help but sometimes miss the little things like connecting the hose back on the brew group. Awesome videos hope you can edit one of your videos with this information. Thank you.
@yt.myworks 2 жыл бұрын
Unfortunately not everything can be shown in the video, otherwise the film would be too long.
@nhamochiuswa2658 2 жыл бұрын
@@yt.myworks maybe one notable tip before i put this all together. Thank you.
@yt.myworks 2 жыл бұрын
Sorry, I no longer have this model. Maybe these two videos will help: kzfaq.info/get/bejne/mZZ1gLek1rjIg5s.html kzfaq.info/get/bejne/fLmEfLp9qa3UnaM.html
@patrik9434 3 жыл бұрын
Mega Arbeit 👍👍👍☕
@amertahir Жыл бұрын
What cleaning solution did you use (and what ratio did you mix with water) for deep cleaning internal parts. I got a Jura Z5 that was left in a garage I think and it has grime and small dead mosquitoes in the water tank, any suggestions how do I clean it? Also, what spray did you use to clean the inside of the machine?
@gyozoszorgent9248 Жыл бұрын
Nagyon szép munka Gratulálok
@user-vh2xi6qm8m 2 жыл бұрын
Спасибо за подробное видео. Поражаюсь вашей щепетильности, выдержки и вниманию к деталям. Скажите, чем брызгали из пульверизатора когда мыли стенки?
@yt.myworks 2 жыл бұрын
Спасибо за хороший комментарий. В пульверизаторе была только вода и моющее средство ;-)
@irmantasluksa1093 2 жыл бұрын
Ни чем не брызгал. Сами узнайте, протестируйте. А потом скажите. По любому удалитель жира с варочной плиты в этом поможет.
@azamatyusuff Жыл бұрын
ay man I have problem. I assembled everything and then when I finally want to make coffe, it starts pouring the coffe very slowly. it eventually fills the cup but its just so slow like its struggling. can you help?
@yt.myworks Жыл бұрын
Maybe the grinder is set too fine!?
@azamatyusuff Жыл бұрын
@@yt.myworks fixed it by rotating the cog gear inside the grinder
@pisquared1366 Жыл бұрын
Thank you for the detailed video. I have the exact same machine that I took apart the other day and I'm putting it back together now. One question: when you take out the conical rotor grinder underneath are 3 springs and 3 ball bearings. Are there any other similar combinations of springs/ball bearings that you ran into? However meticulous I was in the disassembly, I saw a tiny spring on my workbench that I can't trace back. I'm trying to look at some parts diagrams but they're not as detailed as I would have hoped! Many thanks in advance, greetings from Harvard, MA, USA
@yt.myworks Жыл бұрын
Hello, in the upper part, under the black plastic ring, there is another metal ball with a spring. The ball prevents the grinder from moving again during the grinding process. When turning, the ball makes the typical clicking sound 5:55. Greetings 👋
@pisquared1366 Жыл бұрын
@@yt.myworks You are incredibly helpful and I'm grateful! Thank you....
@tg2451 Жыл бұрын
Great video, very helpful. I know you have a lot of videos, but did you do the usual seal checking and replacement for the rest of the water flow path on this machine, even though the video doesn't show it or is it not necessary?
@yt.myworks Жыл бұрын
On a machine that has been in use for many years, I always replace all the seals, even if they still look good. Above all, however, in the area of the heater where the o-rings are exposed to high temperatures.
@daweiou6315 3 жыл бұрын
Good job
@trixiepickle8779 2 жыл бұрын
Gorgeous machine, super engineering even though 13 years old. Thank you for restoring it.
@coffeetricksandtips1018 2 жыл бұрын
Thx, So usefull video!
@alejandrodvazquez5632 3 жыл бұрын
very good job . a whim of care. to lighten the white plastic which product to use? to polish which paste to use?
@yt.myworks 3 жыл бұрын
@Alejandro D Vazquez Hello, the products I use can be found in the video description below.
@anders2806 Жыл бұрын
I did the same refurbish on a Ena 7. After reassembling the machine the display says "Open tap". Have no clue what to do about it, any ideas? Thx for a great video which helped me in me work.
@yt.myworks Жыл бұрын
Check that all hoses are connected correctly to the flow sensor, the direction of flow of the water is very important. Otherwise the machine thinks that the water circuit is empty.
@ksarm548 2 жыл бұрын
Remarkable restoration. Any idea why a new Ena 8 won't produce hot milk? Cleaned milk system about 8 times, coffee system once. Still no hot milk, barely warm.
@yt.myworks 2 жыл бұрын
Most often the problem lies with the "cappuccinatore" it must be disassembled and thoroughly cleaned. All small holes inside must be free. You can also borrow another part to test if you know a Jura owner. Also try to descale the machine properly, you have to deactivate the filter function.
@ksarm548 2 жыл бұрын
@@yt.myworks thank you for your response. I really have thoroughly cleaned all parts. I did some research and it appears you need to slow the milk flow so it has time to heat up while going thru the system. Jura actually have a 'restrictor' for ena9 but doesn't appear to fit my ena8?. I ordered some replacement milk parts and if that doesn't work I'm going to tweak. Btw, how the *&^%$ do you remember where are the parts go when you dismantle ???? Fascinating, I guess a wiring/parts manual would help. Fun watching the restoration process.
@Elimbar92 7 ай бұрын
Hi there! Awesome video! I probably watched it 5/10 times while trying to repair a Jura ENA 7 Aroma +, which is very similar to this model. I completely disassembled and riassembled the machine. Though i'm now in a bit of a pickle.. I keep having problems with the brewing unit: in already two different occasions, while testing the machine, the silicon tubing located inside the plastic part that slides in the tube with the thread (the part with the brewing sieve) just "explodes" off (it doesn't break) as i try to make an espresso. I changed the 2 big rubber o-ring on, greased everywhere, and that silicon tube as well (all measured). It seems it doesn't hold the pressure or that there is too much pressure. Everything else (for now) seems to work. What are your thoughts? Thanks for any help :)
@yt.myworks 7 ай бұрын
Hello, I recommend checking the brewing group again. I made another video on the subject. There is usually no more water pressure on the outlet hose. That's why you should check everything again on the correct assembly of the parts. kzfaq.info/get/bejne/sJiToaxjzZrWhnk.htmlsi=uBgWuj6FEpKCwqzo
@Elimbar92 7 ай бұрын
@@yt.myworks I did disassamble and assemble the brewing group multiple times. I guess I needed one more :D Don't know what I did differently (I always used that video as ia guide to assemble it) but now it works perfectly! Thanks a lot!
@mixaelization Жыл бұрын
Please make an Imprssa e 70
@TheAriane3 2 жыл бұрын
Will you do it with mine as well?
@nwiegman 2 жыл бұрын
My goodness- will you come to Delaware? To fix- To Repair- To Restore - Divine
@coffeetechph 3 жыл бұрын
Wow. I wish i can make a video like you doing. I have some video on my channel, but not like how you make and edit yours. 😔 By the way, this is very helpful.
@amper121 2 жыл бұрын
Super robota. Mam taki sam i jak zaparzam kawę zaczyna cieknąć woda. Nie wiesz co może być przyczyną? Dodam że jak samą wodę podaje to nie cieknie.
@yt.myworks 2 жыл бұрын
W którym miejscu cieknie, do tacki czy na zewnątrz? Kawa czy sama woda?Pozdrawiam.
@CyberONFire Жыл бұрын
What are you using to polish the black plastic? Got a Jura Impressa z5 where I ruined the silver front of the ground tray in the dishwasher, which I'm trying to find a way to fix
@yt.myworks Жыл бұрын
I'm afraid it can no longer be polished and you will have to buy a new front panel. For the black plastic parts I use Menzerna Polish Set: amzn.to/2PDuE68
@cantthinkofabettername7016 2 жыл бұрын
Very nice video, thanks! I also own an Ena 5 (14 years old) and I would like to clean it and fix some broken parts (the pressure hose started leaking). Could you please tell me where did you buy the replacement parts? I looked online but only found certain parts and also overexpensive. I went once to a Jura shop where they were so nice to sell me a couple of stuff but they said it was an exception. I'd also like to buy a new logo and replace some scratched parts, as well as some hoses, like the one for the coffee as it is now black after 14 years of use.
@yt.myworks 2 жыл бұрын
Hallo, unfortunately the housing parts, water tanks, drip trays at Jura are very expensive compared to other brands such as Delonghi. This is the shop where I buy my spare parts: www.juraprofi.de/Jura-Ersatzteile/Kaffeeauslauf/Button-Jura-31-7mm-fuer-ENA-Kaffeevollautomat::7179.html
@cantthinkofabettername7016 2 жыл бұрын
@@yt.myworks Somehow I'm not getting notifications from yt and just forgot about this and now I've seen your reply. Thanks a lot!
@henryklehnort5678 Жыл бұрын
Pokaż
@fly_green Жыл бұрын
I did this but now it seems like the coffee ground (that gets emptied in to the bin below) comes out sludgy. It seems like the ground coffee is not being compressed properly. Is there a way to adjust this?
@yt.myworks Жыл бұрын
If you assembled the brew group correctly, then it's probably the grinder that needs to be adjusted properly. The coffee powder must not be ground too coarsely or too finely.
@danielm903 Жыл бұрын
Great video! Ganz toll! I have the same machine and my coffee bean lid (the transparent plastic lid) is quite dirty with coffee bean oil (brown/yellow colour). What would you recommend to clean this plastic lid? Thanks/Danke im Voraus!
@yt.myworks Жыл бұрын
Zur Reinigung benutze ich Brennspiritus (methylated spirit). Bekommt man günstig in jedem Drogeriemarkt 😏
@danielm903 Жыл бұрын
At 2:56 min, what kind of screw driver bit do you use? The black screws on mine i have never seen before!
@yt.myworks Жыл бұрын
@@danielm903 Oval Bit: amzn.to/3c1PHIt
@danielm903 Жыл бұрын
Danke vielmals
@danielm903 Жыл бұрын
What tool would you recommend to unscrew the long black tube that i believe is connecting the grinder setting wheel (coarse/med/fine) to the grinder itself? I am trying to remove the grinder but am unable to do so. It looks like a 3.5mm Inbusschlussel but im not surr. Thanks!
@glzbbl Жыл бұрын
sieht von außen wie neu aus, guter Job. Aber dennoch ein Blender, warum: - Schläuche getauscht nach 13 Jahren? > Kaffeeauslaufschlauch auf jeden Fall nicht. es wäre ein EInfaches wenn der Auslaufschieber schon demontiert wird; - Dichtungen getauscht?; - Mahlwerk nutzt sich ab, da hilft auch reinigen nichts, da müssen ggf. neue Mahlsteine rein; - Dichtungen in der Brühgruppe mit ZU viel Fett beaufschlagt > landet im Kaffee. Zudem setzt sich an dem vielen Fett im Nachhinein massiv Kaffeemehl ab. - warum die Empfehlung von kleinen einschichtigen Reinigungstabletten? die 2 schichtigen Tabletten haben ihren Grund. Leichte Dellen im Brühsieb sind vollkommen Problemlos, das Kaffeemehl gleicht das aus;
@yt.myworks Жыл бұрын
wie heißt es so schön, man lernt nie aus ;-). Was die Dellen im Brühsieb angeht, die stören mich einfach. Trotzdem danke für deine Kritik.
@RESTORATIONOFSCRAPMETAL 3 жыл бұрын
Cool 👍
@douwekutschlojenga3482 7 ай бұрын
Hi, using this video i have tried to do the same on my Jura eno9 however after putting everything back together in i think the right way the machine keeps on asking for beans to be refilled even though the beans are there.... anything i missed? thanks for the help! great video!
@yt.myworks 7 ай бұрын
Hello, if you have disassembled the grinder you now have to make sure that it is properly adjusted again. If the grinder is set to too fine or incorrectly, it can happen that too little coffee is ground. The machine detects this and displays an error message "Filling coffee beans". Important: When screwing the long screw in the grinder, make sure that the plastic parts are properly plugged into each other.
@douwekutschlojenga3482 7 ай бұрын
hi when i turn on the Machine and push my choice of coffee then it doesn't even grind one bit...... it says directly on the display that i have to fill the beans....
@yt.myworks 7 ай бұрын
You can try removing the burrs to make sure the grinder isn't blocked. If that doesn't help, then you need to check that the cables are connected properly.
@soniasu6616 Жыл бұрын
I have Jura 4 coffee machine for years and works pretty good. There was a message " Fill beans" and I filled some. But the machine repeats the same message "Fill beans". May you please let me know what I can do? Thanks. I have a video I wish I can send to you. Greeting from CA, USA
@legerdingen Жыл бұрын
When the “fill beans” message keeps showing. Then there is not enough coffee in the brew group. Does the grinder grind normally? Then the spout of the coffee grinder is clogged.
@andrzejgasiorowski4411 2 жыл бұрын
Cześć, dzięki za świetny materiał. Naprawdę szacunek 👏 Mam tylko jedno pytanie - czym odkręcić te czarne śruby z przodu i tylu ekspresu (pod zaślepka z napisem Jura). Mam sporo narzędzi ale nic mi nie pasuje
@yt.myworks 2 жыл бұрын
Również dziękuję! To są specjalne owalne śruby. Bit można kupić na ebayu, amazon lub na innych portalach. Pozdrawiam. Oval Bit: amzn.to/3c1PHIt
@andrzejgasiorowski4411 2 жыл бұрын
Serdeczne dzięki za podpowiedz 🙂 Kupiłem razem z zestawem uszczelek. Od 14 lat używam Jurę Ena5 i czas już aby ją wyczyścić. Sporo kosztował, ale jest bezawaryjny.
@naturaprint987 3 жыл бұрын
I have Jura impressa cappuccinatore. "Please wait. Service required". Any suggestion?
@yt.myworks 3 жыл бұрын
Hello, I found this on the Internet: If the Jura fully automatic coffee machine only shows "Please wait", the device is clogged or has a leak at the back, or the coffee is no longer hot enough, it is often due to the thermoblock.
@henrybroger Жыл бұрын
HELP!! I have a left over part and have no idea where it goes. At 5:24 in to this video I see my mystery piece. It is in the silver tray in the upper center right of the screen with bits of the top of the machine. It is the only black plastic part in that silver tray. I have had no luck finding a parts diagram where I could identify this piece. I have an Jura ENA4
@yt.myworks Жыл бұрын
You can send a picture to my e-mail, maybe I can tell what the part is: yt.myworks@hotmail.com
@stefix6 2 жыл бұрын
Tips for cleaning the spouts? Ours seem to be a bit clogged.
@yt.myworks 2 жыл бұрын
You can try cleaning from below with a small brush.
@jor826 2 жыл бұрын
I have a ena 7 since 13 years, never cleaned it except the flow. My coffee is too light since a few months despite settings "strong coffee" Do you think the problem could be the grinder? Or other ? Or may I try to clean all before? Thank you !
@yt.myworks 2 жыл бұрын
@Jo R hm .. I don't know your machine, so diagnosis is very difficult. Will the cup still be as full as it used to be? It is possible that some of the coffee flows into the collecting container. On the other hand, it is also possible that the grinding stones are already worn out if the coffee beans are ground too coarsely.
@jor826 2 жыл бұрын
@@yt.myworks tanks for answering. I cleaned all the machine whith your instructions. The problem was peaces of coffee into the grinder. All is ok now. Thank you very much again
@vicentemena947 Жыл бұрын
Hola myworks perfectos videos tengo un problema con mi jura ENA 3. Hace un mes en el lector me pide café y está lleno y no me hace cefe ni lo muele ni nada . Y. Es una pena porque hace unos cafés magníficos. Que puede ser ? Perdona el idioma no se inglés soy de España . Gracias un saludo👍
@yt.myworks Жыл бұрын
Hola, que mensaje de error muestra la maquina?
@vicentemena947 Жыл бұрын
@@yt.myworks Hola myworks. en la pantalla delante del rotari .me pone llenar café . Y el embudo está lleno de café . Vi un vídeo de usted hace un año como cambiar .las tóricas del compactador y las cambie IVA perfecta hasta ahora . Que me da ese problema de llenar café. Muchas gracias. A ver si me puede ayudar y lo puedo arreglar yo.👍👏
@vicentemena947 Жыл бұрын
@@yt.myworks se me olvidaba también e desmotado el molinillo lo limpie y las muelas de moler se ven bien y no vi nada desenchufado. No se porque no detecta que tiene café. Y eso me pone llenar café. Gracias un saludo. 👍🇪🇸
@slamerhell 2 жыл бұрын
Большое спасибо за видос , очень помог, помыл , почистил и резинки поменял на заварном блоке , предварительно смазав их силиконом пищевым для кофемашин
@peter_c Жыл бұрын
I have one of these and need to clean. But I also have a leak somewhere. I didn't see the part where you applied the grease and changed the o-rings that you linked. Do you have more info or videos on that? Thanks.
@yt.myworks Жыл бұрын
Hello, which part do you mean, minute? There are many videos on my channel about repairing Jura coffee machines.
@peter_c Жыл бұрын
@@yt.myworks In this video description you have links for OKS Multi Silikonfett/OKS silicone grease, O-Rings. I think these must be used to refurb the brew group, but I don't see those steps in the video. I'm interested since my machine is leaking. on another note, I see some refurbishers say they "calibrate" the grinder. How does one calibrate a grinder? Where does one get new burrs? Any info appreciated.
@yt.myworks Жыл бұрын
There are other videos in the playlist on my channel / kzfaq.info/get/bejne/sJiToaxjzZrWhnk.html
@miriambliss Жыл бұрын
The small black screws have no shape or slit, how to unscrew them?
@yt.myworks Жыл бұрын
Oval Bit: amzn.to/3c1PHIt
@paololeardi337 2 жыл бұрын
BRAVO!!!
@tg2451 Жыл бұрын
Just a question. Do you happen to know how to remove the coffee spout on a ENA Micro 5? I have seen instructions that call for a special tool that as far as I can tell is not available anywhere. It is a spout removal tool. Any words of wisdom about this?
@yt.myworks Жыл бұрын
Unfortunately I don't know, I haven't removed or cleaned a coffee spout from the ENA micro 5 yet.
@tg2451 Жыл бұрын
@@yt.myworks Thanks so much
@nirodha7028 3 жыл бұрын
What specialized ‘bit’ are you using to remove the two black ‘lock’ screws at the start of the video? They have a shape I have never seen before.
@yt.myworks 3 жыл бұрын
Oval Bit: amzn.to/3c1PHIt
@bosroamer 3 жыл бұрын
@@yt.myworks Or you buy a normal key with a hollow shaft, you grind off the beard of the key, then give the shaft a smack with a hammer so it becomes oval and presto, you have your tool
@tg2451 Жыл бұрын
Hello, I have an ENA4 that does not put out any liquid to the coffee spout. I refurbished the brew group, replaced the plastic drain valve cap with an aluminum version, and de-scaled the machine. When it goes through the rinse cycle, it appears the water is coming out of the bottom of the upper piston and flowing directly into the grounds container. The water does not appear to be coming out of the drain valve. I have also disassembled and cleaned all of the tubing from the top of the brew group out through the coffee spout. Water comes out of the tap just fine. Any clue as to what the problem might be?
@yt.myworks Жыл бұрын
It could be that you installed the brewing piston upside down. That means you have to turn it 180° clockwise.
@tg2451 Жыл бұрын
@@yt.myworks thanks for the reply. I checked the orientation of both pistons and they seem to be correct, the riser tube is towards the back of the brew group and the lower piston also has its underside connection towards the back.
@yt.myworks Жыл бұрын
The riser pipe should be directed towards the front of the coffee machine then it is correctly installed. In rare cases it can also happen that the brewing piston has a crack and the water runs out.
@tg2451 Жыл бұрын
@@yt.myworks Thanks again for all of your feedback. I figured out the problem. I had mistakenly put a Micro series o-ring on the upper piston. I replaced it with the right o-ring and everything works. lol!
@jimqu Жыл бұрын
G'day, mate great work .. @7.49 Which liquid did u use to remove coffee stain from chassis or did u repaint the chassis? Thank u for answer in advance...
@yt.myworks Жыл бұрын
Nothing special just dish soap water ;-)
@jimqu Жыл бұрын
@@yt.myworks Can I borrow your magic hands ... mine Jura's chassis stains mark won't go away... Thank u for ur reply now I know why my wife is not happy when I do dishes....
@bartfrederiks5892 10 ай бұрын
Hi @Myworks, excellent video and great work refurbishing that machine! I've been trying to repair an ENA3 but so far without success. When the machine powers up, the electric motor moves up the piston but when it has reached the top position it keeps on going. The gear on the motor then slips on the blocked metal gear - nasty sound! Any idea what might be the problem? Thanks in advance!
@yt.myworks 10 ай бұрын
Hello, try by hand if the brewing group can be easily moved up and down. If not, you'll need to put it back together properly. After that, the brewing group should be brought into the basic position before installation. Make sure that the electric motor fits properly on the long gear.
@bartfrederiks5892 10 ай бұрын
Thanks! I've not disassembled the brewing group, only taken it out of the machine and put it back. When the brewing group is out of the coffee machine it moves up and down quite smoothly (although halfway it briefly sticks a little bit), but when it is back in place the white gear only rotates with force. What is the basic position for the group when putting it back? I tried reinstalling when it is all the way down, but when starting the machine then it will just move it upwards again until the top position and then the motor gear will again slip over the long gear.
@yt.myworks 10 ай бұрын
If the large hole is open, ready to receive coffee powder, then it is the basic position.
@bartfrederiks5892 10 ай бұрын
Hi, me again! I'm pretty sure that I replaced the brewing group in the basic position, but the problem still persists. No matter the position of the BG (basic position, or all the way down), the motor will always just move it up, all the way until the end and then the gears start slipping. I was wondering why the BG would be running to the top at startup, as its basic position is pretty high up to begin with. Isn't it supposed to run downwards from the basic position?
@yt.myworks 10 ай бұрын
The brew group moves up and down to find the home position, which it does every time the machine is turned on. When inserting the brewing group, make sure that there is no gap between the electric motor and the brewing group.
@OL-ss8ur Жыл бұрын
Hey man, could you help me please? What is the name of screwdriver , you used it for removing a plastic from back? Thank you
@yt.myworks Жыл бұрын
Oval Bit: amzn.to/3c1PHIt
@OL-ss8ur Жыл бұрын
thanks! it's very tricky to make such bolts. 😊Another question, for my taste, the coffee that the machine brews is not very strong, do you think if i adjust the grinder so that it grinds finer, will it help? And what grinding should be, size?
@vladodimi8247 2 жыл бұрын
Hey, what kind of tool you use to loosen the bolt on 2:55?
@yt.myworks 2 жыл бұрын
Oval Bit: amzn.to/3c1PHIt
@wojtek2194 2 жыл бұрын
cześć, gdzie można znaleźć informacje w którym roku została wyprodukowana dana sztuka ?
@yt.myworks 2 жыл бұрын
Witam, na wielu plastykowych częściach znajduje się wytłoczona pieczątka z datą produkcji. Zazwyczaj rok i miesiąc który zaznaczony jest strzałką.
@bkbaby347 11 ай бұрын
Hey @myworks ! Thank you for your amazing videos. I have jura ena micro 1 , the water pump was bad , replaced it and the pump only works when I turn off or some times on as the cleaning cycle but when marking coffee the pump doesn't turn on . I know the pump is good since when it gets Power it pushes water. Do you have any idea what could be the issue?
@yt.myworks 11 ай бұрын
Hello, you need to make sure that no water pipe is clogged. Is the water pump audible when making coffee?
@bkbaby347 11 ай бұрын
@@yt.myworks hey, no clog in the pipes because when the machine turns off it goes through the spout rinsing cycle. And the pump is audible when the rinsing cycle Is on and a good flow off hot water comes out . But when I request for coffee the pump doesn't kick in . I wonder if it's a sensor throwing it off . I opened the flow meter and cleaned it , it was clean inside and the magnet wheel spins freely. Do you know of any sensor that would prevent the pump from turning on ? There are no errors either. Goes through everything fine , Brew group is working, heater. It's just the pump that won't turn on at that coffee call state. One thing I forgot to mention is that the coffee grinder burrs are done and don't grind. Is it possible that the pump won't kick in but will go through the coffee cycle because there is no powder ?
@yt.myworks 11 ай бұрын
@@bkbaby347 Without coffee powder, the machine interrupts the process. Try using an already ground coffee to test if everything works properly.
@bkbaby347 11 ай бұрын
@@yt.myworks thank you, I will try that . I think the coffee burrs are done , when I received the machine the grooves were totally blocked and had some corrosion and discoloration, also might be missing a top part that encloses the beans ,I'm not sure because I cannot find a picture of the bean grinder. I will report back soon
@yt.myworks 11 ай бұрын
@@bkbaby347 In my other video you can see the grinder in min. 6;30. This is something different, but similarly structured kzfaq.info/get/bejne/hslmZqan2Kyben0.html
@ritavanderpol-modderkolk3857 Жыл бұрын
Can you please come over to clean mine? 😉😀
@LublySchawell 3 жыл бұрын
Why don't you polish the metal cup holder on the pallet? Thanks in advance for your reply.
@yt.myworks 3 жыл бұрын
Hello, polishing the sheet metal takes a lot of time that I don't have. A new one costs about 20 €. But it can certainly be polished well.
@LublySchawell 3 жыл бұрын
@@yt.myworks Then maybe you can advise how this can be done? What tool to use, polish and polishing disc. I would be very grateful for your advice.
@yt.myworks 3 жыл бұрын
Hi, you need very fine sandpaper in various grain sizes and a good polishing machine. I recommend videos on KZfaq dealing with metal polishing.
@robertjaszewski3568 3 жыл бұрын
Jak zawsze uczta dla oczu. Chochlik też był wyczesany :o)! Zapomniałeś Bruder wymienić szlauch między zaparzaczem a wylewką. Powinien być on chyba przezroczysty ;)? Podpowiesz jakiego w Niemczech środka do czyszczenia plastiku szukać ( nazwa lub skład)? Pozdrawiam i życzę kolejnych inspiracji do prezentacji.
@yt.myworks 3 жыл бұрын
Dzięki za komentarz. Środek czyszczący to zwykły utleniacz do włosów, nie mam pojęcia jak sie to poprawnie nazywa. Linki do produktu znajdziesz w opisie pod video. Pozdrawiam.
@robertjaszewski3568 3 жыл бұрын
@@yt.myworks Utleniacz? Hehe. Czasami proste rozwiązania są najlepsze! Ja ostatnio malowałem srebrne elementy maszyny sprejem do Alu felg, odcień jest identyczny i po co kupować nowe elementy..? Czasami warto.
@patafterhours6172 2 жыл бұрын
Hi mate, I get one of the jura coffee machine lately it doesn't form the coffee pucks correctly. Did you came across that issue I am assuming that grinder might need new mill and ring. I did clean and adjust the grinder, no luck.
@yt.myworks 2 жыл бұрын
The Jura coffee machines do not make pucks as firmly as, for example, Delonghi machines. It is important that the pucks are not too wet and that the grinding degree is set correctly. The coffee must therefore have a good crema and taste.
@patafterhours6172 2 жыл бұрын
@@yt.myworks In my case pucks are not existing at all it is just grounded wet coffee.
@yt.myworks 2 жыл бұрын
Can you send me an Pictures from the puck to my e-mail address. Maybe I can give you a tip.
@patafterhours6172 2 жыл бұрын
@@yt.myworks done mate, thanks
@mguerramd 2 жыл бұрын
When I changed the grinder burrs on my F7, and overhauled the brew group, I started getting nice firm pucks.
@randommusings48 2 жыл бұрын
Why did you changed the milk tube at 18:40?
@yt.myworks 2 жыл бұрын
I used a new, better quality hose
@soniasu6616 Жыл бұрын
Can you please tell me what is the size of the socket at 2:25 minutes, Where I can buy it? Thank you so much!
@yt.myworks Жыл бұрын
Oval Bit: amzn.to/3c1PHIt
@soniasu6616 Жыл бұрын
@@yt.myworks I used ground coffee for a month. Suddenly the machine stopped working and showed "Please fill up beams" . I put coffee beams in but the machine still show "Please fill up beams" . Can you please let me know what I can do? Thank you so much! Greetings from California USA
@yt.myworks Жыл бұрын
Hello Sonia, that happens when the grinder does not produce enough coffee powder. It may mean that the grindstones are blunt. Through the filling opening you can observe how much powder gets into the brewing group during the grinding process.
@tobipista4275 Жыл бұрын
Hello from the hot water the water coming out but where the coffe comes out no caffe whit no water
@yt.myworks Жыл бұрын
If the coffee ends up in the drip tray then this is usually the problem kzfaq.info/get/bejne/bsmoaZOXtbe0cps.html
@Michelangelo121984 2 жыл бұрын
Sehr schön......!
@michaelklapdor8897 3 жыл бұрын
Super Arbeit. Bin echt begeistert !!! Sollte man für diese schwarzen Kunststoffteile alle drei (Schleifpaste bis normale Politur?) nehmen oder reicht das "Super Finish"? Habe eine Ecam 22.110 B (schwarz), die ebenso eine solche Auffrischung bräuchte (ReinigungsKratzer usw.)...
@yt.myworks 3 жыл бұрын
@Michael Klapdor: Danke für den Kommentar. Ich empfehle die Körnung "2.500" und anschließend "Super Finish". Aufpassen, nicht zu lange auf einer Stelle polieren. Verchromte Schriftzüge unbedingt auslassen und über die Piktogramme nur leicht mit dem Super Finish. LG
@dimsler7934 2 жыл бұрын
Requires a deep clean like the one shown once per year, as per Jura specification.
@yt.myworks 2 жыл бұрын
@Dimsler I recommend cleaning the brew group every two years.
@pierotez 2 жыл бұрын
Witam! Chcę zregenerować zaparzacz w Enie 7 bo już ciężko chodzi i czaszami stanie. Procedurę znam, już to robiłem. Wymienię wszystkie uszczelki, nasmaruję gdzie trzeba silikonem. Wielka prośba jakiś środków używasz do czyszczenia? Do grupy kupiłem proszek Puly Caff Powder ale nie wiem ile go rozrobić z wodą. Do czyszczenia środka użyłeś jakiegoś płynu z spryskiwacza a do tacek jakiegoś żelu. Prosiłbym o poradę. pi
@yt.myworks 2 жыл бұрын
Część, do czyszczenia części używam sody oczyszczonej (natron), a Puly Caff to jej ulepszona wersja. Natomiast do tacek zastosowałem utleniacza w stężeniu 12% który jest w stanie wybawić plamy po kawie. Jednak działa to tylko na jasnych platikach i pod wpływem światła UV. Pozdrawiam
@pierotez 2 жыл бұрын
@@yt.myworks a czy 6g Puly Caff wystarczy na litr wody? Tak podają w internetach.
@pierotez 2 жыл бұрын
Ups, 10g / 1l.
@yt.myworks 2 жыл бұрын
@@pierotez Dwie lub trzy łyżeczki do herbaty wystarczą. Tak zaleca producent sody oczyszczonej, przy puly caff będzie napewno podobnie. Ważne żeby zostawić wszystko w roztworze ciepłej wody na parę godzin. Uważaj na drobne części, szybko można coś zgubić.
@pierotez 2 жыл бұрын
@@yt.myworks Fiu, na parę godzin! Myślałem że na 20 min. Tak zrobię. Miałem error 8 - czyli zaparzacz chodził góra-dół. Ale to po tym jak ostatnio zajrzałem do środka, usunąłem łopatkę która odpycha fusy i zapomniałem zamontować spowrotem. Teraz wszystko rozmontowane i czeka na mycie i uszczelki.
@kkustosik 3 жыл бұрын
Co to jest za środek którym wyczyaciłeś tacki i ociekowe?
@yt.myworks 3 жыл бұрын
Utleniacz 12% i słońce około pięciu godzin.
@kkustosik 3 жыл бұрын
@@yt.myworks witam cie ponownie i dziekuje za poprzednia odpowiedz. Powiedz proszę gdzie mogę dostać taki utleniacz? I jeszcze jedno pytanie, gdzie mogę kupić taki przyrząd do polerowania plastiku? Qszedzie go szukałem ale nie mogę trafić..
@yt.myworks 3 жыл бұрын
@@kkustosik Do polerowania możesz użyć zwykłej wkrętarki akumulatorowej z odpowiednią nasadką. Dostaniesz za grosze w eBayu. Utleniacz kupiłem na amazonie, nie musi być tej samej firmy ważne jest ile procetowy. Uwaga, to środek chemiczny i należy zachować ostrożność!
@kkustosik 3 жыл бұрын
@@yt.myworks super.. dziekuje za wskazówki.. ja teraz idac za Twoim przykładem doprowadzam do perfekcji jure F8 no i szukam różnych specyfików ktore pomogą mi w tym. A za renowacja czeka jeszczec13 sztuk. Wiec rady naprawde sa cenne.
@alibabawelkom6302 3 жыл бұрын
👍👍👍
@FinnTheMilky 11 ай бұрын
Hey mate, im in the process of restoring my ENA 5 also, do you add grease to any slides points or Orings?
@yt.myworks 11 ай бұрын
Hello, the O-rings are always greased by me, everything else as needed, as seen in my other videos.
@maxfactor4209 3 жыл бұрын
Never seen this much of injection plastic in my life ..
@RuJewi 9 ай бұрын
This is only cleaning without repair or refurbishing. You had to replace the grindstones, had to change the silicone tubes, had to clean the dispenser. You didn't do anything
@Mister_Michael 9 ай бұрын
and what did you accomplish besides typing this comment?
Well done. Мастерская по ремонту кофемашин.
Рет қаралды 2,6 М.
Friendeez
Рет қаралды 19 МЛН
Кофемастер
Рет қаралды 51 М.
Retro Tech & Electronics
Рет қаралды 72 М.