KA24DE Detailed Assembly - Start To Finish

Рет қаралды 24,768

2 жыл бұрын

Step by step 240sx Ka24de Engine dissasembly and refresh including intake manifold cleanup, timing chain and ignition timing the distributor
Instagram
/ nscardigno
*Molded rubber hoses
Thermo to intake 19043
Bypass 71544
Iacv 28460
Heater core 18774
Heater core 19049
Chapters
0:00 -
0:05- acc removal
2:26 - intake removal
4:40 - pressure washing
5:45 - cover removal
7:07 - setting tdc
8:11 - lower guide / timing tensioner install
9:35 - timing comp. torque specs
9:43 - verify mechanical timing
10:14 - timing chain diagrams
10:37 - timing cover install
11:55 - front cover torque specs
12:25 - oil pan install
13:07 - under intake heater hoses
13:23 - intake manifold refresh
16:23 - intake manifold install
17:17 Distributor timing
18:39 clutch assembly
19:20 flywheel / clutch torque specs
-Sunset drive
Sunset Drive by Tokyo Music Walker
/ user-356546060
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/3wsYF7Z
Music promoted by Audio Library • Sunset Drive - Tokyo M...
3:51
-Summer time
Summertime by Tokyo Music Walker / user-356546060
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/al-summertime
Music promoted by Audio Library • Summertime - Tokyo Mus...
7:58
When I Was A Boy by Tokyo Music Walker
/ user-356546060
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/when-i-was-a-boy
Music promoted by Audio Library • When I Was A Boy - Tok...
11:00
It Will Be Alright by Tokyo Music Walker / user-356546060
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/-it-will-be-alright
Music promoted by Audio Library • It Will Be Alright - T...
15:00
Colorful Flowers by Tokyo Music Walker / user-356546060
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/al-colorful-flowers
Music promoted by Audio Library • Colorful Flowers - Tok...
19:00
My Itinerary by Tokyo Music Walker / user-356546060
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/t-w-my-itinerary
Music promoted by Audio Library • My Itinerary - Tokyo M...

Пікірлер: 114

@dreednlb 2 жыл бұрын

Very well done. The KA community has been needing a video like this.

@Nscardigno33 2 жыл бұрын

Thank you for watching! Good to hear it’s helpful

@StephenStrappJr 2 жыл бұрын

Yassss! This is what we were talking about. People are gonna watch and build at the same time with such chill vibes with the music. Ka Build: Step 1: Be Nick. Step 2: Engines done. Magic.

@Nscardigno33 2 жыл бұрын

Thanks dude I can feel myself getting better every video . 😂😂 1.5hrs condensed to 20mins

@FriedEggsandJellyfish 4 ай бұрын

Coming back to this video again 2 years later. Those part numbers are a time saver!!! Thanks dude

@ramonesfreak2010 Жыл бұрын

I needed this as i’m assembling my KA. Thank you!

@zachwebb3875 Жыл бұрын

Same

@KlutchKickers 2 жыл бұрын

Great video!! I will be refreshing my KA using this video🔥🙌🏽

@daltongriffis Жыл бұрын

Awesome video man! Love the editing and the attention to detail

@Nscardigno33 Жыл бұрын

Glad you enjoyed it!

@zmcreations1575 2 жыл бұрын

Killing it man this is really detailed 👍🏼

@Nscardigno33 2 жыл бұрын

Thank you for the feedback ☺️

@boatx22 Жыл бұрын

Thanks for this

@ArnoTrek 8 ай бұрын

Wow. The intake related stuff is going to take awhile to sort out. The rest looks pretty straight forward. 12mm swivel socket has just been ordered. Thanks for putting this up.

@Hiighboost2 5 ай бұрын

I liked and subbed many years ago, but don't know if I ever left a comment. Thank you for all the effort you put into making this video! This is my type of how to video. Showing how you do it in real time. This is extremely useful to anyone needing to work on these KA's.

@Hellcatsinner 2 жыл бұрын

This is the Greatest Auto shop dream video of all time

@Nscardigno33 2 жыл бұрын

This makes me excited to get better and make more

@AustinTillison 2 жыл бұрын

thank you!!!

@joshuapatterson4148 2 жыл бұрын

Another soothing video with a guest appearance by M18 power! Added to the playlist.

@Nscardigno33 2 жыл бұрын

Little do you know I’m editing these specifically for you

@ChrisN85 2 жыл бұрын

Awesome video, very informative!

@Nscardigno33 2 жыл бұрын

☺️

@-theodds 2 жыл бұрын

Beautifully done👌🏼

@Nscardigno33 2 жыл бұрын

🥰🥰

@angustulloch6939 Жыл бұрын

Thank you 🙏 you’re my hero

@Nscardigno33 10 ай бұрын

anytime

@duffledawg2928 2 жыл бұрын

The ka24 is becoming so popular these days. Thanks for the post!

@Nscardigno33 2 жыл бұрын

No problem more ka stuff to come I put a lot of stock cars together

@waltercartagena5830 Жыл бұрын

Very good job and very quick

@Nscardigno33 Жыл бұрын

I appreciate it thanks for taking the time to watch and compliment 🙏

@bronco35 8 ай бұрын

Thank you because I’m gonna totally rebuild the KA in my car and actually add good power and this video is awesome! Keep up the good work!

@Nscardigno33 8 ай бұрын

Glad I could help!

@aharxn 2 жыл бұрын

Great video I really needed this putting a dual cam in my single cam car

@Nscardigno33 2 жыл бұрын

🙏 thank you. wiring is pretty simple .. Just need to swap dash plug to brown dohc and match the colors. Wiring:1. Locate the body harness (under dash harness that attached to the ECU) that attached to your old harness. Cut the old connector off (the one that attached to your SOHC harness) and attach your DOHC body harness connector. Just match the colors!Yellow/Red --TachYellow/Green--SpeedometorOrange--Ignition startBlack---GroundBlue/Black---Water temp sensor

@cuhraw 2 жыл бұрын

AutoShopDream with another work of ART

@Nscardigno33 2 жыл бұрын

Already editing next weeks video 🥰

@ollinium2204 2 жыл бұрын

Nicely done

@Nscardigno33 2 жыл бұрын

🙏 thank you

@zachwebb3875 Жыл бұрын

Supppper helpful video

@Nscardigno33 Жыл бұрын

🙏 glad it helps

@bm2409 2 жыл бұрын

amazing video! thanks!

@Nscardigno33 2 жыл бұрын

Thank you for watching !!

@bm2409 2 жыл бұрын

@@Nscardigno33 are the heater hoses all the same for s14 as well? im doing a refresh on my KA al new seals and removing emissions but want to keep heater and ac...

@Nscardigno33 2 жыл бұрын

@@bm2409 under the intake manifold yes they are all the same

@Nscardigno33 2 жыл бұрын

@@bm2409 now for the intake manifold to the heater core you’ll need Gates part number #19049 And gates part number #18774

@Nscardigno33 2 жыл бұрын

@@bm2409 they are not 100% direct fit but if you trim the right sides down they will fit perfect

@TAC40_ Жыл бұрын

I want you to rebuild my ka as well lol

@Hellcatsinner 2 жыл бұрын

Nahhhhhh ima need you to do every task on the 1989-2002 Nissan production line now in this format

@Nscardigno33 2 жыл бұрын

We just getting started ☺️

@aky280 Жыл бұрын

I have an all OE 92.

@tonyt9537 Жыл бұрын

FYI the oil pump seal is on the wrong way @ 10:46. I hope you removed it and put it in the timing cover collar facing inside the pump

@Nscardigno33 Жыл бұрын

This engine now has another 40k miles on it since the refresh . It will seal either way . I’ve done it both ways as I’ve disassembled original engines and found them in this configuration also

@jlayzi 5 ай бұрын

Hey boss, dont know if you will read this, but im tackling rebuilding my first ka right now, and when i dissembled i cut alot of hoses and lines on the intake manifold, wondering where you are supposed to source those?

@berserkami 6 ай бұрын

I'm struggling to find any info on the oil pump seal in the service manual that you mention at 10:48 - do you have a part number?

@assinspector1391 Жыл бұрын

can you do the same with the single cam?

@kurtlan4636 Жыл бұрын

I have to replace the PVC Valve(rubber grommets) when I replaced the PVC, is between the PVC and breather separator, the rubber vale was so bad and crumble, most of pieces was fall into the breather separator, I didn't take them out before I replaced the new PVC, This this matter?

@miaouchat495 2 жыл бұрын

What hose did you use for the PCV valve? In particular, the one piece that goes from the PCV valve to the distribution tube. The hoses are insanely expensive at the dealership.

@Nscardigno33 2 жыл бұрын

It’s a 3/8 hose I just use some thick wall fuel hose hose for it so it doesn’t kink. Or walk in back of oriellys and match up a prebent 90 at parts store

@abewright4584 Жыл бұрын

What did you do for heater core lines?

@jlayzi 5 ай бұрын

how are you capping the ports?

@braxtonball5535 2 жыл бұрын

The elevator music makes this perfect.

@Nscardigno33 2 жыл бұрын

I got some more tunes otw

@Theferg1 Жыл бұрын

Great video bro!! hey, do you have a link to the FSM thanks bro hey also would you recommend deleting the EGR? Thanks

@Nscardigno33 10 ай бұрын

forums.nicoclub.com/240sx-fsm-full-service-manuals-s13-s14-ka24e-ka24de-t311075.html also I'm working on a partner ship with a company that sells paper back version of the fsm should be ready soon let me know if your interested

@LoganNewlin 7 ай бұрын

Can I get that FSM link by chance?

@stephanielopez4996 Жыл бұрын

Great video! Where did you buy some of your parts??? @AutoShopDream

@Nscardigno33 10 ай бұрын

I use rock auto quite a bit most oem parts are discontinued

@alexxxdagrrreat 2 жыл бұрын

Could I reference this video for a 2002 Nissan frontier xe ? My dad just gave me one 285k miles M/T 4 cylinder.... After a year of sitting I started it up and nothing but blue smoke and failed air compression ratio.... I doubt it's a ka cause I saw mexico stamped ... But it is a 2.4... ? Any advice would be great.

@Nscardigno33 2 жыл бұрын

Sorry for late response I missed this . To an extent yes but the frontier Ka is a bit different as far as hose routing, intake manifold design and distributor location

@justinlassiter7671 Жыл бұрын

awesome vid. Where did you get that Tstat without a jiggle valve? would be grateful for a PN.

@Nscardigno33 Жыл бұрын

oriellys doesn’t stock ka thermostats no I either get them from autozone (Murray brand) or rock auto not sure where this one came from

@justinlassiter7671 Жыл бұрын

@@Nscardigno33 ive been looking for one without the valve and can't seem to find one. searches always yield stats with it. I want one that is set at 180 without the valve

@Nscardigno33 Жыл бұрын

@@justinlassiter7671 to be honest I may have cut the valve off it myself I do that sometimes

@justinlassiter7671 Жыл бұрын

@@Nscardigno33 yeah, I've clipped and drilled them in the past. I don't like them because it increases warm up time. I plug them by bending the valve shut and the engine reaches temp in like 3-4 minutes. I checked Rockauto and they do have the 76.5 without the valve, but even better, they have an 82C with a jiggle so I bought that and will plug it. Thanks a ton for the reference brotha

@SnowsBrain 2 жыл бұрын

Is there supposed to be a hat seal in the block as well as the lower timing cover/oil pump or just the 1 in the block?

@Nscardigno33 2 жыл бұрын

Just one in the block

@SnowsBrain 2 жыл бұрын

@@Nscardigno33 cool thanks 🤙

@slgelite92 9 ай бұрын

What was the house you were using that was wrapped up and we’re cutting up?

@slgelite92 9 ай бұрын

Hose*

@Eman-xz4pr Жыл бұрын

What size was the spool of hose you were cutting?

@Nscardigno33 Жыл бұрын

5/16

@YourUnwantedFriend 4 ай бұрын

I've never seen emissions stuff on a KA 😂

@Nysmo420 2 жыл бұрын

So I've got a problem, i was told my Ka has silicone inside the engine, they said its not gonna run if they swap it over, will i have to rebuild it or should I just run it and let it burn off?

@Nscardigno33 2 жыл бұрын

that sounds crazy I dk how silicone could get in the engine or how they would know there is . unless someone did a poor job resealing it and used too much rtv . in that case just pull the front cover off clean and reseal

@Nysmo420 2 жыл бұрын

@@Nscardigno33 i probably guess the engine guy didn't care too much about the motor since he said it's pretty much an easy engine to work on, but i found someone else to do a rebuild and they told me they will completely refurbish all the parts to get my engine in tip top condition 👌

@TheRealOmniMan777 Жыл бұрын

What kind of pressure washer are you using?

@Nscardigno33 10 ай бұрын

harbor freight lol

@namelast4606 2 жыл бұрын

What gasket kits is everyone using?

@Nscardigno33 2 жыл бұрын

I’ve always had good luck with felpro gaskets as most of this engine is sealed with rtv

@aky280 Жыл бұрын

How did you remove the injector caps?

@Nscardigno33 10 ай бұрын

I've got an ls2 s14 build otw

@soychinoloc 2 жыл бұрын

What pressure washer you have?

@Nscardigno33 2 жыл бұрын

Harbor freight 😂

@soychinoloc 2 жыл бұрын

@@Nscardigno33does it actually work good debating on getting one or a sunjoe?

@Nscardigno33 2 жыл бұрын

@@soychinoloc it’s been working good for me

@s13_shawn Жыл бұрын

Bruh need help I did the egr delete took everything out expect the hard lines under the intake the car starts revs its self to 2k rpm’s then bogs and shuts off. 4 hard lines in the back are still open and not capped and 4 hoses up front only one t’s off to the intake. I have a dual cam ka

@Nscardigno33 Жыл бұрын

Okay then cap them or remove them you only did half the job

@s13_shawn Жыл бұрын

@@Nscardigno33 okay I’ll try that and thank you yeah I would’ve capped all but the pack of caps I bought only 2 were small enough

@s13_shawn Жыл бұрын

@@Nscardigno33 plus I figured since they aren’t connected upfront they wouldn’t need to be capped

@Nscardigno33 Жыл бұрын

@@s13_shawn they don’t all need to be capped but without knowing what you did it’s better to cap them all. The proper way to do this is with the intake manifold off

@s13_shawn Жыл бұрын

@@Nscardigno33 yeah I’ll end up taking it off if that doesn’t work