Thank you for your kind words. Someday I plan on building a workshop not just so I can have room to work on my projects but to also offer up a space to help tech people how to do all sorts of stuff. But until than I’ll continue to utilize the resources I have. Thanks for watching.

You’re welcome. I to originally had that same issue. Took me a little while to figure it out. One of the reasons I made this video.

I'm in the same situation. Lol.

I use an old extension I don't care about whose cable I've split! This way you don't have to split every appliance's cable when you want to test them. Especially handy for stuff where the two wires are into a full sleeve and not easily spittable

@@MattCantSpeakIt -good idea thanks.

Yep same

How exactly do you use it?

I don't understand your comment..He was just measuring the flow

YES but really been 36 yrs more u use like anything u going to look and do better each time get rid fumbling , symbols , use car s everywhere , we have lot DC motors ,actualy i fool people think lm smart no just have good memory , SAFETY FIRST ,

@@flyboybbq1718 yes I realized that mistake a long time ago haha. Sadly I lost the files I used to make this video when my computer cashed years ago. I have been thinking about remaking this video but just haven’t found the time to do that. Thanks for watching.

@@MAGSHowToVideos Sorry to hear that you lost the files. Big picture: anyone will understand your meaning.

That’s weird I had 1080p available for this video. Thanks for pointing that out I’ll have to look more into why it’s no longer an option.

@@MAGSHowToVideos it is as an option and it looks like 240p or less. It's terrible.

@@thomasstambaugh5181 I sold this clamp meter last year. If I can remember, I believe it was part of the “Live Wire” or low/high power reader that allowed you to detect if a wire was “Hot” (had power).

@@MAGSHowToVideos : Sounds like a lead for an "NCV" measurement -- "Non Contact Voltage". I appreciate the quick response!

thanks man

Depends on what you are trying to test in you stove.

The bottom element.

Easy. What you will have to do is remove the element and set your multimeter to your lowest setting for Ohms. If you only have one setting that’s ok. Touch one of the test leads to each end of the element. Test for continuity. If you don’t have continuity then you need to replace the element. If you do than you should get a rough reading of 30-100 ohms. If your reading is higher than that… there might be to much resistance and most likely will have to replace the element. I might put together a video on how to do this. Hope this helps!

Thanks

@@MAGSHowToVideos I also check for grounded element by touching one lead to the outer sheath of the element and the other to the power terminal.

Hahaha ya I didn’t even notice I was saying that until someone else pointed it out after I posted this video.

The clamp portion on a clamp meter can only measure Amps. You would still have to prob the wires to test for voltage.

@@MAGSHowToVideos thank you very much for the response.

You won’t get a proper reading… will most likely display “OL” on the screen since the measurement is to high to properly be displayed.

Couldn’t say it better myself… safety always comes first and if you’re someone without common sense this is not for you haha

High temperature, as in when he's roasting his lead wires over the toaster elements?

Hahaha ya don’t repeat that. Usually I’m all about safety, however, this video was requested by a Subscriber so I quickly put this together in 30 mins not realizing the wire.

I’m so glad I was able to help. It always makes my day when someone leaves a comment letting me know that my hard work has benefited someone. Thanks for watching and Subscribing!

If you are trying to use the clamp, you have to have the wires split. Only one wire can run through it or you will not get a correct reading.

@@MAGSHowToVideos wow! Thank you so much for your help! I really appreciate your channel!

Hahaha I didn’t even notice I said it like that. After years of having this video posted your the first one to point that out. Good job!

Yes I didn’t notice that when I was filming. I usually am all about safety. This video was requested by a viewer so I sort of rushed putting it together and clearly I wasn’t aware of my surroundings.

@@MAGSHowToVideos mmm,,ohh ok, do stand in the corner with a pointed hat,,for a bit, a video on that would be awesome LOL

Care factor zer0, its not like the wires were bare ffs.

That means you have continuity. The long beep means you are just holding the test leads against the wires and haven’t broken contact. The reason for a short beep in my video is because I just touched the wire quickly then took the test lead off.

Good question. The reason you want to test for Currant is so you can make sure you are getting the correct amount of Amps. Even if you have the correct voltage, if you Amp output is lower than what your device is rated for, you won’t have the power need for it to operate properly. I hope this answers your question.

Hahaha ya I meant to say alternating current.

Hahaha ya to be honest I didn’t even realize I said it that way until someone pointed it out to me last week.

This was a requested video from a subscriber. I literally filmed, edit and up loaded this video within like 45 mins after the request. It was for sure a rushed video. You can also see the wire hanging over the toaster which isn’t the safest thing. For the blinds well I rent the house so I don’t feel like spending my own money to replace them. I did just drop $3K on a new camera and accessories so hopefully future videos will look better.

Ya I know… this video was sort of a rushed job since some have requested it that same day.

I am? How so? If there’s a easier way I could have made this video I would love the hear it so I can improve on future videos. This video was rushed (put together and uploaded in 1 hr) since it was requested by a follower, but I think it came out simple and easy to understand. Again would love some feedback if you have any. Thanks for watching.

@@sandorebussolini you do know the whole point of using a clamp meter is to read Amps right? If you are trying to learn how to test for Voltage you can check out my other video “How to use a Multimeter for beginners” in that video I show the basics on how to test for volts, amps and ohms.