No video
Key Immobilizer and Remote Programming Using Toyota Techstream Software - Toyota / Lexus
Рет қаралды 450,392
Күн бұрынHere's how to program a new Lexus or Toyota key immobilizer and remote to work with your vehicle.
On newer model Toyota or Lexus vehicles built in the past decade, programming a key requires Toyota's Techstream software. It can no longer be programmed manually using the "pedal dance" method demonstrated here:
• Toyota / Lexus Remote ...
A spare blank master key was purchased from eBay. Since a blank key cannot be inserted into the ignition, its remote and transponder was gutted from the key shell and inserted into the original master key's shell for programming.
Toyota's techstream software uses a special cable to connect to the OBDII port and communicate with your vehicle's ECU. For a demonstration, see this video:
• Toyota Techstream Soft...
Once the key is inserted and turned to the ON position, the key transponder wizard is opened in the techstream software.
Follow the wizard to reinsert the original master key, then remove it, then insert the new blank key, waiting 75 seconds for it to be programmed. The key will then be programmed for the engine immobilizer, though the remote will still have to be programmed separately.
To program the remote, you don't need Techstream software.
Simply follow the instructions to open and close the door a few times and turn the key in the ignition to put it into programming mode. Then press and hold the buttons on the remote and the locks will cycle indicating it has been programmed.
The eBay key purchased worked fine for starting the car, however the remote proved to only work intermittently, so buyer beware. Its better to buy a cheap key shell with a blank blade and a used OEM remote and reprogram it for your car than to use the aftermarket transmitters which are hit and miss.
Link to Etsy shop where you can purchase speedkar99's brother's socks, t-shirts or hoodies:
www.etsy.com/c...
Check out the speedkar99 Facebook page:
/ speedkar9
Check out the speedkar99 Linkedin page:
/ speedkar99
Follow speedkar9 on Instagram for behind the scenes coverage:
/ speedkar9
Subscribe for more videos just like this:
www.youtube.co...
@adamo36532 3 жыл бұрын
DUDE, you are the first one to point out that the transponder is in the beeper that unlocks the car remotely. I thought it was located under some plastic somewhere. 1:27 saved me from having to buy a cable to use Techstream. I was able to put it next to my old blade off my master key that wouldn't start because I never had the transponder next to it lol. Great video. I just want to tell the viewers that you do not need to use Techstream if you have your master key from before. Ignore every other video if you have a 2004 Lexus es 330 on how to program the transponder. You go in your car with all the doors closed. Next , stick your master key into the ignition 5 times leaving it in at the end. Never turn the key just put it in and out in the off position. Then you open and close your driver side door 6 times while the key is in the ignition. Then you take out your master key (The red security light located under the radio display should not be flashing but be glowing red at this point). You then put your new cut key (The one that you are trying to program the transponder) into the ignition and leave it in, not turning it at all. The red light will start blinking. After around one minute the red light should turn off completely. This indicates that your key has been successfully programmed. You may then take your key out and use it as needed to start your engine. I would recommend pinning this comment to help people
@Kai__S 7 ай бұрын
I can’t for the life of it get my (new to us) 2005 ES330 into key programming mode with the 5 key inserts and 6 door openings. Same with an alternate procedure of hitting the gas pedal 5 times and the brake 6 times. I have 2 reportedly original keys for the vehicle (one with remote fob and 1 without). Might both these keys not be “masters”, like the valet key+card ? Is there a way to tell? My Autel 806 Pro unfortunately doesn’t program keys 😢
@adamo36532 7 ай бұрын
@@Kai__S My valet key is a silver one instead of black and had no remote unlock and I was trying to program with it. I think its different than the other ones because it wont unlock the glove compartment and apparently doesn't have the chip in it that can program new keys. I used the broken original master key to program 2 new keys with the beep unlock. There is a chip inside them that wont start the car unless you activate them using the master key. So when you cut a new key without programming it wont start the car. I am not sure if the new programmed keys can program new keys. Maybe the keys you have were created when the previous owner lost his keys and used a locksmith and then those 2 keys cant make new ones? I am not sure though. When I realized I was using the valet key and finally tried with the master it was really easy.
@chriswilson8678 8 жыл бұрын
Thanks for this great tutorial...just bought my daughter a used 06 ES330 but the remote wouldn't lock/unlock the doors...followed your instruction in the last half of the video and now the remote lock & unlocks like new!...and now I'm the best dad ever! Thanks again!
@speedkar99 8 жыл бұрын
+Chris Wilson Glad you got it working, enjoy the ES. I have a 2005.
@blacksun496 5 жыл бұрын
Chris Wilson did you use a text screen cable or whatever he called it? I have no idea what that is!!
@kickbuttowski8201 3 ай бұрын
It's techstream cable Also know as obd2 cable @blacksun496
@Captain_911 2 жыл бұрын
The best auto mechanic in the world. I will be watching every single your videos. Easy to understand and very helpful. Thanks a lot sir.
@Kona5.0 3 жыл бұрын
Great video!! The key programming was more simple than the actual key fob lock/unlock. Especially even compared to the long wait time GM requires when programming new keys.
@aussiefirestorm 7 жыл бұрын
Works on RX330 also. Thanks so much I had my scan tool for the immobilizer function , but had to use this method for the remote to lock and unlock doors.
@speedkar99 7 жыл бұрын
+aussiefirestorm Thanks, glad it worked out for you, and yes this is similar for all Lexus models before the smart key.
@rotcataergeht 7 жыл бұрын
aussiefirestorm HOW can i reprogram a used rx330 key fob bought from ebay on my rx330? i lost my old key fob while fishing.
@rotcataergeht 7 жыл бұрын
Not working on my 2006 rx330 using techstream version 10.29.30. bought a used rx330 key fob w oem chip from ebay.
@Kevin-yr7mr 7 жыл бұрын
Thank you so much for this video! My key and chip were separated without a housing so my car wouldn't start even though it's a master key. Turns out the chip needs to be next to the transponder!
@speedkar99 7 жыл бұрын
+Kevin Okinedo It sure does. Glad it helped.
@mradhakrishnan3549 2 жыл бұрын
my car not start,key put in the key cilinder security light blinks.what is the solution
@wholeNwon 8 жыл бұрын
Some years ago, I wanted an extra transponder key. I provided the key code to an Ebay merchant. He shipped a precut key. I simply programmed it in the car with the master key and everything worked great. The price was good and, more important, I didn't even have to set foot in the Lexus stealership...er...dealership. They could also cut the key based on the VIN #.
@speedkar99 8 жыл бұрын
+wholeNwon I bet you have a previous gen car and programmed it the normal way by pressing the gas pedal and opening the door etc, similar to this: kzfaq.info/get/bejne/Z8d7lZxnu56lZGg.html
@wholeNwon 8 жыл бұрын
+speedkar99 Right, it's one of the last series. Great car.
@wcolby 5 жыл бұрын
You finally got your thumbs up from me. note: you can’t use the valet key to program. I had to use my back up credit card key to program. great video! thank you
@speedkar99 5 жыл бұрын
You are welcome. Of course the valet wouldn't work, otherwise the valet driver could be doing this to your car!
@MrsBetterthanblessed 5 жыл бұрын
So the valet key won't start the car until you can get the new one programmed?
@wcolby 5 жыл бұрын
MsBetterThanBlessed To clarify, the valet key will start the car. What it will not do is allow other keys to be programmed. The valet key cannot be the source of the permission for programming new keys.
@wcolby 3 жыл бұрын
@Henry Luka I have blocked both of your fake accounts.
@bennettlachlan973 3 жыл бұрын
you all probably dont give a shit but does someone know of a tool to get back into an instagram account?? I somehow forgot my login password. I would love any tips you can offer me.
@andalebgover1252 6 жыл бұрын
Excellent instructions. This is great software.
@speedkar99 6 жыл бұрын
+Andaleb Gover thank you
@googleuser1684 6 жыл бұрын
You are a God among men! Thank you!
@speedkar99 6 жыл бұрын
+Google User glad it helped
@thefleaflop 8 жыл бұрын
Thank you for your response. Your are correct,... it should work and probably will work once I get the correct key. My eBay dealer sent the wrong key (electronics). They say the definition of insanity is doing something over and over expecting a different result. I was definitely INSANE yesterday, watching your video and back out to the car..... WoW!!!!! I know now, if I would have done it the way you did it,.... swapping elec. with the shell of the master, I would not have wasted a key cutting....,....
@speedkar99 8 жыл бұрын
+fleaflop ... Yes, but now you can still reuse that key shell with the new eBay electronic guts, right?
@Pimp-lc7vk 8 жыл бұрын
+speedkar99 I only have valet smart key on 2004 Lexus ls 430, can I use techstream to erase code to all existing keys to program my new key as a master key. I have techstream but I'm scared I might erase my only key recognized by my car. Would really appreciate any help!
@BarryRnGuitar 4 жыл бұрын
Clear, precise and on point. Great work! Thank you!!
@speedkar99 4 жыл бұрын
You are welcome
@Joe333x 4 жыл бұрын
You can also program the remote buttons with TechStream much easier using the Main Body ECU Utility.
@speedkar99 4 жыл бұрын
Yes
@michaelchu802 Жыл бұрын
How ? Any instructions? Thanks ! Nvm, figured it out. Much easier ! Thx
@Joe333x Жыл бұрын
@@michaelchu802 i dont remember its been so long but TechStream guides you through what to do
@michaelchu802 Жыл бұрын
@Joe333x yes thanks ! Definitely is pretty straightforward.
@torque6389 9 ай бұрын
Thank you for sharing this!
@MYKEYSAUTOMOTIVE 5 жыл бұрын
Amazing freaking video !! Love how you can talk!!!
@speedkar99 5 жыл бұрын
Thanks! What more would you like to see
@Omar-on804 4 жыл бұрын
thanks a lot this video helped me program my key for 2002 es300.
@speedkar99 4 жыл бұрын
Glad it helped!
@SK4869 8 жыл бұрын
it's so easy once you know how. thanks my buddy. your the best, thumbs up #6 :)
@speedkar99 8 жыл бұрын
+SK4869 Thanks
@Alex-cc6ge 8 жыл бұрын
+speedkar99 thanks
@Alex-cc6ge 8 жыл бұрын
+SK4869 Thanks
@Alex-cc6ge 8 жыл бұрын
+SK4869 Thanks
@bamnjphoto 5 жыл бұрын
Thanks for this video saved me a fee from Lexus to program my remote
@speedkar99 5 жыл бұрын
Glad it helped
@davidcordyceps6308 6 жыл бұрын
You are a fucking hero! Thanks for posting this, you definitely saved me hundreds of dollars.
@speedkar99 6 жыл бұрын
I'm glad it helped
@sheikhjewel4222 4 жыл бұрын
Nice video Sir! I have 3 Teachstream softwer vr14/vr12.
@speedkar99 4 жыл бұрын
Welcome
@JoshDunlop1 3 жыл бұрын
Thank you for making such a complete and succinct video! This is amazing and helps out a lot!
@Alex-cc6ge 8 жыл бұрын
great video thanks to the author of this movie
@wc2006 3 жыл бұрын
Its not a movie its a video
@beckyiverson6421 4 жыл бұрын
I watched the second half of your video (great presentation by the way)can not program the remote to lock/unlock any tips. Aftermarket keys start the car but for some reason, I am unable to get the fob to program. I have a 2006 Lexus RX400h
@danielcrecco5210 3 жыл бұрын
Have you found a solution to this? I have the same problem. Maybe because it is an aftermarket key?
@amyroseblazethecat8807 7 жыл бұрын
that easy key programming this Lexus and Toyota
@speedkar99 7 жыл бұрын
+Raions World The toy foxy - minecraft Wild SFM fnaf yes its easy
@robertmorris1467 6 жыл бұрын
H
@mahmoudhantouli5434 7 жыл бұрын
thank you for your help again I will try today
@JamesBrice85 7 жыл бұрын
This video was great for me
@Limeayy 6 жыл бұрын
I have questions, could i just download a newer version of techstream and just download the drivers for the mini VCI and that'll all work out?
@wangofree 2 жыл бұрын
Excellent video!!
@speedkar99 2 жыл бұрын
Thanks
@mahmoudhantouli5434 7 жыл бұрын
hi I need help how you can reprogram the key for 99 Toyota camry after changing the ECM
@speedkar99 7 жыл бұрын
+Mahmoud Hantouli See my immobilizer hacking video.
@katsuramoneh 5 ай бұрын
so you’d still need a working key to connect techstream to ecu. you can’t originate w/o a working or master key?
@888zzz 2 жыл бұрын
Is there a chance that if you don't follow the programming procedure correctly that you can make a mistake which will prevent the computer from being able to read the original key and consequently the car cannot be started with the original key? I read this is a possibility at least with some Toyotas. Are there any risks at all with trying to program keys with Techstream?
@ConciergeAutosSanAntonio 8 жыл бұрын
Hi SpeedKar - great series - thank you. Question - I have a 2008 RX350. have the original master key. Ordered 2 "new" keys from Ebay pre-laser cut. Using a tool - I have the keys matched to the immobilizer - keys start the RX350 just fine. But following both the directions I received with the keys and about 10 other versions - including yours - I cannot get the car into programming mode so that the key is programmed to open the locks remotely etc. Any tips?? thank you!!
@speedkar99 8 жыл бұрын
+Concierge Autos if your door lock actuators or door open switch are worn it might give trouble. I believe there might be an option in techstream to setup the remote part instead of going thru the "door dance" procedure.
@kl18704 5 жыл бұрын
I have the same issue with a Lexus GX470. Could you let me know if you managed to resolve the issue? I programmed the key chip, but can't program the remote buttons on the key.
@static_ls4004 2 жыл бұрын
@MrChad97Z Do it with just the driver’s lock at the handle. No instructions called for that but it brought my LS400 into programming mode, but I ran into the problem where my new chip would not program.
@static_ls4004 2 жыл бұрын
@MrChad97Z Yes, this is for getting the car into “programming mode” to get it to learn the remote. There is a switch, which locks and unlocks all the doors, instead of cycling that, do it at that little indicator on the driver’s door next to the interior handle, cycle it five times.
@static_ls4004 2 жыл бұрын
@MrChad97Z When you press unlock only once on the key/remote, does it unlock only the driver’s door, and then the rest when you press it again? There is something programmed to recognize just that manual lever locking and unlocking, which made it work for me.
@shameermalik5540 7 ай бұрын
I have the same key shape for my ls 430. I don't like it. Can i buy an aftermarket remote that looks different and then program it the same way?
@franciscoduarte8249 8 жыл бұрын
Gracias pude hacerlo con mi Lexus RX330 2005! Thanks my friend....
@speedkar99 8 жыл бұрын
+Francisco Duarte Thanks, glad it helped.
@nebilbaqhum2162 7 жыл бұрын
i tried programming the lock/unlock using the same method on a 06 lexus rx400h and after completing the last key on/off.. nothing happens. key is still not programmed. its an aftermarket key.. is it possible the car has reached max number of keys? i tried the 3 key on off to see how many keys programmed using the new key and nothing happens.. thoughts?
@michaelphan3521 6 жыл бұрын
Nebil Baqhum I have the same car and same problem. I've been doing the chicken dance for 1 hour now.
@steverandell8526 7 жыл бұрын
what is the year and model of vehicle used in the video? My 06 RX400h is having difficulty with getting key programmed with techstream...
@speedkar99 7 жыл бұрын
+steve randell 05 es330. Should be the same as yours.
@xjssts7127 10 ай бұрын
Excellent video.
@speedkar99 10 ай бұрын
Thank you very much!
@EdHotin 6 жыл бұрын
Where did you purchase the software? I recently purchased the Toyota Techstream Software Kit with Mini VCI Cable but when I click on the Immobilizer Tab, the Utility Tab is missing so I can't register my new key. It's like the software is missing some functions.
@speedkar99 6 жыл бұрын
+Ed H perhaps you don't have an immobilizer?
@EdHotin 6 жыл бұрын
No, I know that it has one. I tried it again last night using a different PC and all the tabs were present, so I guess the software wasn't communicating with the ECU before but now it is. Everything is working fine now. Nice video BTW, Thanks.
@EdHotin 6 жыл бұрын
After doing some more investigating I found that the Techstream Version 12.20.024 doesn't have all the functionality using Windows 7 so I installed Version 12.10.019 and everything works perfect.
@EdHotin 6 жыл бұрын
Another thing I have noticed is that when I plug in the cable and connect to vehicle the wizard doesn't automatically detect my vehicle, I have to enter all of my vehicles info including the VIN. Other than this everything is working perfect.
@jamescc2010 5 жыл бұрын
Tried programmed via Techstream a new used unlock OEM smart key for 2013 Prius, but at the final step after placing a new key next to the power button and beeped, it never registered at the final step after putting it on passenger seat. I suspected a bad used key or low battery voltage? Any advise? I always worked most of the time for other customers(unless the key as bad with it didn't beep at all). It was interested b/c it actually gave me a beep, but not a second beep after placing it on a passenger seat.
@FD-is1ug 3 жыл бұрын
Do I need to purchase an activation key for the tech stream to use it?
@ItsReloj 5 жыл бұрын
This worked. Thanks
@speedkar99 5 жыл бұрын
Glad it helped
@donkaye1297 5 жыл бұрын
Very good video. Thank you for sharing your knowledge and know how. As you said, "Knowledge is power, and by sharing this knowledge we can all learn . . ." More power to you for the good work you do. On another note: Do you have a Video on how to reset the the Anti Theft in a 2004 Lexus RX 330 after the car battery is replaced. The battery died when the car was initially locked, and therefore replaced when the system remembered that it was still locked. That triggered the Anti Theft System. We have since then replaced the battery and are able to disarm and arm (unlock and lock doors) using the Remote Control and the Master Key but can not start the car. We can turn on the ignition but can not start (crank or turn over) the engine. Also the Radio, AC & Fan, and Windows are inoperable. We can only lock, unlock, and turn on the ignition. Do you or anyone know the solution/procedure on how to reset the system. Thank you in advance for your help.
@speedkar99 5 жыл бұрын
You are welcome. I'm not sure how to reset the alarm system Unless if you need to reprogram all the keys...you might need techstream with a locksmith code...
@donkaye1297 5 жыл бұрын
@@speedkar99 Thank you for your response. I still have not found a solution. If you come up with anything, please let me know. Thanks again.
@panick.attack 6 жыл бұрын
Worked wonderfully on my 2008 Toyota Rav4! Thanks a ton!
@speedkar99 6 жыл бұрын
+kongology good to know. Did you use techstream to program keys?
@panick.attack 6 жыл бұрын
speedkar99 yes I did.
@othmankimweri8415 Жыл бұрын
I am confused about something. Why do I need that equipment. On some older toyotas you can program the key by just putting the good known key in the ignition and then replace it with the key to be programmed
@kewlnorcaldude 7 жыл бұрын
On my older 97' Lexus GS300 I only have a factory spare, and no original master keyfob...I've never had any problems with immobilizer so if I buy a new blank Key fob from Ebay...can I just program only the door lock features, and just have the key cut duplicate instead?? I already have another aftermarket Viper alarm installed. But would just like a nice key fob all in one.
@speedkar99 7 жыл бұрын
+kewlnorcaldude you can't program with valet key
@MYKEYSAUTOMOTIVE 5 жыл бұрын
Should do the on board process way easier and faster
@FD-is1ug 3 жыл бұрын
I have the techstream software and cable...I purchased it about a year ago but never used it...I'm having trouble with the registration key...any suggestions?
@speedkar99 3 жыл бұрын
Isn't it just 1111 or 0000?
@ItsBloxable 8 жыл бұрын
How would you go about programming a remote for a 2009 Corolla if there is only a start/stop ignition button?
@speedkar99 8 жыл бұрын
+ItsBloxable You could probably use techstream for that. Didn't know the 09 Corolla comes with stop/start.
@camilo11315 7 жыл бұрын
hello great video, I have a es300 2002 lexus. Only with a valet key. ( it can't open the trunk or glove compartment) I bought an aftermarket new key that I cut that seem to be able to open trunk,doors and glove compartment but is not program yet. (it cranks but it doesn't turn on the car) what should I do? the new key looks a bit longer and comes with the three bottoms. I really want to program this key that seems to be a master key. thanks
@efrizalbuyungmasterkeytoyo7747 7 жыл бұрын
good information
@speedkar99 7 жыл бұрын
Thanks
@efrizalbuyungmasterkeytoyo7747 7 жыл бұрын
Any vidio for LC 101 2002 years production . ? I you have . please sent link it . thanks ..
@rotcataergeht 7 жыл бұрын
Do you have video for lexus rx330 key fob programin with immoblilizer chip? i bought used rx330 key fob from ebay lost mine while fishin.
@josephereomala2580 3 жыл бұрын
can i use vci to program key for lexus rx300 and highlander 2002 model
@speedkar99 3 жыл бұрын
Yeah
@lonetraveler5660 3 ай бұрын
Is techstream able to program 17 rav4 remote with start button? Thank you
@mannymatias1194 7 жыл бұрын
Will tech stream work if I only have a key with a blank fob not programmed I lost my oem key nothing to program no one from
@speedkar99 7 жыл бұрын
+Manny Matias Yes but you need a locksmith code that the dealer has...
@Mambre79 6 жыл бұрын
How can I get the code apart turning to dealer? Software or tool?
@quanwang7832 5 жыл бұрын
hi i have bought a mini vci cable and it comes with TIS 13.00.200 software. on the software i dont see "utility" option to program my 2007 camry key. please help me! thank you!
@speedkar99 5 жыл бұрын
Try another cable or software? Maybe an older version, or run it on XP
@rayane454 8 жыл бұрын
Hi, Could you please show me how to program a new smart card for LX570 and can I program a used one using tis tecstream. Thanks
@toanphan6774 5 жыл бұрын
Good video. Can you recommend the link to exact key to be purchased on ebay which will definitely work? I see lots of keys there and dont know which one is good. Thank you.
@IbzJaay19 5 жыл бұрын
If i buy a Toyota Yaris 2009 car key transponder 4D67 chip, can i register it using this software so it starts the car?
@speedkar99 5 жыл бұрын
Yea
@hassansmw5634 2 ай бұрын
Can techstream program a new ecu for a 2004 ls430 with a key fob?
@maatouguimaatougui7698 2 жыл бұрын
I want to know where is the emo box in the Toyota Hilux 2021
@ae86ptan7 7 жыл бұрын
Will this process work on an IS300 with only the programmed valet key and one non programmed eBay master key?
@speedkar99 7 жыл бұрын
+Patrick Tan Nope you need one master key to add new keys. See my immobilizer hacking video
@Techman-pt5zs 8 жыл бұрын
I have seen many clone Techstream on youtube. I don't buy clone scan tools because if it breaks who am I going to call in china for tech support or warranty. I see they are pretty cheap but it won't do any programming. I see it works well for you.
@speedkar99 8 жыл бұрын
The techstream cables work fine for Toyota immobilizer programming. Honda HDS MVCI cables won't work for immobilizer programming though. This cable has paid off for itself, not to mention I can use the techstream software on any OBDII car (there's a global OBDII mode, I tried it last night on my Honda), so I can access all the engine sensors, graph them and record live data.
@MrPlannery 2 жыл бұрын
How can I tell if I have a master key? My Lexus came with two keys, pretty sure one was aftermarket.
@speedkar99 2 жыл бұрын
When you put the key in if the security light takes an extra blink to turn off then that's the valet
@kabtamugetu3915 6 жыл бұрын
usefull information thank you
@speedkar99 6 жыл бұрын
+Kabtamu Getu thanks!
@WilmerJael 7 жыл бұрын
Awesome! I have a question now, I only have the Valet key, no master key, can I reset the ECU using Techstream and programming the keys I bought off ebay?
@speedkar99 7 жыл бұрын
+Wilmer Jael Yes, but you need to enter a code that only dealers have access to a database for to Virginize the chip.
@johnkim1656 4 жыл бұрын
@@speedkar99 So if I only have (1) Valet Key, then I must go to the dealer to get it programmed?
@racerxone2144 6 жыл бұрын
I only have a valet key. Do you have a video for clearing all keys and reprogramming new master and valet with techstream? thanks
@speedkar99 6 жыл бұрын
+Racerx One see my immobilzer hacking video
@enggwahaj Жыл бұрын
In case of all the keys are lost, can a techstream program a key ? erasing all the keys from an immobilizer and program new key?
@speedkar99 Жыл бұрын
Yes but you might need a dealer code
@enggwahaj Жыл бұрын
@@speedkar99 are you in Australia or USA?
@liyangtime 6 жыл бұрын
Good video, I only have one slave key for my 2004 Toyota Solara, and am going to get a master new key. as well remove slave key chip. Do you think slave key's chip will help with finishing new master key register?
@speedkar99 6 жыл бұрын
Yes
@muhammadkhresat7004 Жыл бұрын
Can you get a Car Key cut with the Vin number
@morg4620 8 жыл бұрын
Where did you get tech stream software and how much.
@speedkar99 8 жыл бұрын
+morg4620 Roughly $25 for the cable and it comes with the software or you can download it online. More info in this video: kzfaq.info/get/bejne/gaqgn8dy25bZgXk.html
@alram5664 8 жыл бұрын
Are you home Techstream? Do you know if a used Toyota "G" transponder chip can be reprogrammed?
@speedkar99 8 жыл бұрын
You mean a wireless key? I've heard it can be reused but there's a huge workaround.
@forexsanjose6090 2 жыл бұрын
Does these key remotes work with 2006 lexus,such as IS GS etc?
@speedkar99 2 жыл бұрын
2006+ Lexus use the proximity fob. Much different than this
@sukhpreetsingh7721 6 жыл бұрын
I am having trouble trying to program the chip, i was able to register the buttons to unlock and lock however teachstream shows asterik * by immobilizer and couple others. When i first start the program and click immobilizer i get this "Selected system is not responding or not available. Please check the repair manual for applicable systems." Do you know what is wrong? i tried teachstream on windows xp 32bit and 7 32bit. version 12 and 8 of techstream. Is it the cable? its a master key not valet key and it is G chip
@speedkar99 6 жыл бұрын
I think the only problem I had with techstream not connecting to certain features was on my brother's GS300. The same cable and software worked on a dozen other cars. So I'm sure it's just your car or it's not compatible with the cable.
@kmschn3321 4 жыл бұрын
thanks your the best
@dhonamla 2 жыл бұрын
can you do that with toyota sienna 2013 remote?
@speedkar99 2 жыл бұрын
Yeah
@simonmugume806 2 жыл бұрын
why the light keep on brinking after programing a key
@davel757 8 жыл бұрын
speedkar99 thanks for the great video. I have 05 RX330, with 1 master key which includes the remote. I am trying to get a second working key. I bought a used remote ("chip") from ebay. Do you know if the used ebay remote can be programmed like a brand new (never been programmed) remote? I'm confused b/c with the new smart keys (2010 +) used remotes cannot be programmed like "virgin" remotes. Thanks!
@speedkar99 8 жыл бұрын
+D L Yes it can be reprogrammed on the RX330. Used Smart keys can be programmed too but theres a work around to get them virginized again.
@rotcataergeht 7 жыл бұрын
D L Did you get the used rx330 key chip to work? failed on my 2006 rx330.
@jamescc2010 5 жыл бұрын
@@speedkar99 Can you make a video on this work around ?
@mahmoudhantouli5434 7 жыл бұрын
good morning thank you for your help but my problem is ECM it's not good any more and I do have mastertech Toyota scanner and I can't do it
@speedkar99 7 жыл бұрын
+Mahmoud Hantouli So you need to replace the ecu and then goto erase keys and enter the technician code to Virginize the chip and program new keys.
@mahmoudhantouli5434 7 жыл бұрын
This car the chip in side the key
@mahmoudhantouli5434 7 жыл бұрын
My friend what can software u used for reprogramming ?
@speedkar99 7 жыл бұрын
+Mahmoud Hantouli Ponyprog
@mahmoudhantouli5434 7 жыл бұрын
Good morning can you please send me pictures of it because I found to many of these tool and I don't know right tool I'm looking for
@user-vd6gd9nh4g 6 жыл бұрын
Hi do you have to Pay online to do programming key on this Software Or make an account, Im try to buy one from eBay but the Review said you have to purchase the account it’s almost like $500 for the whole year I just need to do programming key and remote for my car 2011 camry or it’s free? Please advise thank you
@speedkar99 6 жыл бұрын
+Smsm A you can buy the knock offs on amazon $20
@user-vd6gd9nh4g 6 жыл бұрын
I’m planning to buy This one from eBay it’s exact same yours but the only things I want to make sure to I don’t have to pay a lot of money to make an account and program the key rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F302268796698 Please advice thank you
@thefleaflop 8 жыл бұрын
yes but the reason I bought the TTS software in the first place was to find out what was going on with my SRS dash light. Its not throwing a code in the software. Does your cable stay green thoughout the scanning process>? I have two cables and both stay red/orange from the time I load the software. Have v8.10 on a laptop and v10 on a desktop and both machines create a orange light with both cables. Can you do a cable check on your system and relay findings? thanks,
@speedkar99 8 жыл бұрын
+fleaflop ... The color of the LED on my cable does not change when it is transferring data regardless if it's plugged into the obd port. What's wrong with the SRS light?
@kamalmani695 3 жыл бұрын
I tried doing this on my 07 LX470 but it always gets stuck at the last step (75sec) Saying "Communication error occured between the key and the ECU" Any thoughts?
@speedkar99 3 жыл бұрын
Hmm sometimes it bugs up, and doesn't work on all vehicles
@kamalmani695 3 жыл бұрын
I figured out the issue. 06-07 models changed the transponder model#. Ebay and Amazon sellers typically sell the ones compatible with 98 to 02 but they claim that it will work upto 07 models.
@Aay-jay989 6 жыл бұрын
For the door locking program... i got mistaken the steps will it affect the key?how many times can i try the procedure?
@speedkar99 6 жыл бұрын
+abed aljabbar it shouldn't affect it. Just open the door and close it and start again
@wilmergonzalez2906 6 жыл бұрын
Can I program a used transponder from another car to be used with my new key (which has no transponder, it's only the blade and the shell)?
@speedkar99 6 жыл бұрын
+Wilmer Gonzalez yes
@jamescc2010 5 жыл бұрын
I programmed a smart key on 2010 Lexus RX450 and everything was good except the new key cannot open the truck like the original is. Sometimes this happened on other cars as well but most of the time it worked. Any thoughts?
@speedkar99 5 жыл бұрын
The remote is programmed separately from the smart key to start the car
@jamescc2010 5 жыл бұрын
@@speedkar99 I will check it out. From the past with Toyota smart key programming, one key programming step was enough to also program all remote functions. It could have been due to the refurblished remote my client has as well.
@dridhoc7978 7 жыл бұрын
Hi is the Cable you used is Mini vci ? Does it do every thing considring scaning for errors and reprogrammin keys?
@speedkar99 7 жыл бұрын
+Drid Hoc yes it does
@basil4everx2007 6 жыл бұрын
My friend has a 2003 lexus es 300 and it has a c1336 code and VSC lights are seen on the dashboard ,what could be the problem and how should I fix it ?? Thanx
@speedkar99 6 жыл бұрын
+Basil4everx You might need techstream software for that, or there might be a diagnostic mode. This video shows key programming.
@osamahamdy1401 9 ай бұрын
Can used this to program an already programmed key. Means if I want to use my key for another car?
@speedkar99 9 ай бұрын
Yes for older Toyota
@osamahamdy1401 9 ай бұрын
@@speedkar99 not for 2015 corolla?!
@osamahamdy1401 9 ай бұрын
@@speedkar99 I mean friend if I want to program my car’s key for my friend car and give it to him. Is this applicable? Corolla 2015
@nikocruz3638 5 жыл бұрын
I followed all the steps to get the unlock and lock button to work with the car, i held the buttons together and released and hit the lock button but nothing happens. I tried all of the steps over about 10 times. And still nothing. Even went outside of the car. Please help me program this feature! Thanks. Any suggestions?
@speedkar99 5 жыл бұрын
Check the battery in the remote and the door lock actuators
@yuj18907 8 жыл бұрын
question, I got "Key Registration has failed. The communication error occured between the key and the ECU", any idea on this error? The device I ordered from amazon mini-vci j2534 , comes with the software. It detects my Lexus rx330, but failed for registering additional key.
@speedkar99 8 жыл бұрын
+Jian Yu Are you sure the key your using is functional and compatible with your vehicle? Perhaps try programming another key out of a Lexus or Toyota with the same chip (swap the chip part into the key) and see if it recognizes it.
@tomknud 4 жыл бұрын
My version is 13 and it shows NO functions. I can't even see the code for the tire sensor light. But, it claims to hook up. It just asks for vehicle configuration code. Any ideas about that?
@speedkar99 4 жыл бұрын
Never heard of that. What vehicle?
@tomknud 4 жыл бұрын
2007 Camry Hybrid, evidently the same for 2007-2010 Camry's.
@peteradegbola4508 8 жыл бұрын
pls in programming the remote,can d existing remote for my former highlander be added to a new highlander.
@florentinarin7728 5 жыл бұрын
Hi. Could you please put a video how to program Toyota Camry 2009. Thank you
@speedkar99 5 жыл бұрын
Same method
@florentinarin7728 5 жыл бұрын
@@speedkar99 thank you. Probably the keys are not good , bought from e bay
@mathieudore7444 6 жыл бұрын
Worked on a 2008 rx400h. Everything works except the trunk button. Is there a way to program that button? It works on the old remote but not on the new programmed ones. I programmed the remote with techstream
@iceman9292 3 жыл бұрын
Same with mine... but for some reason i waited a month or so and now the trunk button works!!
@NewsBroadcasting 3 жыл бұрын
Question - i replaced the headunit in a Toyota landcruiser 2000 US 100 series with an android screen , the security light is gone as the android screen connects to HVAC via CANBUS connectors. Can this still work tech stream software?
@JohnCreasy85 6 жыл бұрын
Hi! I got Lexus LS430 02' president with only 1 key( 2 buttons lock/unlock) and I bought other used key from the same model car (3 buttons lock/unlock/trunk) When i turn on smart key option under the steering wheel the green LED works fine but i need to put in key to ignition to start vehicle . When i put used key its show communicate "key is different" My question is can i programm/add the other used keyto this car? Im using TIS Techstream. Can You please help?.
@speedkar99 6 жыл бұрын
+John Creasy check the battery in the working key There is a work around to programming used smart keys online somewhere, its not as straight forward as programming a new one with techstream.
@JohnCreasy85 6 жыл бұрын
speedkar99 bettery is brand new. About work which os somwhere do You fot any idea where is IT? Im searching IT from 2 days and everywhere od the same with close/Open door etc.,etc.,
@mirzo9154 5 жыл бұрын
Would you be kind enough to tell what kind of cables been there used by you when work with laptop?
@speedkar99 5 жыл бұрын
If you go on eBay or Amazon and search Toyota techstream usb to OBD2 cable
@JJ-rd2ef 6 жыл бұрын
Is it possible to reprogram a key if all the keys are lost for a 2001 Lexus gs300?
@speedkar99 6 жыл бұрын
Yes see my immobilzer hacking video
@nanabebo1 7 жыл бұрын
My friend has a toyota tacoma 2015 base trim that didnt came with wireless remote from dealer. we purchased 2 wireless remote and tried one of your video's instructions of going into program mode opening and closing the door but it didnt worked. After doing researches I saw that I needed to go to a locksmith to enable the wireless remote function in the toyota. can this be done over techstream or do I really need a locksmith?
@speedkar99 7 жыл бұрын
+nanabebo1 Use techstream to enable the wireless function. No need for dealer.
@elijahperez159 6 жыл бұрын
If u only have an engine swap with the immobilizer and everything needed except keys, can you program a key or chip to the ecu to make it run? I need to have this done if there is a way. Like put my ecu in a car and use its organs to program the chip to recognize each other
@speedkar99 6 жыл бұрын
See my immobilzer hacking video
@ellc9 7 жыл бұрын
Will this work with a 2013 camry??... I only have the copy key that doesnt have bottons on it.
@speedkar99 7 жыл бұрын
+ellc9 If it's a valet key (you'll know if the security light stays lit for 2 seconds after inserting) then you can't program new keys.
@ellc9 7 жыл бұрын
speedkar99 right when insert the key the light stops flashing
@vip001able 7 жыл бұрын
hi man can you give me the link to blase you buy the key From
@speedkar99 7 жыл бұрын
+Xya3 ionyX ebay
Friendeez
Рет қаралды 19 МЛН
TambourineMan
Рет қаралды 29 М.
Cristian A
Рет қаралды 29 М.
AWordFrom Mr.Jones
Рет қаралды 42 М.
@Iamcarhacker - Car diagnostics & Coding
Рет қаралды 51 М.
Blue Moonshine
Рет қаралды 10 М.