Thank You Thank you Thank you for taking the time to actually put the link in the description for these parts. I owe ya a beer!

Wanted to say thank you! Your video, especially the throttle linkage info was very helpful. FYI - the throttle spring can be a real pain as you noted. I took the spring and compressed it on my bench and used two bread ties to hold it compressed. Then I slid it over the throttle cable and installing the cable into the needle valve was a snap. After the cable was attached to the needle valve I just cut off the ties with a sniper. Presto. Thanks again!

Thanks for taking the time to make this video - very helpful!

I wasn't certain on the direction of the gasket and the video confirmed for me thanks buddy

Hey Bud. You are very lucky to have hands that can reach in to R and R that carburator. That quick project looks like an excercise in frustration for me. Good job

Thank you for the information. Super helpful!

Right on thank you helped me out 👍

Thanks just what i was looking for

All I have to say is WOW. Thank you for taking the to create this video and include the links for the Carb on Amazon. I'm new to ATV repair and watching this video now gives me the confidence to try this repair/replacement. Thanks again!

Dude, you’re flipping awesome. Great job and thank you. Buddy of mine just gave me his (4 my dtr) and this video is what I was looking for. Grassy ass, me amiger!

Very helpful

Thankyou, helped me out alot, great work

Thanks I really need some one to know what you doing great job

Great tutorial. I came for the part where you use the new needle part

Good job

This video is great. You allowed me to change the carb! However, i have a problem. It now starts and hits wide open throttle and runs full RPM - no idle adjustments seem to stop this. Any suggestions? Help! Merry Christmas Note that i did use the OEM/existing needle and spring and not what came in the kit (an earlier poster said this may be a bad idea).

thanks!

Interested in how you fabricated that seat on the back!

Good job man, I buy one used and I don’t know if used only gasoline or mix ?

Hey this video is awesome!! I replaced the carburetor that was leaking with a new one and now no leaks!! It is idles great in neutral but it will not idle in drive for more than a minute. Tbh this has been a constant issue do you have any suggestions on why this might be happening?

do you have a video on how you built that backseat

What do you do with the hose that plugs into the air filter? My new one doesnt have an attachment

Didn’t know hoe to disconnect the throttle linkage , thanks 🙏

Reason I ask is cuz I screwed up where the lights attached I broke the plastic just wondering how to rig it so it don't move

Got mine running good now thanks. I’m just wondering it seems like it’s going really slow but the rpms go really high, do you think there is a problem with the transmission?

Happy to see sum1 make a video on the exact bike my son has..im having a problem with it revving high & taking off soon as it starts. It have a new carb on it. It was running fine..next thing it started dying on throttle..messed with the fuel mixture screw & now its doing the revving high crap..i turned the mixture screw in & nothing turn out & nothing..throttle seems to be fine also..its not caught or ran funny. Idk whats going on lol...got any idea??

you can use a small zip tie to compress the spring and hold it till the throttle cable can be reattached, then just cut the tie and remove it

Pretty cool video but I have a question why would you put a smaller diameter carburetor on your motor in the video it looks clearly your stock carburetor looks bigger in diameter than the newer one I was just curious if there is some kind of something behind it thanks

Did the replacement carb cure your issues permanently? We bought one of these ATV's for my grandson last year and the carb has been a source of constant frustration...sometimes it will suddently die while riding and if I bounce the front end up and down really hard a few times, it fires right up. Other times, he will be riding and it will be pouring gas from the hose coming off the carb.

I purchased the same kit that you did based on your suggestion. However I couldn't tell the direction that the new fuel filter needs to be in. I could not see any directional lines on the new fuel filter. What symptoms would I have if the fuel filter was put in backwards?

Hey man, I just picked one of these for my kids. The fuel lines froM the carb to the tank are not there. Was wondering if you had a diagram where exactly the fuel lines go? Thanks man

Question: if you use the new air filter, since it doesn't have a hole for the breather tube to connect would that be bad in a way where the atv wouldn't run or so?

Did you use stabil fluid for your gas so it doesn’t clog your carburetor.

hey i didnt see you put any kind of gasket underneath the carburator do a gasket go underneath it or not just asking i have a 110cc atv for my son and i order one for hi atv but i fogot to order a gasket please let me no if i need one or not

Mine cranks but does not turn over. Any suggestions?

You have a video of a headlight replacement headlight or bulb replacement

I have a coolster and it wouldn’t start yesterday...there is on fuel line tube that isn’t connected and I can’t figure out where it goes. The tubing going into the carburetor is fine. This is another tube leading away from the carburetor and has the metal coil around the hose. It’s totally disconnected and leads toward the bottom of the atv. I see no where for it to go! Any help?

? Is the carburetor on my 110cc four wheeler and I put it back on and it's not giving the gas the proper gas to it is that means that there is an overflow in the tank

Ok I did all this, I’m having trouble with idle and air mixture screws, it bogs down when gas is mashed, it runs like crap

In case anyone thinks they wanna replace the carb and not replace the needle jet etc it’s not a good idea to use the stock needle jet & spring assembly “aka the thing you screw out of the top” 😂 there’s notches for adjustments on the aftermarket needle jet to aid in helping you lean out the carb or richen it up that are simply not present on the janky factory setup

Where can I purchase the kit for the mini at...please!!!

Mine won’t start after putting on new carb

My sons 110 starts but as soon as u throttle to ride off it goes off ...can u help please

where did you order the carburetor from

What do I do when the electric start doesn’t work? Please answer, anyone if you have this problem and you fixed it lmk how you did it

How would I make the atv faster

What kind of carb is that bro?

Why are the manifold bolts on my vitacci 125cc. 8 mm.

The bottom hose with the spring on it is that supposed and supposed to connect to anything

You called me a dummy😢