Using the Teflon tape is worse than not using it in the sense that it does not contribute to the seal but interferes with the tightening of the threads that do.

@@jimmonte9826 Possibly. Many people think the teflon tape is for sealing when in reality it is really considered a thread lubricant. I had a plumber friend correct me some years ago when I mentioned sealing threads with Teflon tape.

Glad this helped you!

Glad this helped!

yes brass and copper eventually corrode but pvc does not, but when it comes to sprinkler systems and where the valves are, or elbows pvc piping can break, due to cold and hot temps. the pvc piping usually should not break inside of your home unless there is a flaw in the the manufacturing of the pipe it didnt cure properly in an area, but have not really heard of pvc piping breaking that are in between studs of a house I am sure it is possible but highly unlikely over copper or brass piping corroding over time and springing a leak.

I'm glad this video helped you. Thanks for letting me know!

I was wonder the same thing because I’m having that problem now and all the videos to replace it use the washer

I'm glad this video helped you...thanks for watching and taking the time to comment!

Cool! Glad I could help...

Real talk, important to not consult the father in law sometimes

Just like checking for brake line repair leaks, you need to pressurize the system before you know for sure if your repair is good.

Thank you so much for this comment! I'm new to this, and this helped me. When resetting the tailpiece, I didn't have it far enough into the p-trap, and your advice allowed me to catch that now rather than later! I removed it, reset it properly, and tested successfully. Thanks again.

Glad you stopped your leak!

Was here to see how to cut the PVC extension pipe. You did mention hack saw but without video.

Stuff like that happens. Glad you were able to figure it out

Glad I could help

Me too, in fact, I thought I had to get a whole sink if I. Really honest! I'm psyched! I love you tube.

Glad I could help! Thanks for watching and letting me know...

Glad this helped!

I'm not sure I understand what that means. Don't. Put that tape on the threads? It's not connecting to the wall. U just threw me for aloop, I was ready to go now I don't know! Please explain?

I'm glad my video helped! thanks for letting me know!

I always use Teflon tape. Its a habit I picked up from watching my dad when I was a kid and has served me well over the years.

BTW, is that dishwasher a Maytag?

Nope - it's a Whirlpool.

Same company, my dishwasher discharge hose is identical!

Pipe is sold by it's diameter, not circumference. Just measure it with a ruler and you should be good

The product IS made in China. The headquarter is located in Connecticut.

I thought it said "made in USA" on it. If it's really made in China then that's obviously a false claim...

I don't have sewer gas lines to turn off. You should consult a pro

You might need plumbers Teflon tape on the threads. Or,bit could be leaking some other place and clinging to the pipe making it seem like it's leaking at the threads

@@SevenFortyOne I did use Teflon tape and wire brushed the threads but still leaking

Best thing to do is go to Lowe's or any similar home supply/hardware store and check to see if they have something that will work before you cut the pipe.

Mine seems to work fine ad it is, but a second clamp probably won't hurt if you want to add one

Sorry for the delayed response but thanks for the support!

Didn't look like one came with the kit so it may not have been installed. Flanged fittings are unique and different than most under-sink connections, which use tapers. Here's what was needed for your application. www.plumbingsupply.com/images/tdp-1andhalf-poly-tailpiece-washer.jpg That tapered washer you installed at the top (or did you go washer-less up there?) will leak. The bottom one is correct. Note: this is a "top hat" washer for flanges and goes INSIDE the tailpiece between the plastic tailpiece and the metal strainer so when you tighten the nut, the washer compresses and makes waterproof the connection between the tailpiece and the strainer. Hope that helps. -- EDIT: After watching again, the Teflon tape may be saving you but it's not best practice.

That's what I heard too.

You do not need to because it is a low to zero pressure flow. We do it all the time at wastewater (sewer) plants and alternate between metal and plastic so the joints don't rust fast.

No, that was an old wire brush with a wooden handle...kind of loos like sandpaper though doesn't it?

Ah, okay that makes sense.

As of 2022 you are correct, however, this piece was actually made in CT. Unfortunately, the company that made it was bought out and closed in 2019 4 years after this video was published...

@@SevenFortyOne One day, we won't be able to get common things anymore due to Chinese manufacturing problems, and having sold our entire country away. Oh, wait, that's now.