Knocking Ford Mustang 4.6L 2v Complete Engine Teardown | Avoidable Mistake or Random Failure?
Рет қаралды 6,684
Жыл бұрынToday were tearing down the modular 4.6 2v out of my mustang drift car to find out what failed. It made on a tune with only basic bolt-ons such as an intake and headers around 260hp. The car was fine until after a spark plug and coil pack cleaning due to the common issue of water getting down in the spark plug wells on these engines. once it was started after this it began to knock severely, you can watch more about it in my other video on it : • When Good Engines Go B...
Check out my Instagram: skid_valve...
Music:
Song : Shards [Intro Version]
Music provided and produced by LonePeakMusic
Video Link :
• Intro Music 5 Sec...
Song : New Day [Intro Version]
Music provided and produced by LonePeakMusic
Video Link :
@RandallSchrecengostJr 9 күн бұрын
100% dropped something down the spark plug hole. These engines are indestructible
@skid_valve 3 күн бұрын
Its the only thing i can think happened just weird it didn't mark up the cylinder more
@c4b0ombazzist90 10 ай бұрын
Looks like the piston over extended into the head, excess play in connecting rod bearing or wrist pin.
@gunnerv12 4 ай бұрын
how do i prevent this
@markboyce1001 Жыл бұрын
The 4.6 or 281 Ford motor is not a hotrod motor from the factory,with only 231 hp in average,it a good motor that holds up with very little maintaince, my has 241000 on it,it burns clean,and after looking inside the cylinders with my scope,the top of the pistons were clean,very little carbon,used no oil,and no leaks.
@skid_valve Жыл бұрын
hmm thats weird for not being a hotrod motor it seem to have came in a muscle car, not only that the block is almost identical to the 4v that came in the mach one and cobra, and shares the same architecture as the newer coyote. I beat the piss out of it Im not too upset it was a matter of time! glad to hear yours is still running well.
@tbmg4050 7 ай бұрын
That water pump is no joke!
@alexdowns5562 12 күн бұрын
I remember replacing mine. I’m like all the bolts are out this thing should just fall off. 4lb sledge didn’t do anything then I figured out it slides in and out 🤦♂️ really shocked nothing broke.
@c4b0ombazzist90 10 ай бұрын
Check out the stroker kits for the 4.6
@ryanclifton7033 3 ай бұрын
I have a older non pi engine that just recently has a spun bearing
@SergioGomez-to1jl 7 ай бұрын
If I remember correctly the typhoon intakes made less power than the oem P.i intake
@skid_valve Ай бұрын
thats a real possibility but i bought it mainly because the all aluminum design stops from having the plastic intake breaking issues
@kenzeitner4704 7 ай бұрын
That kinda damage is normally and usually from detonation
@skid_valve Ай бұрын
yeah detonation is defiantly a possibility
@florenbaron7111 2 ай бұрын
Is that the Triton engine found in some Econoline vans?
@skid_valve Ай бұрын
nope 4.6 2v that was put in crown vics and mustang gt's
@windsorwill2261 6 ай бұрын
My guess excessive rpm Piston kissed bottom of the head and kablooey
@WarriorOfEden3033 3 ай бұрын
Timing thrown off these are interfaces engines
@skid_valve Ай бұрын
its on stock limiter so idk what could have happened other then something falling in
I Do Cars
Рет қаралды 294 М.
Danny Johnson’s Garage
Рет қаралды 101 М.
Garena Free Fire Global
Рет қаралды 60 МЛН
I Do Cars
Рет қаралды 495 М.
Danny Johnson’s Garage
Рет қаралды 105 М.
POWERNATION
Рет қаралды 280 М.
Richard Holdener
Рет қаралды 87 М.
FordTechMakuloco
Рет қаралды 692 М.
I Do Cars
Рет қаралды 304 М.
jamoloniy
Рет қаралды 1,6 МЛН