Knurling - Solidworks Tutorial

No video

Knurling - Solidworks Tutorial

Рет қаралды 21,921

Күн бұрын

Solidworks Modeling Tutorial
Do you want to learn how to use Solidworks?
In this video you will see a Advanced Modeling example. Some Commands used in this video as follows:
Extrude
Revolve Surface
Pattern
Chamfer
Planes
Sketch
For more videos and quality contents, please subscribe. !

Пікірлер: 28

@aadityashah8884 27 күн бұрын

You the goat for this!!!

@DougCardo- Жыл бұрын

Thanks for the great video. I also modeled a knurl by using a helix and swept cut, but it took my computer about 7 minutes to rebuild which is way too long. This method using a patterned boss only took a few seconds to rebuild. Mush faster! Thanks for the tip.

@ZanderdeBeer-nz6ne 3 ай бұрын

Thank you for the help! It was very easy to follow along and play to my own project.

@3D-World 3 ай бұрын

Thanks for your comment!

@RonAdamsky 2 жыл бұрын

Thank you! Interesting method with extrude boss instead using helix and extrude cut. As always precise tutorial .

@3D-World 2 жыл бұрын

Thanks Dear 😉

@faffie5855 Жыл бұрын

A knurl is turned: extruded cut inwards e.g. 0,015inch per side ( 0,03" on the diameter), the same amount the pyramids are forged outwards and the bosses should be (0,015"). So the nominal surface stays at the same place. Therefor if you only use a cut or boss you have to compensate the surface (50% of the cut or boss using e.g. move face). The purchase raw part outer diameter becomes 0,03" bigger (at the tip of the pyramids): Not of great importance for a knob, it does in case of e.g. an insert.

@yogesh124 2 жыл бұрын

i always learnt many new things from your videos thanks for that I have only one concern Sounds in your videos are very low

@3D-World 2 жыл бұрын

Hi Dear, thanks for your nice comment. I have now a new microphone, I believe it will fix our problem

@Ntzyx-xu1uf 4 ай бұрын

You must have spent a lot of time before making this video to figure what even numbered dimensions for the diamonds will work ? For instance you just can't taper extrude at any angle . It reaches a point then it stops extruding completely. I find this method will give visually impressive results but thats only if you know exactly what the diamond dimensions are . Nothing but perfect works at all .

@wrecking_havoc586 6 ай бұрын

This was helpful. Thanks!

@3D-World 6 ай бұрын

Welcome 🙏🤗

@WhatTheFoxtroGarage7281 6 ай бұрын

Great video. Thank you

@3D-World 6 ай бұрын

Welcome, and thanks for your comment!

@saykatislam9518 2 жыл бұрын

Thanks a lot for the tutorial

@3D-World 2 жыл бұрын

Welcome 😉

@w.binder-freecadchannel 2 жыл бұрын

Very nice!👍🙂

@3D-World 2 жыл бұрын

😉

@user-rz9wg2fj3l 7 күн бұрын

what is the weight of the file? I'm rolling on a long length, solidworks starts thinking for a long time, and the file size turns out to be insanely large (about 40 MB)

@KamalSingh-ny9vw 2 жыл бұрын

Nice 👍

@3D-World 2 жыл бұрын

Thanks 😊

@HansRamzan 2 жыл бұрын

Thank you! Works but slows down solidworks so much. Any ideas on how to stop it from being so slow?? (I have a i9-9900k, rtx 2080ti, 16gb ram)

@3D-World 2 жыл бұрын

Hi Dear, Best thing you can do viewing and modeling in shaded mode without visible edges and deactivate realview graphics.

@faffie5855 Жыл бұрын

Try the function defeature, I think it's made for feature like this

@Ju-ww6sz 2 жыл бұрын

How did you learn cad?

@3D-World 2 жыл бұрын

I am self taught. 22 years ago I started when I was a 13 years boy there was no tutorial etc. The best way is learn program and go find a related work, then you will develop a lot.