That is some damn fine work! And thanks for the video, I just installed the exact set up with Uponor.
@robertlee4172 Жыл бұрын
After hummin' and hawing over pex and whether to crimp or clamp, I've decided just to go with 100% copper soldered pipes. The risk to flow restriction is just going to gnaw my brain out.
@cordobes16093 жыл бұрын
I AM INSTALLING SAME CONFIGURATION. NOW I WILL PUT THE DIRECTION VALVE ON TOP OF THE COLD HOT WATER INLET, CONNECTING FOR 3/4. ONLY A DOUBT I HAVE TO REMOVE THE INTERIOR PLUG I WILL ONLY USE 2 SHOWARE HEAT AND SIDE LINES. ELSE I INSTALLED THE CARTRIDGE AND I HAVE LOW PRICE IN COLD WATER SAVES WHY. Thank you very much I loved your video, heres a professional
@Xavier81712 жыл бұрын
I just installed this same set-up in a custom home, and I thought it was kind of odd turning the main valve on from left to right. I’m use to moen turning the valve on right to left. But, this was my first time messing with kohler.
@fabianoalmeida83182 жыл бұрын
Nice work showing the people how to do thks
@John-wx6nx2 жыл бұрын
See that you applied flux after soldering. Were they wiped off video or left on?
@brianmcglone29802 жыл бұрын
I installed one of these last week. Showers head and handheld on the transfer. This week customer ask for me to switch the tub spout to the diverter because his friend who is also a plumber said it should be the the transfer valve not the mixing valve I told him we shouldn’t do that but persisted, so o did it today. Went to test and I’m having issues. Shower head and spout run by themselves but the hand held won’t. The spout runs at the same time as the handheld can get it to run by itself. Do you think the spout is starving the water from the hand held? I’m going to call kohler on Monday but would love your input. Nice work
@carlmarinaccio503 Жыл бұрын
You would be better if you explained what your doing with the diverter. By pointing no one really knows what the heck is going on.
@JLitt-us4vs2 жыл бұрын
Great video👍 I’m doing the exact setup except in a vertical setup. Do you have to take out the stops? And why do they come with them? Just to have eco pressure?
@JLitt-us4vs2 жыл бұрын
Or did you just take them out to solder??
@joshuacaban21292 жыл бұрын
amazing video, I follow this and the water isnt being released to the shower
@tommyskusa99818 ай бұрын
Did you pull the integral plug for 2 way system?
@timquick9554 Жыл бұрын
Why not save a TON of offsets by stacking the diverter valve vertically above the shower valve?? (But nice job on the install, As a 33 yr plumber the on/off with the torch drove me nuts but still well done)
@go-diy Жыл бұрын
sorry for the noise!! what happens is, that you do what the owner and the boss ask of you!
@jclockard Жыл бұрын
Why did you not anchor the valves to a 2x4 and instead anchor the piping?
@billdershem67147 ай бұрын
Did you discover that you have to remove the internal plug, when using that diverter as a 2 way, not 3 way, diverter?
@hm-ys4ym Жыл бұрын
steel screws in contact with copper?
@juangarcia-pc7de10 ай бұрын
I installed mine and my hand heal is always on even if i set it to be on shower head.what causes that?
@robertlee4172 Жыл бұрын
4:19....is this for water hammer? I read, this is a temporary solution, as the device gets use with age, it loses it's effectiveness.
@AlanRamirez-xf6jq2 ай бұрын
Can a tub spout be used here ?
@urfasher2 жыл бұрын
Where do you get the pliers to remove the stop ring?
@go-diy2 жыл бұрын
The Home Depot !
@ChillinwitDylan3653 жыл бұрын
I’m currently doing the exact same setup in a clients master bathroom. It’s hard to tell from the video...is there any 3/4” lines in your setup? Is it all 1/2”? Thanks for the great video! It’s awesome to see someone else that takes extreme pride in their work. Don’t sweat the technique!,🎶🎶🔊
@go-diy3 жыл бұрын
it's all 1/2, but it comes from a 3/4 pipe
@RolandoGarciarocky2 жыл бұрын
Can I cancel the right side and use the left side on the transfer valve?
@go-diy2 жыл бұрын
Yes, the operation is the same
@ShootStraight84 Жыл бұрын
Badass but is there a way to mount the diverter on top of the valve instead of to the side ?
@timquick9554 Жыл бұрын
YES absolutely would have saved a ton of offsets (90s) but design layout IS preferential. So to each their own.
@Troy_Sent_A_Message2 жыл бұрын
Anyone know the kohler DIVERTER CARTRIDGE brass nut size? I can't find the tool to remove it, home depot doesn't have it.
@koalaforniapl82262 жыл бұрын
I found it at homedepot! It was in the tool section You have to look around and you will find it
@niskamhsiz4022 Жыл бұрын
Two shower values just to add another shower head? Kinda dump kohler did this. They should just built one valve with an extra output.