Kraton/outcast 4s v2 servo saver fix. losi lmt servo saver

No video

Kraton/outcast 4s v2 servo saver fix. losi lmt servo saver

Рет қаралды 2,755

Жыл бұрын

This video shows how you can fit a losi lmt servo saver into your kraton 4s to rid of the terrible stock servo saver.
parts needed are:
losi lmt servo saver
servo spacers (2mm x6)
m3 x 20mm machine screws
m3 nylock nut
smaller screw to fit saver onto servo

Пікірлер: 27

@VDVC-RC Жыл бұрын

Simply genius! I've looked at those and other servo savers but never got one because they all seemed to be too tall... I totally overlooked the fact that I could space the servo up... If my modified arrma 24t servo saver with the HD Spring doesn't work out, I'll try one of these next... I already have some 25t metal inserts

@JonDuprez 2 ай бұрын

Good looking my man!!!!!

@EXTREMERC416 7 ай бұрын

I did this when someone on facebook mentioned it. Very good idea

@RCforDais 7 ай бұрын

Completely changes how the car turns. I have got another one to try which is the gpm servo saver which doesn't need you to trim the receiver box etc. Will try it out soon to see what I prefer

@FlingingMonkeyPoop 6 ай бұрын

@@RCforDais Have tried the GPM servo saver? Which one did you order?

@RCforDais 6 ай бұрын

@FlingingMonkeyPoop I havnt yet no. I think it was the gpm large I bought. I honestly havnt really had any issues with this setup so havnt tried it yet. I will at some point though

@FlingingMonkeyPoop 6 ай бұрын

@@RCforDais Appreciate the response. I was just wondering if you tried that one. I actually just got the LMT servo saver due to your video. I need to figure out how to attach the steering link to the saver. It is upsidedown to how it would normally be mounted. LOL

@RCforDais 5 ай бұрын

Did you get this working after?

@markhalton2584 6 ай бұрын

I’m going to try a simple fix. Going to take the saver apart and hot glue fill 50% of the spring cavity. This should really stiffen it up whilst still leaving some shock resistance

@markhalton2584 6 ай бұрын

Update. This failed, and I cooked the servo lol

@RCforDais 5 ай бұрын

Lmt servo saver is the way forward

@tyrellcorp2118 5 ай бұрын

@@markhalton2584 Not a bad idea though. Maybe shoe goo? But yeah I’m trying this Losi ss.

@tyrellcorp2118 7 ай бұрын

Thanks for the video. I’m going to try this. I think simple round aluminum spacers will work instead of having to drill out servo spacers. Yes, no?

@RCforDais 5 ай бұрын

Yes don't see why not. Aslong as its spaced up don't really matter how you do it aslong as it's secure

@tyrellcorp2118 5 ай бұрын

@@RCforDais All parts are in, including the servo saver. How tight did you make it? I guess I’ll start loose and tighten as needed, but there’s a wide range. From fully extended to fully tight, how far would you estimate you screwed down?

@RCforDais 5 ай бұрын

@tyrellcorp2118 I think I fully tightened it then loosened it off a couple of turns if I remember rightly

@tyrellcorp2118 3 ай бұрын

@@RCforDaisThis works so well. I ended up tightening as much as I could by hand. I also used 10mm spacers. Even 8mm risked rubbing for me. The turning performance is night and day. Thank you.

@RCforDais 3 ай бұрын

@tyrellcorp2118 yeh personally I would now run more than 6mm myself too. But definitely a worthy upgrade