Hello👋,
Today I am going to 🔥Check Charging System🛵, Clear Fault Codes with Scanner, Change Coil Plate and Check Oil Pressure .
This is one of the procedures we do at Fixer Motos, 👨‍🔧
This procedure applies to almost all Motorcycles that have a Three-Phase Winding, that is, the charging coil is three-Phase.
Subscribe: 👉💝https: // / @fixermotos Sub_confirmation = 1
Apply the procedure to:
Bajaj Pulsar 160 FI
Bajaj Pulsar 200 FI
Bajaj Dominar 250
Bajaj Dominar 400
KTM Duke 125
KTM Duke 200
KTM Duke 250
KTM Duke 390
Husqvarna Svartpilen 200
Husqvarna Svartpilen 401
If you are interested in knowing more about how or where to buy original spare parts or Specialized Motorcycle Technical Service, here are the links
Instagram💛:
/ cristhianpirateque
/ fixermotos
Facebook💙:
/ fixermotos
Link of the Coil Plates
fixermotos.mer...
Battery Link
fixermotos.mer...
Store link.
fixermotos.mer...
.
😱How to CHANGE Motorcycle BATTERY🤯🚧
• Batería NO CARGA❗ Camb...
⛔️OIL CONSUMPTION♨️
• ⛔️CONSUMO DE ACEITE♨️K...
🙋‍♂️HOW TO Change MOTORCYCLE Oil
• COMO Cambiar Aceite Pu...
👀✍️Electrical Parts Check✍️👀
🔋-Battery
Multimeter position
20 V DC
Multimeter Tip (+) on Battery Terminal (+)
Multimeter Tip (-) on Battery Terminal (-)
Empty Value "Nothing Connected" 12.40 V DC to 12.80 V DC
🔋-Battery Charging System
✅The battery must be fully charged ✅
Multimeter position
20 V DC
Multimeter Tip (+) on Battery Terminal (+)
Multimeter Tip (-) on Battery Terminal (-)
Value at 1,500 RPM's 13 V DC to 14 V DC
Value at 5,000 RPM's 14 V DC to 14.7 V DC
🩺-Load Coil Resistance
Multimeter position
200 Ohms
Multimeter Tip (-) (+) on Yellow Charging Cable (1)
Multimeter Tip (-) (+) on Yellow Charging Cable (2)
Multimeter Tip (-) (+) on Yellow Charging Cable (3)
Value at Room Temperature with Coils Disconnected 1 Ohms
🩺-AC Alternating Voltage Charging Coil
Multimeter position
200 V AC
Multimeter Tip (-) (+) on Yellow Charging Cable (1)
Multimeter Tip (-) (+) on Yellow Charging Cable (2)
Multimeter Tip (-) (+) on Yellow Charging Cable (3)
Value at 1,500 RPM's 20 V AC to 35 V AC
Value at 5,000 RPM's 80 V AC to 110 V AC
🧩 Installation 🧩
Verify that the battery voltage is equal to or greater than 12.60V, Secure the terminals with the nuts and bolts, first secure the positive terminal [+] and lastly the negative terminal [-], you can add petroleum jelly to avoid oxidation and / or corrosion.
👌Adjusting torque for screws🤏
-5mm Screws Oil Filter Cover x 2 Units
0.82 kgm
-6mm Screws Oil Filter Cover x 2 Units
1.0 kgm to 1.2 kgm
-Oil Drain Plug
1.2 kgm to 1.5 kgm
-6mm Screws Cover Casing Steering Wheel x 12 Units
1.0 kgm to 1.2 kgm
-Screws 5mm Bristol Plate Coils x 3 Units
1.0 kgm
👀CHECK THE OIL LEVEL DAILY👀
Recommended Engine Oil
JASO MA T903 SAE 10W 40 ✔️
JASO MA T903 SAE 15W 50 ✔️
🧪Quantity 🧪
1,200 ml without filter
1,250 ml with Filter
1,500 ml Total disassembly of the motor
💢-Oil Pressure Test
♨️The engine must have a temperature higher than 60 ° C ♨️
On the thread of the temperature sensor in the cylinder head
Install Oil Pressure Gauge Coupling
Value at 1,500 RPM's Greater than or Equal to 0.9 bar - 14 psi
Value at 5,000 RPM's Greater than or Equal to 1.8 bar - 28 psi
🔎Reference of the parties: 🔍
Original KTM Spool Plate 90139004000
Original KTM Oil Filter 90138015000
Oring Original KTM Oil Filter J770039326
Original Bajaj Flywheel Cover Gasket JL541208
Motul 7100 20W50 Original Lubricant Oil 3374650247410
Greetings!
FIXER MOTOS Distributor of Original Spare Parts and Specialized Technical Service in Motorcycles.