That is really nice. Can pull the front wheels off the ground, even with a loader.

Thanks! I am hoping this manual gearbox is built pretty solidly. Time will tell I guess. I want to build a PTO dyno someday to see how much power I'm making before and after modifications. Try the easy stuff first like advancing the injection timing a bit.

I do wish it had a reverser of some kind, so that it could use all forward gears in reverse.

I have 4 60lb weights which were about $60, plus $20 shipping, each. ~$320, not including whatever I paid for the carriage-bolts and hardware. I got them from TaylorFoundry. Don't order any weights until you know for sure what mounting pattern your wheels have, if any. I don't recall the details, but I do know for sure that the wheels for the ag tires are different. If I had to buy the machine again, I'd go for the R14 hybrid tire. I am satisfied though with my R4s. I like my 2401 a lot. I also like the L2501, but it lacks the mid-pto and the rear pto is 540rpm only (2401 is 540/1000). Good luck on your tractor hunt!

@@zoidsfan77 oh okay, gotcha. Thank you, that’s good to know! You sure know your stuff. Yeah, I have experience with the R4’s on a higher HP tractor where I work, decent tire but for a compact I think I’d like something that digs a little. I’ll have to look into that more. Yeah, the PTO set up on a machine this small is a very nice extra. For the money it’s quite worth it. Thanks!

@@itsmancini Well, the dealer only had a B2601HSD in stock and it was on sale because it sat for a few months. They typically sell large farm tractors and got this to market smaller tractors. Love it though! It’s a great size and am happy with the HST after all.

The width is 48 inches at the rear wheels, and no they are not adjustable. There is a narrow version of this tractor, the B2401N. I don't know it's specs, but it is narrower than mine.

Yes all the loader work was in medium. The road stuff was in high.

Great video!

They are TF655 wheel weights from Taylor Foundry. I used two in each wheel, 60lbs each. I mounted them using eight 18-8 Stainless carriage bolts, 1/2"-13 thread, 6 1/2" long, along with matching stainless flanged locking nuts. The weights made a big difference. My tires are just plain air though.

@@zoidsfan77 could you fit 3 of the TF655’s on each wheel? Would 3 even be necessary?

@@theWortMonger You could, but 2 is the most you can put without sticking out significantly past the edge of the rim. It may be a challenge to find carriage bolts long enough.

Interestingly, someone else asked the same question in another comment only 3 hours ago. I will paste the relevant part of my reply to them: Increasing the limiter is a very easy engine adjustment, but I recommend caution. Firstly, increasing the engine speed also allows you to over-speed PTO implements, which depending on the implement can be very dangerous. Secondly, it is possible to adjust too far and overrev the engine. I set mine to 3,000 which I feel is well within design limits for the engine. Kubota makes D1105 engine variants up to 3600 rpm for generator service. Thirdly, it could effect you if you have any engine related warranty claims. If you look at the right side of the engine you'll see the injection pump. Operate the throttle and observe the linkages. It will be obvious how it works and what you will have to adjust to increase the RPM limit. Disconnect the linkage from the pump and operate it by hand until you set the limit screw to the setting you want. When reattaching the linkages you may have to install it in a different hole on the lever, and adjust the nuts at the end of the linkage rod. You want it so the lever rests against the low-idle stop when no throttle input is given, and maxes out against the limiting screw when at full throttle. At full throttle you don't want the throttle rod to have too much force on it, so adjust such that with the floor pedal floored it just reaches the limit. I would also not recommend adjusting the RPM limit on a new machine until it is out of it's engine break in period (50hrs per Kubota) and has had it's first oil change.

Thank you! I have 170hrs now on mine and feel comfortable making the adjustment. Funny that when I told the local kubota dealer that I was not reaching full PTO rpm (below the arc under load), they just said sorry, it’s set at the factory and we don’t touch it.

If you are not reaching full rpm under load at factory settings than it would stand to reason that your load is too great for your size tractor.

So far so good. Really only two things have gone wrong. The backhoe valve developed an internal leak and was replaced under warranty, and later on one of the power-beyond quick connects (for the backhoe) had developed an internal restriction and caused some problems. I replaced the connectors with flat-face style couplers and they've been great. Overall it's a great machine for me. I do wish it had a bit more PTO horsepower, but that's not the fault of the machine but rather this size class. I plan to install a big engine oil cooler and do some engine mods eventually (I can't leave well-enough alone).

I have. The backhoe works well for that, although it is not pictured in this video. I also have a 3 point post hold digger. It's not a big tractor, so digging large stumps will take some time and planning, but I've done it.

Hey what did you do for a 3rd function / remote rear valve?

@@smoothdurban The 3rd function valve for the loader is Kubota part B1653. I do not currently have a rear remote on this tractor, although I'd like to install one in the future. There is the rear "power beyond" circuit for the backhoe though, and comes as part of the backhoe install. Hopefully that was helpful.

@@zoidsfan77 that kits is coming up as only for the 2301 and 2601. Were there any differences to adapt that kit to the 2401?

@@smoothdurban Yeah now I remember there was some trouble as the loader handle is different. The dealer had a lot of problems installing it, all handle related. If I remember correctly they had to use the handle from the kit for the B2650 hydrostatic tractor.

Yes it can, but because the tractors gearing is so low it is more difficult to do at lower speeds in lower gears.