#welding #weld #weldingtipsandtricks #weldingforbeginners #weldingtechnique #weldingtechniques #weldingtricks #cutting #cutting few know the trick of cutting a square tube for a 90 degree joint with precision results
За пять минут видео эту трубу можно перепилить в ручную и более ровнее! Без таких мучений как на видео!🤣
@gidesp1 Жыл бұрын
Merci beaucoup.
@user-pz7qm9gf3y8 ай бұрын
Ótimo trabalho
@St.Eg. Жыл бұрын
С такой скоростью работы рама для стола будет неделю делаться, слишком много лишних движений. Ещё бы над дикцией и постановкой речи поработать, и перчатки использовать без дырок
@sevaxe4013 Жыл бұрын
Он так делает чтобы детально всё показать, а так по жизни уверен делает всё быстрее на автомате...
@videopipeline6419 Жыл бұрын
...or in a tiny fraction of this time, you can use a miter saw with metal cutting blade.
@januszmodzelewski4807 Жыл бұрын
Jak ktos ją posiada i umie ustawić ...
@ahuachapan210 ай бұрын
The results are excellent, however the disk only last a few cuts. I try with 7 inches Diablo brand and only last like 20 cuts. 20 cuts for 30 plus USD disk is too expensive.
@SaleemAhmad-xl2xp29 күн бұрын
You are a great man shabash
@crudeliocastillejoscrudo825510 ай бұрын
Yo mejor con una segueta todo el corte, se me hace mucho más rápido y no fastidio tanto a los vecinos con el ruido ya que donde vivo solo se permiten en el día 55 db en el interior de la casa con todo cerrado y esa cortadora los sobrepasa por más del doble, me la pasaría a puro reporte y demandas. Saludos.
@washingtonicm Жыл бұрын
Muito bom 😊🇧🇷🇧🇷
@machineman58 Жыл бұрын
MasyaAllah. Sngat detail informasinya
@anvikel5907 Жыл бұрын
Tremendo método... ese es el que todos usan.
@trickswelder3839 Жыл бұрын
Terima kasih👍
@rizamaya2393 Жыл бұрын
Profesional mantap👉👍👍👍🤗 bosku
@jacksonmayyattil33085 ай бұрын
Thanks for helping broo❤❤
@Peppa.Animal Жыл бұрын
i love your ideas, make more videos about them
@kuliwelding7056 Жыл бұрын
Thanks brother
@user-eu5ti1qp2f Жыл бұрын
Я за это время уже изделие изготовлю)))
@andreymatuznyj1043 Жыл бұрын
... покрашу и продам...
@user-jr8nz7ur8b Жыл бұрын
Тоже самое что и уголок.тут нет секретов совершенно. И велосипед тоже давно изобрели
@KULIWELD Жыл бұрын
Channel baru sedang menyimak jhonk 😍😍😍
@Papa_Kemsu Жыл бұрын
Cảm ơn bạn.
@zapadlo74778 ай бұрын
Что не придумаешь ради того чтобы замедлить процесс,)))
@saidrebia1179 Жыл бұрын
Slt très bon travail continue
@NodirAxrorov-nk4pj5 ай бұрын
Ххххххх
@76kdv3 ай бұрын
Маэстро и этим же кругом зачищаешь? Браво! Если надо 20 по 45 на профиле 100*50? Тож так?
@IRONMAN-xo4ek8 күн бұрын
Нужно делать на 5мм меньше от нужного размера .припуск по 2.5 мм зазор на каждый угол для провара.А так будет валик от сварки.
@josvandiepen3425 Жыл бұрын
A cutting disc is not to be used for grinding operations! Read the instructions on the disk!
@superzeery7824 Жыл бұрын
Imao
@MalawiToday11 ай бұрын
Exactly, yoo dangerous
@Rafael-ed8ym10 ай бұрын
O disco é dele... O video é dele... Ele faz o que ele quiser 😂
@stevenm76929 ай бұрын
I use flapper discs to cut with!
@reymondjosuearguellorojas25198 ай бұрын
Is very dangerous
@juliuskpwa44122 ай бұрын
How can I prevent my eyes when working please I always feel pain each time I was work in my eyes
@Serega_Strizh Жыл бұрын
И такой заварим, хрен не лезет, не зазор😂
@yuyunyunengsih2105 Жыл бұрын
Kalau saya. Motong 9p derajat cukup 2 garis aja sidah presisi. Cara seperti itu selain boros alat juga lambat
@Wil-Mac Жыл бұрын
Good idea
@ChiefShamanАй бұрын
This video gave me cluster headaches
@user-pu3fy4kx1q Жыл бұрын
Зазор не позор,а вообще пользуйтесь чертилкой удачи
@ziauddin794824 күн бұрын
good angular steel pipe cutting # 👍🇵🇰
@antonyvalentim9710 Жыл бұрын
Usando o disco de corte pra desbastar?
@biankut Жыл бұрын
verdade, n pode.
@user-rb4uj4ei8n Жыл бұрын
Для хорошего сварщика зазор не помеха
@charlesmaverick-im8nd7 ай бұрын
Sempre dá k gada mesmo, se cortar direto do 45.
@tukanglaslahat Жыл бұрын
Bang sarung tanyanya baru ya
@cuuvoduc9285Ай бұрын
Tuyệt vời quá
@Longterm-ue8ew4 ай бұрын
ยอดเยี่ยม
@roman_zchukov Жыл бұрын
Сделай 4 таких угла и свари квадрат, чтобы диагонали совпали и 4 угла были по 90 градусов.
@demyandiatlov8545 Жыл бұрын
Боюсь не скоро у него получится
@patehkreatif Жыл бұрын
Hadir bosku.
@SmIgorek Жыл бұрын
Может под углом 45 градусов?
@OBEDTHMIRAFLORES3 ай бұрын
Perfecto.
@user-qy9mz4hw2d Жыл бұрын
😂мдддаа!вот это мастер😂😂😂
@katzchenundloup669312 күн бұрын
Doing it this way taking that much time, the steel could rust away during the procedure...😆
@ricardomartinezmoreno8557 Жыл бұрын
Siuuuu!!! Secreto!!!! Me horroriza que lo saquen a la luz!!! Nos quedamos sin faena, ahora cualquiera puede!!!
@haiduong4545Ай бұрын
This tip should be taught to every worker
@user-kb3ix9ld1h10 ай бұрын
Когда очень много свободного времени и нечем заняться, самое то.
@ajiezm9252 Жыл бұрын
Mantap 👍👍
@micpep8 ай бұрын
You're talented but... I want a cut off saw!
@user-yn4jy6lf9j Жыл бұрын
Если делать один угол тогда можно высунув язык от удовольствия, подтачивать микроны. А если углов десятки?
@user-mn3vh8jx5d4 ай бұрын
Очень высокая производительность!!!!!
@ryanwebster24709 ай бұрын
I was more interested in the music
@jefflyon10023 күн бұрын
I get the idea but if I'm building something using tubing I always keep the seam line on the inside or whatever hides it best from view. Especially on thicker tubing, having your seams run on all different sides of the project looks sloppy and unprofessional. The tibe seams are visible even when painted. Just one view I guess.
@bosazkaofficial84762 ай бұрын
Kelama. N bang langsung aja satset
@likausrcu3644 Жыл бұрын
IMAS SUPER KOŽNE RUKAVICE😊😂😂
@BeyourselfandIwillto6 ай бұрын
An easier way is knowing that a 90 degree angle is two 45 degree angles coming together. So, if you cut one at 46 and one at 44, it will make 90 degrees.
@mrmihaiuc4 ай бұрын
Tought the same thing but the idea its to preserve one of the original layers and just so the one in the exterior its more durable
@marcocalderon321411 ай бұрын
Mucho proceso
@John631864 ай бұрын
so doing it very, very, very slow is better. Also wear wool gloves probably gives a better result.
@lucasmatos100911 ай бұрын
Compra um policorte...
@charlesmaverick-im8nd7 ай бұрын
Mazááa fu Dido!!
@myworkaf3516 Жыл бұрын
Good
@maxwellmussa6970Ай бұрын
That's very true if you have small job ,but what if you have a big job it can take ages
@gsp9115 күн бұрын
By the time you're done, it's rusted through and you can start over.
@bryanwanek46 Жыл бұрын
Fine if I have all day to make a couple of joints.
@isidroledesma6373 Жыл бұрын
Con todo respeto señor.... Usted da muchas vueltas para un simple corte de un tubo estructural en ángulo de 45°. Con su técnica seguramente va a tardar 6 meses o más para terminar un sólo trabajo. Calificacion: 0 ESTRELLAS
@aviavinash58532 ай бұрын
Yek cutting ko 5 minute karega tho hamara boss hamko jaldi bhagayega😅😅
@user-iq3gk5ly2w27 күн бұрын
вот так и бывает, когда начальник оплачивает работу по часам! хрен ли спешить , к концу месяца квадратная рамка будет готова! правда будет напрочь сточены сотня - другая дисков, заношены 30 пар перчаток !
@user-es3xu3pj6v6 ай бұрын
Ребята, это всё - шляпа. Здесь нужна торцовочная пила или ленточнопильный станок. У меня всё. Не благодарите.
@chonburi45610 күн бұрын
เป็นใบ้เหรอครับ ทำไมไม่พูดให้คนดูเขาเข้าใจง่ายๆ
@user-bd9ju8fc4n Жыл бұрын
Даремна трата часу на такі тончаки. Зварювати всеодно потрібно з зазором для провару. Так "вилизувати"мікрони,там де вони не треба ,можуть ті,в кого багато вільного часу.
@Vubaothanh Жыл бұрын
Trời, làm thế này cả ngày được một vết cắt à, thợ thuyền làm kiểu này chết đói
@rickcarhart8892 ай бұрын
New invention out there called metal chopsaw
@zoranmicic716216 күн бұрын
OK. Sledeci raz Bude brze
@anthonyhemmings1601 Жыл бұрын
Did it really take you a third of the entire video to mark that one angle!?
@micpep8 ай бұрын
He wanted to make shure you understand so he took his time! 😂
@juliusceasarcinco3478 Жыл бұрын
1 day 1 joint..hehe
@tomthompson74006 ай бұрын
ok ,,, it got ground back to the same line and angle it would have got cut at in the first place ,,, what did I miss ,
@michealstonecipher91029 ай бұрын
It doesn't show how to make the opposite cut. That what I'm not good at.
@jstrawse Жыл бұрын
yea welllll those wheels were not designed to grind on the side of the wheel only for cutting
@cutitv2229 Жыл бұрын
Hướng dẫn thì ok chứ làm cái cửa mà cắt kiểu này biết bảo giờ xong
@user-nk3yz8uj9e Жыл бұрын
👍👍
@pb1910 Жыл бұрын
มันท่อตรงไหนละมันคือเหล็กกล่อง ทำไมจะตัดไม่ได้
@polsrimasittikul890 Жыл бұрын
👍👍👍
@mvicunax Жыл бұрын
👍👍👍👍👍👍👍👍
@user-qi6cn6yl6r Жыл бұрын
Супер
@drycreek32044 ай бұрын
Just use a metal cutting miter saw!
@daedalus547 Жыл бұрын
This is irrelevant, it doesn't matter if the tube doesn't line up perfectly, along as you make sure it's 90 degrees when welding it doesn't make a difference cause when you make a pass (not tick it all the way a round) you are adding material. So you can fill those gaps in just by adding more filler to the spot.
@georgerusu84238 ай бұрын
it matters if in general the weld pulls or tenses the metal, the 90 degree angle can be affected....for a square pipe, the wall thickness can be used in an uninterrupted joint in this way when welding, the metal is in a fixed position
@daedalus5478 ай бұрын
@@georgerusu8423 Metal always pulls, thats why we clamp our work piece! The metal should always be in a "Fixed" position, I have yet to see any one certify floating welds. This is basic welding 101, no matter what tube your welding, the tube will move to where the heat is, thats why we clamp it in a jig, vice or whatever else you have that can secure both lets of angle, its secured, tack it in the middle of each side and weld from then, that way you can wrap the corners and make a nice strong weld.
@nickmcnellis3937 Жыл бұрын
Now weld it!
@stephanebucari8800 Жыл бұрын
1 reproche : le feutre est trop gros (utiliser une pointe fine ou pointe à tracer ) ,2 ème : pourquoi faire un deuxième trait à l'intérieur ,c'est une perte de temps , il suffit de tenir la meuleuse inclinée, imaginez que votre tube est du 100x100 x 4 est que vous devez en couper 6 mini ,la fièvre . Egalement de préférence utiliser un disque de 1 ou 1.6 mm d'épaisseur
@biitamachanel2389 Жыл бұрын
Biasa las di docking
@sabda_alam_asmr Жыл бұрын
Good 👍👍
@user-mn3vh8jx5d4 ай бұрын
Надо было кистью малярной отчеркивать😂
@josemartirmejiamejia61193 ай бұрын
One Year for do a gate 😅
@herryyasin64108 ай бұрын
Terlalu lama kerjanya😂
@user-rx4mj8zj4w6 ай бұрын
Один угол будеш делать 1 день
@emuemu719 Жыл бұрын
เสียเวลา
@kewakl8891 Жыл бұрын
of the millions of craftspersons in this world, only a few know this. I declare this to be false!
@paysorchannel2729 Жыл бұрын
Hmmm
@tims.4969 Жыл бұрын
Sorry, but that's not a TRICK. Nice work dude, but no trick.
@user-rh8yo8ts8y5 ай бұрын
Вопрос спецам. Судя по видео, да, все хорошо, ровно красиво. Конечно, такой угол - "лицо" профессионала. Но суть вопроса. Не проще ли, относительно быстро обрезать, пускай где-то небольшой зазор, а потом просто проварить. Понятно, что может шило на мыло, сварка может занять больше времени, но если аккуратно зачистить, то на финише одно и тоже. Просьба без троллинга, по делу.
@marcianocalette6966Ай бұрын
Puras tonterías
@user-wl4pi8qo3f6 ай бұрын
надо было с самого начала не резать,а стачивать (идиот)