I would like to introduce how to make a tool for Riveter Bolt and how to use Riveter Bolt. #Amazingtool #Riveterbolt #kwandotechnic Please subscribe, like and share my video. Thank you so much!
Пікірлер: 30
@MarcosAurelio-dj6zy11 ай бұрын
👏👏👏
@eltonm.t.8733 жыл бұрын
Nice tool, the best design I've seen!!! However, I would leave the bolt head so that I could use a battery powered impact screwdriver instead of old fashioned corded drill. Also, I would devise a way to be able to change the screw tip to drive different rivet nut sizes, the screw tip could be Allen screws of different sizes/gage 'cause they are much harder and less prone to thread damage.
@KwandoTechnic3 жыл бұрын
Thanks for your advise!
@davidschwartz51272 жыл бұрын
You would be surprised, I always had that same assumption about Allen bolts, until I need to drill on out they are the same unless you by the as grade 5 or grade 8.
@gatpawgatpaw47704 жыл бұрын
Nice build. May consider using cutting oil when drilling to make the process easier and protect the drill bits.
@KwandoTechnic4 жыл бұрын
Many thanks for your advises!
@MrJamesoro3 жыл бұрын
como se llama ese tipo de chazo? excelente video
@KwandoTechnic3 жыл бұрын
Thank you so much!
@giovannisampalmieri21383 жыл бұрын
scusa se contesto il tuo operato, ma come può il dispositivo e di conseguenza il trapano allontanarsi dallo scatolato dove hai inserito il rivetto se il mandrino del trapano gira in senso orario. una volta inserito il rivetto, il mandrino del trapano dovrebbe girare in senso antiorario. questo dovrebbe avvenire nei minuti 9:30 e 9.31. correggimi se sbaglio.
@KwandoTechnic3 жыл бұрын
When removed, it will rotate in the opposite direction
@bruynemarina60744 жыл бұрын
Well done! Great build and very useful with this tool.
@KwandoTechnic4 жыл бұрын
Thank for your opinion!
@davidjames1063 Жыл бұрын
Only problem Material wise, Grade 8, or better nuts and bolts should be used.
@hyperhektor77333 жыл бұрын
what gas / gasmixture do you use for the welding?
@KwandoTechnic3 жыл бұрын
Argon gas.
@nagarandempire3261 Жыл бұрын
Does anyone try this tool
@POULPY474 жыл бұрын
Thanks à lot ! You're working very well! What's type of TIG you're using?
@KwandoTechnic4 жыл бұрын
This is my welder. You can order on it: bit.ly/30T55h0
@POULPY474 жыл бұрын
@@KwandoTechnic thanks a lot!
@KwandoTechnic4 жыл бұрын
You are welcome!
@POULPY474 жыл бұрын
@@KwandoTechnic were do you from , you seem very sympathetic ! Hello from France !
@KwandoTechnic4 жыл бұрын
Where I am no important. I respect everybody. I want to support everybody as I can.
@cameronhadley61263 жыл бұрын
are you kidding me?
@KwandoTechnic3 жыл бұрын
No, thanks!
@user-wr2vd9qg1r4 жыл бұрын
зж
@BillSmith-kl7sb4 жыл бұрын
lol grossly over engineered. I just use a High grade bolt, washer and nut drive socket on a drill. Hit the bolt with wd40 and it pulls tight in a few seconds. Why all the pipe and crap in between lol.