I modified my Baofeng BF-888S with a chinese Li-ion Micro USB charging board from Ebay. This way i can charge my 888 just as easy as a mobile phone or use with a powerbank.
Пікірлер: 70
@raptr496 жыл бұрын
Thank you for this great idea. I left the 1.22 k resistor in place. The charge current was 0.8 Ampere, which the battery should be able to handle fine. Also, I used epoxy to make a backstop for the PCB so it would not slide back over time when the charge cord is plugged in.
Very helpful, thank you. My charger broke (some component melted) so I replaced the circuit as you did. Easy peasy
@laagvliegerv67 жыл бұрын
Great! Nice the video was helpfull to you.
@allanalvarado4119 Жыл бұрын
Nice mod to the battery...now it can be charge from a power bank...
@attilarivera5 ай бұрын
thank you ! 👏👏👏👏👏
@Mr_Meowingtons6 жыл бұрын
dude that is brilliant!!!
@juanfredjimenez6530 Жыл бұрын
Hi.I wish to see some trouble showing and using an oscilloscope for repair.
@baobad123 жыл бұрын
Will it be possible to use it in 12v of the cigarette case of the cars?
@dekegels5 жыл бұрын
just a question doesnt it produce heat? like right next to the battery?? is that a good idea?
@laagvliegerv65 жыл бұрын
Its not producing any heat. When you touch the chip you feel it is slightly warmer then ambient. No problem.
@kairoyoyo45745 жыл бұрын
If i want connect the +ve and -ve wire to this charging board,did i need to change any connection at the battery or just connect it to the board?sorry i not very familliar with circuit or thing like this
@maniacse7 жыл бұрын
Wau man, I remember, when we talked about this a while back. And as I see, we bought same unprotected boards, both. Just yesterday I made my second battery, and this time with protected board. But I have to tell, that light "pipe" you made is awesome. I just turn the board and made two holes on back, and separate LEDs by using Sugru. I will put photos on my GooglePlus page, check 'em out, if you want..
@laagvliegerv67 жыл бұрын
Yes haha! Nice how we can help each other with new ideas. I saw some of your pictures. I like the key's you glued in to weight it down ;)
@maniacse7 жыл бұрын
Yes, that one. It was made for my friend, he wants to use it both in car and home, but do not want to rework battery as I did. I tought it is too light for car use, so only thing came under my hand was set of old keys. Since then I use 'em as weight also for my soldering iron stand..
@laagvliegerv67 жыл бұрын
Nice! You also have a nice Car, The Opel Frontera. I drove and maintained them a lot at work
@maniacse7 жыл бұрын
Dont even talk about that car.. It is for sale. It is beautiful piece, but I have big trouble with that 2.5TDS VM engine. I invest so much money and effort to that engine, and it still doesnt run good. I have enough. Hopefully somebody with passion in cars will buy it and make run again.
@laagvliegerv67 жыл бұрын
Haha the car is ok But those VM engines are known for troubles. In the Netherlands they all came with the 2.2DTi engine. They are ok. I hope someone will buy it from you!
@REVIEW_JUJUR7 жыл бұрын
My Baofeng 888s battery is 2800mAh instead of 1500mAh, can i still do this mod???
@laagvliegerv67 жыл бұрын
As long as it is a single cell 3,7V battery
@abdulkhalekshaikh4028 Жыл бұрын
Baofong harjing cradalburn out how can i repair ?
@toddhayslett82697 жыл бұрын
which charging board did you use I see some TP4056 boards is this the right one?
@laagvliegerv67 жыл бұрын
yes it is!
@sircyfus9478 жыл бұрын
Good Job. Did you check the value of the input side of the battery board though? I'm wondering if its really 500ma or more.
@laagvliegerv68 жыл бұрын
+Sir CyFus I Didn't check the output. The datasheet of the charge controller IC contains a list of resistor values for the PROG pin on the IC with their current settings.
@sircyfus9478 жыл бұрын
+laagvliegerv6 I measured the current from the charger board to a half dead battery. Its 800ma
@laagvliegerv68 жыл бұрын
+Sir CyFus Which resistor do you have on the PROG pin?
@sircyfus9478 жыл бұрын
The one rated for 1000ma, I need to do more testing and change the values to confirm
@wheelbarrow2803 Жыл бұрын
Is it practicle to have one charge controller feeding the one on the battery? Wouldnt you just need to pass throuogh the usb power to the back of the leads that have already been provided?
@laagvliegerv6 Жыл бұрын
There is no charge controller in the batteries. Just the cell protection pcb.
@wheelbarrow2803 Жыл бұрын
@@laagvliegerv6 you sure it’s not a 1s bms?
@laagvliegerv6 Жыл бұрын
@@wheelbarrow2803 im sure. It is not a BMS. Just simple under and over voltage protection..
@nightanday_782 жыл бұрын
Se vai direttamente con il + e - della micro usb sul caricatore originale, mantieni tutte e due le possibilità di ricarica. Io l'ho fatto, il risultato è poterla usare anche con l'alimentazione 220 - 12. -5 volts
@ianadkins-25304 ай бұрын
That's going to let a lot of damp into the battery with all the resulting corrosion.
@laagvliegerv64 ай бұрын
We are now 8 years later. Radio is used in a workshop. Cold at winter hot in the summer and wet when raining....the Radio and battery still no corrosion and just working fine. Battery has lost some capacity over the years and the Radio itself has a noisy scratchy volume knop potentiometer. So the damp story is a bit BS. The original battery isn't sealed very wel neither.
@udhi_gn389317 күн бұрын
What corrosion? I had a roughly similar tp4056 usb charging mod on my 888s and it's going for 6 years now and guess what, no corrosion. You're outvoted! 2 to 1! This kind of mod is no big deal unless the humidity is 100% all day or you're swim a lot with it.
@SexyBigDancer4 жыл бұрын
compra un atril para el celular por favor . Gracias por la idea . Saludos
@MontajciKopekАй бұрын
how i make this on baofeng uv5r and uv82?(after 8 years)
@laagvliegerv6Ай бұрын
@@MontajciKopek the UV82 has a 7,2V dual cell battery. So you can t charge it with this one cell charging board. You need a BMS for balanced charging the 2 cells
@MontajciKopekАй бұрын
@@laagvliegerv6 but, Isn't there a circuit similar to it in it?
@abcdefg33868 жыл бұрын
Is this the original battery or did you change it to a smaller one, so you could fit the pcb inside?
@laagvliegerv68 жыл бұрын
This is the original battery! There is plenty of room inside the case.
@maniacse7 жыл бұрын
my second one (not sure, if it was from 777 or 888 model) was even smaller (yeah, thicker but shorter, so I use battery itself like board support when pluging USB plug in)
@soldeerboutje7 жыл бұрын
Ik ga het ook proberen. ik heb net een printje besteld via eBay.
@laagvliegerv67 жыл бұрын
Succes!
@soldeerboutje7 жыл бұрын
Thanks fot the Tutorial! Now where is the Tutorial "how to open the batterij case" :) Best Regards and 73's!
@laagvliegerv67 жыл бұрын
Ha! Dat is niet zo moeilijk. Ze zitten gewoon in elkaar geklikt met een beetje lijm ertussen. Dus met een dun schroevedraaiertje of een mesje kom je een heel eind. Ik heb het gedaan met zo'n metalen spreider/spudger/prytool. 73s! *That's not that difficult, The battery is just snapped together with a tiny amount of glue between. So with a small screwdriver or knife you its easy to open. I did it with a metal spudger/prytool. 73s!*
@soldeerboutje7 жыл бұрын
Het is gelukt. Ik heb de connector aan de zijkant gedaan zodat de porto gewoon rechtop kan blijven staan tijdens het laden...
@laagvliegerv67 жыл бұрын
Goed bezig!
@entozoon7 жыл бұрын
Take off the little white sticker, unscrew and then it clicks apart if you lever it
@TheOklep8 жыл бұрын
Hello. Does it have also some overcharging protection, so it will not damage the battery? Nice work otherwise
@laagvliegerv68 жыл бұрын
+TheOklep Yes it does. It has a Li-ion charge controller chip on the PCB. It's the TP4056 IC which controls the charging proces.
@maniacse7 жыл бұрын
in fact, board you use is not overcharge/over discharge protected. It is just, as you wrote, charging controller chip. But there is new board style available with both protections.
@laagvliegerv67 жыл бұрын
You got two things mixed up. The Charge controller chip (TP4056) regulaytes the charging proces. So the starting end stopping of the charge when the right voltage is reached, The protection IC's are just short circuit and overload protection IC's and a very crued charge cutoff. They are important BUT!! the Baofeng battery's already have them inside the battery. You can see it when you peel away the capton tape. There is a little PCB with exactly the IC's that are on the charge board you have. When ordering Lithium cells you can choose them order them with or without protection. Baofeng did the right thing and ordered them with protection,
@maniacse7 жыл бұрын
:facepalm: You got me. I do not know, what I was thinking last night... And yet, no alcohol was involved.. :) You are absolutely right. Sorry for confusions, youtubers..
@BAKKER27277 жыл бұрын
charging gaat 220v in er kom uit 22v dat is niet goed voor de cell 3,7V battery nu ook maar usb er op en powerbank super
@laagvliegerv67 жыл бұрын
Waar komt 22 volt uit?
@BAKKER27277 жыл бұрын
oplader naar de batterij toe 22V DC en hij werd warm voor je het weet brand je huis af wat een gevaarlijk oplader dus nu alles op5v perfect BEDANKT VOOR JE TIP SUPER
@laagvliegerv67 жыл бұрын
Ah de originele lader. Ja dat is echt troep.
@SangNguyenOfficial5 жыл бұрын
Tôi đã làm thành công Xin cảm ơn bạn
@mikesey16 жыл бұрын
Why bother with all this when you can just plug the radio into the USB socket of a phone charger? 😀
@laagvliegerv66 жыл бұрын
Mike C what do you mean? this mod is to charge them with a phone Charger. From Factory you can't.
@mikesey16 жыл бұрын
laagvliegerv6 I charge them with my phone charger, just by plugging the cable from the radio to the USB socket on my charger plug!
@laagvliegerv66 жыл бұрын
Mike C you mean the programming cable? The one that plugs into the speakermike jacks?