Laser Poor Cut | Fiber Laser Poor Cut | Over-burning Cut

Laser Poor Cut | Fiber Laser Poor Cut | Over-burning Cut | Solutions of Laser Cut

Рет қаралды 10,015

2 жыл бұрын

Our Store/Nuestra Tienda: spierlaser.en.alibaba.com
Contact: +86-13335151833 clara@spierlaser.com
The video says one of the laser poor cut, fiber laser poor cut, the over-burning cut. You can find the conditions and solution of laser cut overburning.

Пікірлер: 34

@shubhashrisokki.4375 2 ай бұрын

Helpful ... thank you

@thefrenchneco 2 жыл бұрын

As usual, very helpful. Thank you!

@ClaraChai 2 жыл бұрын

You are 🤗 welcome

@ijazmughal8494 Жыл бұрын

As usual Very helpful.👍

@ClaraChai Жыл бұрын

😀 thank you.

@saaww33 2 жыл бұрын

we love you ❤️

@ClaraChai 2 жыл бұрын

Thank you

@hasanudin617 Жыл бұрын

Apa penyebab head laser panas?

@sounthavilaylomthongdy4646 Жыл бұрын

How to clear alarm 4limit

@medjoui7600 2 жыл бұрын

Thank you What about the frequency of a laser source? I think it even affects the burning, if it is a high frequency

@ClaraChai 2 жыл бұрын

From my experience, frequency is not a parameter changeable often.

@medjoui7600 2 жыл бұрын

@@ClaraChai Thank you very much, but what is the effect of frequency if it is too high or too low?

@RotabSe Жыл бұрын

Thanks, Do you have any information about cutting 2mm stainless without N2...only with air...pressure?, etc?

@ClaraChai Жыл бұрын

Could you check my another video, the parameters?

@mstranger195 2 жыл бұрын

Hi Clara . you didn't upload the focus tutorial video?

@ClaraChai 2 жыл бұрын

Later

@mstranger195 2 жыл бұрын

@@ClaraChai Ok . Thank you very much for your videos , that you share knowledge.

@kapechkong4343 2 жыл бұрын

how do we find the correct focus for Mild Steel for example for 4mm 5mm 6mm 8mm and so on. Is there any rule for that?

@ClaraChai 2 жыл бұрын

Reference and experience

@hariharankannan Жыл бұрын

Hi mam we use ispri laser head auto focus head but when I cut carbon steel with air like 3mm the focus position automatically going to -30 after coming alarm servo

@ClaraChai Жыл бұрын

+86-13335151833, please give me more.

@kacpertargas741 Жыл бұрын

Will it be the same for cutting stainless steel?

@ClaraChai Жыл бұрын

I don’t think so.

@kacpertargas741 Жыл бұрын

@@ClaraChai Thank you :)

@astitavsharma1238 Жыл бұрын

Hi, please help, I was watching your videos. I am cutting Galvanized sheet of 0.8mm thickness. Now a days there is lot of slag formation at nozzle tip which is causing cutting problem. Please suggest how to rectify this problem. As there was no such issue while cutting galvanized sheet.

@ClaraChai Жыл бұрын

Parameters not changed? Is the nozzle hot? Is your lens checked?

@astitavsharma1238 Жыл бұрын

@@ClaraChai Lens is perfect. Parameters are fine. Still at nozzle tip slag formation is happening inside the walls of nozzle

@ClaraChai Жыл бұрын

@@astitavsharma1238 Your laser beam is not in the center.

@astitavsharma1238 Жыл бұрын

@@ClaraChai we have cross checked the laser beam centering. That is fine also.