No video
Pierce in Fiber Laser Cutting | Perforation in Laser Cutting 1
Рет қаралды 11,117
Күн бұрынOur Store/Nuestra Tienda: spierlaser.en.alibaba.com
Contact: +86-13335151833 clara@spierlaser.com
The video will talk the "Pierce" in fiber laser cutting and perforation in laser cutting. There are two videos "this video and next video".
Our first question is why we need “Pierce”. Perforation quality can easily lead to cutting and processing good or not, especially in thick metal cutting. In general fiber laser cutting, most of the time, we won’t start cutting from the edge of metal plate. So we need to punch a small hole in the plate and then cut from it.
@DEARRAEDDEAR Жыл бұрын
The best laser settings videos on KZfaq! Thank you!!
@ClaraChai Жыл бұрын
Thank you
@stevemanley264 2 жыл бұрын
I love your videos. They are very helpful. Thank you!
@ClaraChai 2 жыл бұрын
Thank you
@christopherjoyce833 Жыл бұрын
Your a delight to walk and always informative
@ClaraChai Жыл бұрын
Thanks
@sahilyadav998 Жыл бұрын
Hi Clara, I just found your channel and just love how informative your videos are. Thankyou and hope your channel gains a lot more followers.
@ClaraChai Жыл бұрын
😊 Thanks a lot!
@kshitijsalunke8443 4 ай бұрын
Please make video on cutting part hole and size variation
@ClaraChai 4 ай бұрын
part hole? what kind of? Could you offer me a picture.
@dalecollison791 2 жыл бұрын
Thank you for the videos Clara they are very detailed. I think the slower piercing method is good for me and I will try today as we have normally a large hole and spatter. Can you do a video on the best gas, nozzle, parameters etc to cut galvanised sheet please? We have trouble with getting a clean cut as there is always dross on the back! Very annoying. We have tried everything! Please help ❤️👍
@ClaraChai 2 жыл бұрын
There is a video telling the all parameters, including galvanized sheet, please refer to it.
@dalecollison791 2 жыл бұрын
@@ClaraChai thank you. I couldn't find it, can you please send link?🙂
@user-vm9qi1yt5c Жыл бұрын
@timwalter1381 Жыл бұрын
Hello Clara I am wondering if it is possible to set up five stage pierce we only have 3 stages enabled in cypcut thanks
@ClaraChai Жыл бұрын
It is up to the version of Cypcut
@kadirakalp3606 5 ай бұрын
Hi Clara, thank you for effort. Can you please add a pierce parameters?
@ClaraChai 5 ай бұрын
Er, you could find the reference data from cutting parameters videos.
@alexvalean2731 2 жыл бұрын
Hi Clara, thanks for your videos are very helpful, in the specific video you can find the list of parameters for Pierce but I can't find it can you help me !?I would be very grateful if you could help me with a list of parameters for cutting and Pierce. Thanks !
@ClaraChai 2 жыл бұрын
Alex, thank you. There is a video showing the parameters from 500-8000W:Laser Parameter | Fiber Laser Parameters | Laser Cutting Library kzfaq.info/get/bejne/grNig9N-rdnThn0.html
@foxacoustics 8 ай бұрын
Hi Clara! I am having problems with my pierce height. My laser starts off piercing as programmed at 3mm height but after a few minutes it starts piercing higher and higher. It will eventually end up over 25mm and at that height it is leaving big burn marks about 2-3mm wide because of the focus. If I pause the machine for a few minutes then resume it goes back piercing at the correct height of 3mm but a couple of minutes later it starts getting higher again. Any idea what is happening?
@ClaraChai 8 ай бұрын
Is your nozzle getting hot and hot?
@foxacoustics 8 ай бұрын
Yes. I've checked both lenses, they are clean. I've put tape over the nozzle and the hole is in the center. I'm not sure why its getting hot?@@ClaraChai
@Nessy.. Жыл бұрын
I would like to know how to pierce 3mm aluminum on a 1500w laser to reduce back reflection up the fiber and causing damage.
@ClaraChai Жыл бұрын
How to reduce the reflection to laser?
@Nessy.. Жыл бұрын
@@ClaraChai Hi Clara with cutting Aluminum it can reflect back and damage the laser. You can reduce the reflection with good pierce. I just don't know what is best way.
@ClaraChai Жыл бұрын
@@Nessy.. The progressive Pierce, multiple stages
@Nessy.. Жыл бұрын
@@ClaraChai Thank you Clara for getting back to me. I will try this
@nannemunnerahihe 10 ай бұрын
Hi clara I have a problem in my machine in piercing ,, my machine is unable to pierce in all thickness,, sometime it is piercing and sometimes it is leaving,, my engineer tried most of the things but they are also unable to track... Why it is happening
@ClaraChai 10 ай бұрын
I cannot tell you a specific answer only by the comment.
@nannemunnerahihe 10 ай бұрын
@@ClaraChai I have 3kw max source , machine bed 1500x3000 with pipe attachment of 6 metre , this problem is coming from last week, first I ignored it but it was keep arising and now this problem is increased and unable to work properly.
@ClaraChai 10 ай бұрын
It is better to offer me some pictures and videos. @@nannemunnerahihe
@nannemunnerahihe 10 ай бұрын
@@ClaraChai sure,,at where I can send you pictures and videos???
@ClaraChai 10 ай бұрын
@@nannemunnerahihe You can find my contacts in the description.
@anilkhairnar Жыл бұрын
Please tell me move part options
@ClaraChai Жыл бұрын
？
@abhilashkumar2777 2 жыл бұрын
What is duty cycle
@ClaraChai 2 жыл бұрын
Please refer to my CypCut video.
@sharmakuldip2403 2 жыл бұрын
Why am I getting weneness in the cutting in 3mm also 2mm
@sharmakuldip2403 2 жыл бұрын
And how to work peak power ,duty cycle and pulse frequency in piercing & how to use this function
@ClaraChai 2 жыл бұрын
@@sharmakuldip2403 your problem can not fix by a simple answer.
Clara Chai
Рет қаралды 10 М.
Roger Webb
Рет қаралды 60 М.