No video
LightBurn for Galvo Hatching Basics | Cuts and Layers Panel
Рет қаралды 33,729
2 жыл бұрынEverything you need to know about the LightBurn for Galvo Cuts and Layers Panel and Hatching!
The channel, staff, communities, web services... everything. It's all here thanks to the LMA.
► Consider Supporting Us: masters.lasere...
❤️ We're probably earning money when you buy stuff we link. ❤️
✨As Amazon Associates we earn from qualifying purchases.✨
You're going to love this content too!
► Psst... we're on Odysee: odysee.com/$/i...
► FULL LightBurn for Galvo Playlist: • LightBurn for Galvo Cr...
► NEW MakerREMIX Channel! @MakerREMIX
► Laser Everything Linktree: linktr.ee/lase...
► Laser Source Linktree: linktr.ee/lase...
We have SO MANY Laser Resources:
► The 2024 Buying Guide: makearmy.io/sc...
► Join the FREE MakerArmy Network: makearmy.io/
► Join the FREE Matrix Server: rb.gy/m4ca1j
► Join the FREE Discord Server: / discord
► Join the FREE Facebook Group: / lasereverything
► FREE Laser Engraving Starter Settings Packs: lasereverythin...
► Community Fiber Library: db.lasereveryt...
► Community CO2 Library: db.lasereveryt...
► Community UV Library: db.lasereveryt...
► Laser Source Podcast: podcast.lasere...
Listen up! Laser engraving machines are inherently dangerous. The content this channel is for educational purposes only. Laser Everything LLC can not be held liable for any harm caused to any individual or personal property related to settings, activities, procedures, techniques, or practices described in whole or part on this KZfaq channel. By watching this video you agree that you alone are solely responsible for your own safety and property as it pertains to this content. Do your own research before purchasing machines, materials or accessories. LE is viewer supported and probably earns commission when you buy stuff we link.
@anthonyvoight3942 2 жыл бұрын
Alex you're the man, putting out videos faster than I can watch. Just got light burn and again I would be lost without your support. Thank you for all the great content.
@LaserEverything 2 жыл бұрын
I appreciate that! So glad it's helping you Anthony, thanks for watching!
@cocuyona1 2 жыл бұрын
Can't say it enough...Thank you sooo much Alex for this AMAIZING SERIES of videos!!!
@LaserEverything 2 жыл бұрын
You're absolutely most welcome! So glad they're helping you!
@3starsfell 3 ай бұрын
Low key a straight man. But his patron is the only one I sub to
@rarjmag5980 2 жыл бұрын
I'm new to Fiber laser world and your video helps me a lot, I subscribe to Laser master academy to support your channel, thank you soo much for all the good info.
@LaserEverything 2 жыл бұрын
Awesome, thank you! So glad to hear it's helping!
@sedetweiler 4 ай бұрын
This is great! However, how do you know what frequency to use? Is there an explanation of why you are choosing a different value for cleanup vs cutting?
@MelloMC33 5 ай бұрын
Your awesome man... your video's are so much help... I would be completely lost without your video's. Much thanks, I really appreciate you and the work you put into making all these video's. Thank you
@LaserEverything 5 ай бұрын
Just happy to hear they're helping you.
@bel31670 2 жыл бұрын
Once again another AWESOME video... Thank you I leaned a lot...
@LaserEverything 2 жыл бұрын
So nice of you, thanks for watching!
@mariodebnarik5044 4 ай бұрын
Hello my Lightburn dont show black fill on rectangle when i put fill, should i switch on something? Its still only showed like lines. thank you
@computercreationz 2 жыл бұрын
Great stuff! Thank you
@LaserEverything 2 жыл бұрын
Thanks Rob!
@HaydnHamilton 2 жыл бұрын
I love how when your block gets filled the moment you click on FILL ...Mine however stays lines...wonderfull!
@LaserEverything 2 жыл бұрын
You have to turn on "Filled Rendering" in your LightBurn settings. We cover it in this entry: kzfaq.info/get/bejne/jrWknpZos8u4lXk.html
@HaydnHamilton 2 жыл бұрын
@@LaserEverything you are waaaaay to good at this mmmkay...take a break have some tea go to the beach take a day off ! You deserve it....thanx!
@nitinjanglwa Жыл бұрын
What they just called Sub layer, is already there in SCANLAB's software with similarity as "paths".. its cool.
@zina6581 11 ай бұрын
Thank you
@johncrawford9097 8 ай бұрын
How do you turn on the colors on the bottom and dock the layers window
@Dekweekschuur 8 ай бұрын
Nice video again 😀, love the videos very clear explain and whats them all And now this one again because I have a question, i never use ezcad and come from diod and have a mopa M7 jpt now playing with color and have a lib 60W MOPA in 304 stainless steel marked colored. Hatch 0.002 What is that hatch number and where to put it in lightburn because i have more tests with other hatch numbers like 0.001 and 0.004
@MongProduction 9 ай бұрын
amazing content!!
@LaserEverything 9 ай бұрын
Glad you enjoyed
@Dekweekschuur 8 ай бұрын
do they mean the line interval of 0.002 perhaps ?
@merlinunderwood849 Жыл бұрын
Well done ..very informative!
@LaserEverything Жыл бұрын
Glad you enjoyed it!
@thomaslehman1429 Жыл бұрын
Thank you so much, I wonder if you did a video on clean-up, for different metals and their settings. I searched a lot and did not find much. You are the best at this so if you have something please share. Thanks, thomas
@LaserEverything Жыл бұрын
I'll definitely add it to my list Thomas, in the meantime you may get some use out of the bonuses on the LMA - masters.lasereverything.net/
@sirwild 2 жыл бұрын
cant wait for LB 4 galvo to come out
@LaserEverything 2 жыл бұрын
It's exciting!
@CasacutLaser 4 ай бұрын
can we only use 30 layers? how to use more than 30 layers?
@RonaldCremers 2 жыл бұрын
Now in a live stream i asked about fiber/mopa laser and if it was supported. The answer was yes. However i miss the Pulsesettings, do they appear when making the Mopa Profile? Further this is great work.
@LaserEverything 2 жыл бұрын
They do, just have to tick the box in the device settings menu labeled "enable q-pulse width" super easy!
@RonaldCremers 2 жыл бұрын
@@LaserEverything thx for the clear answer.
@iammichaelwalker 2 жыл бұрын
I find that that line out at .02 line interval is way to small for a project, it might take an hour to do a flask for instance, that is not right.. if you do a preview of the time it would take its a long time, not like in EZCADE were .02 and cross hatch takes about 15mins at 200 speed..
@LaserEverything 2 жыл бұрын
I do not believe preview time calcs are currently accurate in lightburn for galvo lasers. Line interval is what it is and shouldn't be affecting the run time between softwares and has not in my experience.
@powershomestead87 Жыл бұрын
So to hatch like we did with ezcad I need to run 2 of the boxes on the upper right corner one cut 45 second cut -45? Kinda confused
@user-ik1rv2ki2m 8 ай бұрын
Why is my frequency limited to 40% to 60% kHz ?
@daxshell242 11 ай бұрын
feature request: on thinner metals, i can get really clean cuts if i give the metal a chance to cool between passes. however, there is no way to tell the program to just chill for 10 seconds between repeats. would be nice so that i dont need to stand by my machine hitting play every 10 seconds for 3 minutes.
@Acutegouttreatment 2 жыл бұрын
LigthBurn runs also on MAC, so is it correct that it is possible to run a Galvo laser via LigthBurn on a MAC computer?
@LaserEverything 2 жыл бұрын
Correct
@boomiedave 2 жыл бұрын
Hey Alex! Great video as usual. I am working my way through the series and I have a question regarding sub layers. Is there a way to apply library presets to a sub layer. It seems to only change the main layer when I apply a preset. I don't know if I am just missing something or it's not a feature. I know I can manually set it up, but it kinda defeats the purpose of having presets in my opinion if i can't apply them to individual sub layers. Maybe I am just doing it wrong....lol :)
@LaserEverything 2 жыл бұрын
Doesn't seem to be, great question. I'll mention it to the LB team, you should too over at forum.lightburnsoftware.com/
@peterlandin457 Жыл бұрын
This dosent work for me. If enable repeat and set it to 10 times, it only does 1 time. I have try it so many times =/
@mindchime Жыл бұрын
I do the "fill" and it doesn't fill. Just stays as outlined box.
@LaserEverything Жыл бұрын
Go into your lightburn settings (not device settings) and check "Filled Rendering". It's filling, it just isn't showing on screen :)
@adamherron Жыл бұрын
Alex, Any idea why when picking fill from the drop down menu, my shape does not show solid on screen? It lasers correctly, but on the screen it still shows as just an outline.
@LaserEverything Жыл бұрын
Yes, easy one, head into lightburn settings and tick the box that says "Filled Rendering" :)
@adamherron Жыл бұрын
@@LaserEverything Thank you! That’s what I get for skipping videos 😄
@LaserEverything Жыл бұрын
Haha no problem here to help. I always encourage everyone to go through the series as if they had never touched a laser. There's lots of little nuggets and easter eggs hidden through out them that often help even experienced laser owners ^_^
@RonaldCremers Жыл бұрын
One tiny question but it can save the world. I got our Galvo working just nicely on Lightburn thanks to your videos. I have only one problem. The working area is not facing towards me but turned 90 degrees to the left. Do you know by chance how to change this? I would be grateful, keep up the good work sir.
@LaserEverything Жыл бұрын
Yep easy, in the device settings (wrench and screwdriver icon) in the very first section labeled "Field" simply change the "Angle" box to your desired angle of rotation and hit okay. Should do the trick.
@RonaldCremers Жыл бұрын
@@LaserEverything as always many thanks :)
@LaserEverything Жыл бұрын
Most welcome!
@learningwithcindy 2 жыл бұрын
What setting are you using for wood, I want to engrave a name in a pencil. to be more specific.
@learningwithcindy 2 жыл бұрын
and I appreciate everything you are doing, thank you
@LaserEverything 2 жыл бұрын
I'd ask for some suggestions in the Discord Server or Facebook Group, links are in the description :) People are usually happy to share.
@YAOG Жыл бұрын
What if I want to run 3 deep engrave passes, then 1 cleanup pass, change the angle, and repeat that 50 times (autorotating the angle each time). How can I get it to keep rotating the angle without repeating cuts I've already done? I can do this in EZcad. In EZcad, you can set the angle rotation, then set the number of times the job will be run and it will continue to autorotate that same amount with each time the job is run. Here, I think I would have to have duplicate shapes and many cuts/layers (1 2 3 deep engrave, 4 cleanup, 5 6 7 deep engrave, 8 cleanup, etc) but there are only 11 layers you can have so that limits that and then before long you're repeating cuts. Thanks.
@LaserEverything Жыл бұрын
Hey Yaog, you can simply enable auto rotate in the hatch menu for the layer, set the passes for that layer to 3, and create a sublayer on the same layer (enable auto rotate on that sublayer as well), and set the passes for that to 1 for cleanup. This can be done with 1 layer + a sublayer within that layer now. You could also save the whole layer's settings to your material library for later use on other projects to not have to rebuild the hatch settings and angle adjustments.
@YAOG Жыл бұрын
@@LaserEverything Yes, but what you're saying to do will have it engrave at x angle, auto rotate, engrave, auto rotate, engrave, auto rotate, and then cleanup. If I run that job 50 times it will go back to the original angle (ezcad would remember to continue the angle rotations where it left off so that you could run the job 1000 times and have a different angle each time). But if I want it to do that 50 times I'd have to set a different angle manually in Lightburn for sublayers 5, 6, and 7 (then cleanup pass sublayers 8). Do you see the issue I'm talking about? I want it to run a job 100 times and auto rotate continuing at the angle it left off on so as not to repeat angles. Ezcad does this. Lightburn does not, unless they changed it recently.
@user-rz6io5sp2m 11 ай бұрын
can you see the hatchlines without having to click preview??
@LaserEverything 11 ай бұрын
Unfortunately no :(
@user-rz6io5sp2m 10 ай бұрын
@@LaserEverything Thanks :)
Laser Livestream - Laser projects & tutorials
Рет қаралды 71 М.
Light Source Engraving - Lasers & More
Рет қаралды 12 М.