LCE EGR Delete 94 4Runner

No video

LCE EGR Delete 94 4Runner

Рет қаралды 10,930

Wesley Moore

Күн бұрын

LCE delete plates installed with resistor to get rid of a check engine light.

Пікірлер: 32

@dhu1042476 3 жыл бұрын

This really is the most simple to understand install with vacum lines and bolts located I have seen so far. I've researched this for at least a year on youtube. Maybe I'll bite the bullet and break out the tools again. Thanks.

@ThisOldYota 3 жыл бұрын

Do it...

@kraptastic333 3 жыл бұрын

hey if you are holding on this because of needing to be more certain, please pm me, i would love to share experience

@gabrielsandoval5873 2 жыл бұрын

@@kraptastic333 hey bro i have a question, my 1995 4runner have all this stuff and is very lazy, a mean when i goin up a hill is like it pullin a trailer 🤣 very lazy, do you think that doing this will get better?

@TheRamziali 3 жыл бұрын

Thanks for the video man best installation or should I say de-installation video on KZfaq!

@leclercj764 3 жыл бұрын

Just ordered mine

@wesleymoore1004 3 жыл бұрын

Awesome! Also comes with a sticker so get excited

@nc1808 2 жыл бұрын

I noticed you kept the AS Reed Valve still on without the stem. Why is that?

@jorgewong910 Жыл бұрын

Did your pickup truck pass inspection after you deleted the EGR?

@texasforever3.025 2 жыл бұрын

So you took the tire off. What about the socket set you used ? I’m having hell w the bolts down low and the one 14 mil at the firewall

@RossWilliamsDC 3 жыл бұрын

How is your truck running now that you have had some time with the delete? I wasn't planning to do a delete until I removed the intake plenum to replace the valve cover gaskets and realized how much better life could be without all that crap in the way. Yet, I still have concerns as some people are saying the delete can hurt the engine over time because you are removing the protection for pre-detonation. There seem to be two camps on it.

@wesleymoore1004 3 жыл бұрын

Truck has been doing great. I haven’t had any issues out of it. Not really any kind of performance gain, just to get it out of the way pretty much. Only had a few months with it and now almost a year without it couldn’t say I don’t notice anything drastic. Overall still runs great

@zapz2101 2 жыл бұрын

@@wesleymoore1004 hello I did the egr delete and the engine runs smoother and I feel the truck running more agile as if I was running with a large load on the truck before egr delete, but now man what a difference, but the only complaint is that I see the truck running with ooor gas mileage. Did you Get the same issue low gas mileage after the egr delete?

@gabrielsandoval5873 2 жыл бұрын

@@zapz2101 hey friend i have a question my 1995 4runner is very lazy, do you think that if i delete this to my truck will run better, with more power?

@zapz2101 2 жыл бұрын

@@gabrielsandoval5873 i would do a full tuneup first, begin with sea foam in the throttle body, gas tank and crank case then run it for a couple of weeks, then do the oil change, oil filter change, air filter change, gas filter and maybe look into the mass air flow sensor adjustment, and only then I would regiment the EGR delete, now I felt a noticeable change in my trucks handling after the EGR delete

@gabrielsandoval5873 2 жыл бұрын

Thank you very much for you suggestion bro 👍✌️ ill do that first to see.

@kevinmiller8265 Жыл бұрын

What is the benefit with this delete ? I have a good idea why i woukd not do this . What effect has it had on fuel trim ?

@JammyCrackcorn Жыл бұрын

Did you remove the air boxes near the air filter housing??

@ethanbisgard619 3 жыл бұрын

I’m doing this egr delete right now actually, and the nut that’s on the very bottom of the tube where you needed a crescent wrench is what I’m having issues with. My AC line is directly in the way of that nut, how did you go around it? If what I said makes any sense. It’s the tube that doesn’t have the ribbed stuff of it, I believe it’s on the bottom of the exhaust manifold. Again, sorry if this doesn’t make sense lol I just woke up and went to work

@wesleymoore1004 3 жыл бұрын

I don’t believe I had an a/c line in the way. The way I filmed it I didn’t move anything out of the way before hand. I’m not exactly sure how to work around an a/c line but you can move it slightly doing your best not to bend it completely. Because there wasn’t a line in the way of mine I’m not 100% sure how to answer. Sorry for the delayed response

@ethanbisgard619 3 жыл бұрын

@@wesleymoore1004 it’s all good ! Thanks anyway. I did end up getting with a wrench so it’s all good! Great video man!

@wesleymoore1004 3 жыл бұрын

Glad you were able to get it done! Thank you