@bighextacy 5 күн бұрын
Idk where you could get more pins to mount the shocks but those shocks look about the same length as the ones for the wltoys k989 1/28 rally/ drift car. They also offer those in aluminum oil filled. However the shocks for the k989 look thinker from your video so that might be an issue with steering angle
@walthersonr.c.3360 2 күн бұрын
@@bighextacy hello and thank you for the comment and for viewing the channel. The WLtoys k989,k969, k979 ,k999 shocks are a little short, but with a little modification, they can work, the oilfield shocks actually leak. I installed the set on my NSX. I had to make a rear bracket for the top rear to mount them. For the price, the LDRC shocks actually fit better.!
@EricHeston98 6 ай бұрын
Thanks for the video, exactly what i was looking for.
@walthersonr.c.3360 5 ай бұрын
Thank you for watching,
@MooseRidez 5 ай бұрын
Big tip, trim a single coil off the front of the shocks. Itll handle alot better. Also after you put in a Aftermarket gyro, if you havent already, slap in a surpass 9g steering servo. Its plug n play and is a ton smoother.
@walthersonr.c.3360 4 ай бұрын
Hello I sorry I just responding, the material is too brittle to try to cut the springs because it’s 3-D print
@pmilitary047 4 ай бұрын
Can you show how to change the wheels. Im having trouble swapping out the front. It feels like its stuck on & ill break it trying to take it off. I managed to slide the rear wheels off just fine. Can you show how its done with out brute force almost breaking it. Please. Thanks.
@walthersonr.c.3360 4 ай бұрын
Hello and thank you for viewing, unfortunately if your vehicle has the plastic hubs in the front, they are hard to remove , you can try to sanding lightly with a 1000 grit sandpaper on each side, or upgrading to the metal hubs they are about 3 / 4 dollars on AliExpress
@pmilitary047 4 ай бұрын
@@walthersonr.c.3360 I finally managed to change them out. By taking off the body and the suspension arm links and leaving the bottom ball joint on to remove the wheels. Yeah they are plastic hex. Thanks. Could do with a metal upgrade.
@pmilitary047 4 ай бұрын
@@walthersonr.c.3360 do you know the exact size of the hex hubs? I could do with upgrading them to metal like the back.
@justaxelrod 2 ай бұрын
How do you remove the suspension pens?
@walthersonr.c.3360 2 ай бұрын
The front pins need to be pushed out from the front of the vehicle to the rear very carefully, the rear pins need to be pushed out from the rear of the car to the front very carefully while holding the mounts! as you start pushing them out, you will notice the pen has a textured in on it!
@justaxelrod 2 ай бұрын
@@walthersonr.c.3360 Hi, thanks for the reply. What tool do I use to remove the pins? If possible would you be able to make a video on how to remove the pens and install the shocks?
@walthersonr.c.3360 2 ай бұрын
You are going to need a small punch or something to push it out enough to grab the rear with pliers!
@erosionreactions 3 ай бұрын
Where did you buy them?
@frankco2972 2 ай бұрын
How you like the car so far just ordered one
@walthersonr.c.3360 2 ай бұрын
Hello, I love the Rx7 , AE86 and the one I had to modify, the gray one, they all run and work very well and it seems like the newer the model the better it is, the passenger right rear suspension on all of the kits is a little goofy Meaning, you’re gonna have to play around and adjust it to get it to work properly but for the amount that they’re charging, you can’t beat it. thank you for viewing my channel and I will try to air a few more videos soon.!
@Ziger_ 6 ай бұрын
How did you manage to pull off the the bars????
@walthersonr.c.3360 5 ай бұрын
Hello , sorry I am just checking your messages, be careful trying to remove the suspension pens !!
@MooseRidez 5 ай бұрын
I used a small allen and pushed it through.
LRC 유피디의거실서킷 YooPD's Living room circuit
Рет қаралды 1 М.
Friendeez
Рет қаралды 17 МЛН
Turning the LDR/C 1802 RX7 into a Pro Drift Car - EP:02 Coilover Shock Suspension and Livery Install
Moose Ridez - Florida Razors
Рет қаралды 5 М.