LE error code lg Washing machine, Not turning jerky washer motor Quick fix

No video

LE error code lg Washing machine, Not turning jerky washer motor Quick fix

Рет қаралды 26,404

how-2-repair.com

Күн бұрын

Пікірлер: 71

@stevequinones6640 Ай бұрын

7/16/2024: I followed your video instructions, and I'm glad to say that your guidance was spot on as the solution worked the first time. You made it a very pleasant experience, and the replacement part was less than $10 to resolve the LE error. Getting the tech here just to to diagnose the issue was going to cost $119. Sweat equity did it. Many thanks for the assist! ✌

@How-to-repair Ай бұрын

Hi thanks a lot for your comment and I'm glad it helped. It would be really helpful for me to get my video shared and help us fight appliance waste! Please remember to subscribe to our channel, as that really helps us 😇 Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/ Thanks, Paul 👍

@latui7350 6 ай бұрын

I so wish you had a branch in the US. Brilliant!

@How-to-repair 6 ай бұрын

To be honest, the way I feel about my country at the moment, I would quite happily move somewhere

@latui7350 6 ай бұрын

@@How-to-repair I feel your sentiment completely. This election year in the US is going to be particularly nasty.

@entasis.fifty-four 5 ай бұрын

Ditto

@mattbandura9015 6 ай бұрын

Good quide for diyers, important if you don't have hall sensor like shown on the video, new versions have it inlegrated with main pcb so you will have to order pcb

@How-to-repair 6 ай бұрын

That is very useful information and I look forward to exploring inside the machine to see how they have constructed this one. Not too sure if the hall sensor should be incorporated into the PCB as that makes it expensive for customers, but it would stop any leakage problems causing damage to the hall sensor.

@paulb9769 6 ай бұрын

Great info but sad that it creates more waste and expense.

@alialajem4680 3 ай бұрын

Mine is jerking but not spinning. When I open the stator, there was no hall sensor there. I watched one of the videos on KZfaq where the technician mentioned that there are some versions of this LG washing machine without hall sensor. It is integrated within the board, then the question here how to fix it

@mattbandura9015 3 ай бұрын

@@alialajem4680 replace the board

@Fastandpro 6 ай бұрын

Being a top loader we replaced dozens of hall sensors and motors on F&P machines due to water damage mainly after bearing failures. Luckily we also had machines with computer failures to salvage good motors from.

@How-to-repair 6 ай бұрын

That's the great advantage of being in the trade. We've always got the lock up full of spares from old machines. The problem is I'm starting to look like a very big hoarder

@laurencelac9486 2 күн бұрын

VERY CLEAR THANKS

@How-to-repair 2 күн бұрын

Glad it helped! I would love your input on our pole as you enjoyed the video and hopefully got your machine working again. Please give your opinion on this. kzfaq.infoUgkx1CErYWp7q7DXV83jC3EEmoJ1C_dmWIG6

@debimj4968 3 ай бұрын

Thanks for the video. We were able to order the sensor for our Kenmore and fix it because of your video. Great video and very informative.

@How-to-repair 3 ай бұрын

Really glad you managed to get your washer up and running again. I take it to you in the US as you ordered from Kenmore. What would really help me to get my video seen as I'm no IT expert is to either share the channel or at least post it to your friends my videos might not be KZfaq superstars, but they save Appliances from the scrapheap. Share and help us fight appliance waste! @debimj4968 please remember to subscribe to our channel as that really helps us kzfaq.infoe432SAb2g08 Thanks, Paul 👍

@debimj4968 3 ай бұрын

@@How-to-repair Will do. I tried to get the part through your link, but was unable. Yes I am in the USA.

@How-to-repair 3 ай бұрын

@@debimj4968 the most important thing is, you've got the machine working and because I'm in the UK we would not have been able to ship to you anyway but really glad everything is up and running

@aesthetify 4 ай бұрын

superb video - think it's fixed ours too (no faults for 9 1/2 years until Hall sensor).

@How-to-repair 4 ай бұрын

Really glad the video assisted you replacing the sensor may I ask a favour? What would really help me to get my video seen as I'm no IT expert is to either share the channel or at least post it to your friends my videos might not be KZfaq superstars, but they save Appliances from the scrapheap. Share and help us fight appliance waste! @aesthetify please remember to subscribe to our channel as that really helps us kzfaq.infoe432SAb2g08 Thanks, Paul 👍

@ahoorapersia4698 6 ай бұрын

Thank you sir 🙏🏻👍⚘️

@How-to-repair 6 ай бұрын

Glad you enjoyed it. There will be a full playlist of all LG washing machine tutorials. kzfaq.info/sun/PLnAHZbSarsyHLR4x9XPIS-ZEsheufxm9Y @ahoorapersia4698 please remember to subscribe to our channel as that really helps us kzfaq.infoe432SAb2g08 Thanks, Paul 👍

@chhumsaren 8 күн бұрын

Thank you so much 👍🏿

@How-to-repair 8 күн бұрын

You are very welcome mate, please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

@SeanCarlson-r9l Ай бұрын

Thank you!!! This was a great help.

@How-to-repair Ай бұрын

@vaclavkovar470 2 ай бұрын

I replaced Hall sensor but my LG wd 10396nd didn ´t work..but I have to say, I´ve learnt something new

@s.8020 13 күн бұрын

Thank you so much sir...🎉🎉🎉🎉

@How-to-repair 13 күн бұрын

@TheWangbolizhong 6 ай бұрын

👍👍

@How-to-repair 6 ай бұрын

We've just had the latest machine coming from LG, and there will be a full playlist on all repair tutorials on these LG washing machines kzfaq.info/sun/PLnAHZbSarsyHLR4x9XPIS-ZEsheufxm9Y

@mariomhlanga1968 3 ай бұрын

Thanks for your help ❤

@How-to-repair 3 ай бұрын

You're welcome 😊 @mariomhlanga1968 please remember to subscribe to our channel as that really helps us kzfaq.infoe432SAb2g08 Thanks, Paul 👍

@VM-ku5il 3 ай бұрын

Much appreciated 👍🌹

@How-to-repair 3 ай бұрын

Hi @VM-ku5il thanks a lot for your comment. It would be really helpful for me to get my video seen, as I'm no IT expert, to either share the channel or at least post it to your friends. My videos might not be KZfaq superstars, but they save Appliances from the scrapheap. Share and help us fight appliance waste! Please remember to subscribe to our channel, as that really helps us 😇 Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/ Thanks 👍

@michealcotterill170 5 ай бұрын

Thanks 👍

@How-to-repair 5 ай бұрын

Glad this helped you. I hope you got your motor or hall sensor fixed. As an ageing appliance engineer, my expertise lies more in the domain of domestic devices than in IT, resulting in a limited understanding of KZfaq video optimisation. Consequently, my videos might not reach their full potential due to these IT constraints. Nevertheless, they offer invaluable aid to those who encounter them. Your support in sharing our channel on social media would be immensely valued. By disseminating our content, you enhance our visibility and contribute towards addressing the pressing matter of appliance wastage. In turn, you play a role in averting numerous machines from facing an untimely end in the heavenly scrapheap of appliances. Thanks 👍 Wrinkly hands fix appliances, not algorithms! My videos might not be KZfaq superstars, but they save Appliances from the scrapheap. Share and help us fight appliance waste! @michealcotterill170 please remember to subscribe to our channel as that really helps us kzfaq.infoe432SAb2g08 Thanks, Paul 👍

@jacktan1576 Ай бұрын

Hi, my motor can’t even spin by hand, how do I check if any objects is stuck in between drum and motor as mentioned by you? Managed to opened and removed the hall sensor but now think that might not be the source of the problem. Thanks in advance.

@therealrollaz 5 ай бұрын

do you know what the ohm readings SHOULD be on the hall sensor and on which pins to verify it's bad with an ohm check?

@How-to-repair 5 ай бұрын

The manufacturers do not give me the readings you can only obtain the information that I actually put in the video

@sunilpanagatte657 2 ай бұрын

Use full

@ansariosman204 3 ай бұрын

How do i set a diagnosis for a washer & dryer combo wd-1256rd

@How-to-repair 3 ай бұрын

Hi @ansariosman204 I will need the full model number of the identification plate and the details of your problem. Please use our contact us page and make sure you fill out the request for what your problem is. We will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks 👍

@indesitlghotpointwashingma8305 5 ай бұрын

Can that see through model be plumbed in?

@How-to-repair 5 ай бұрын

@monkimo 5 ай бұрын

I changed the hall sensor no more LE code but it doesn’t reach full spinning speed not even a 400 rpm

@How-to-repair 5 ай бұрын

That's a new one try going into diagnostic mode and following the procedure as in the video make sure the drum is empty

@me-days 26 күн бұрын

I opened the motor and I cannot see the hall sensor in my WDC1215HSVE

@How-to-repair 26 күн бұрын

Hi, I will need the full model number of the identification plate and the details of your problem. Please use our contact us page and make sure you fill out the request for what your problem is. A video shoot of the problem would be perfect as well. I will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

@RobertP7884 5 ай бұрын

I have LG direct drive washing machine with damaged tube (front) and collapsed drum , where can i find part number for drum+tube kit? Washing machine model F14B8QDA

@How-to-repair 5 ай бұрын

As there are multiple variations of this machine, I'm giving you this link so you can put in your full model number repairpartsteam.co.uk/search?g7=3083356N&suchbg=F14B8QDA&rpt=b5846a951b

@RobertP7884 5 ай бұрын

@@How-to-repairthx found exact mine as LG F14B8QDA F14B8QDWA.ABWQEUK - is part number on the tube and on the drum somewhere?

@SaidSadawi-e5z 7 күн бұрын

مرحبا..هناك محركات في lg بدون مستشعر قاع فهل يكون الاصلاح بالكارت في هذا العطل؟؟؟

@How-to-repair 7 күн бұрын

Hi mate, if you are talking about the hall sensor then sometimes these are built-in to the card units we normally just replace the pcb.

@SaidSadawi-e5z 7 күн бұрын

@@How-to-repair أشكرك على الرد ❤️👍٠لكن ماوجدت احد يصنع فيديو لإصلاح هذا الرمز lE في الأجهزة المدمجة.فهل يتم اصلاح لوحة التحكم في دائرة المحرك؟؟

@tutzidoodles-v9q 29 күн бұрын

minecdont have hallnsensor but it show LE error how to fix it.can you help me

@How-to-repair 29 күн бұрын

Hi, I will need the full model number of the identification plate and the details of your problem. Please use our contact us page and make sure you fill out the request for what your problem is. A video shoot of the problem would be perfect as well. We will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

@andrewhogarth6799 5 ай бұрын

I’m sure I’ve mentioned before…love the videos n help …but….the absence of “gloves” ..they has some some sharp edges on the casings etc….please..wear gloves pal…

@stevensmith3308 23 күн бұрын

$16 Amazon, all fixed

@azzedinemghachou 2 ай бұрын

Bonjour je possède un lave linge lg F52590WH 15kg,quand je lance un programme rapide et le tambour ce bloque à la 24 ème minutes ou à d'autres moment du lavage et du rinçage du temps restant,quand j'ai cette erreur,j'ouvre le hublot et je tourne le hublot manuellement. après je referme le hublot et la machine fonctionne très bien,j'ai déjà changé le rotor,le Stator,la tachimetrie,le bandeau de commande avec sélection des programme,j'ai toujours cette panne qui affiche de temps en temps un code défaut LE,je pense que ces la carte de puissance qui déconne.cordialement

@How-to-repair 2 ай бұрын

Si le moteur a été testé et que vous avez déjà remplacé le capteur à effet Hall, il s'agit probablement d'un problème au niveau de la carte de circuit imprimé. Si la carte de circuit imprimé n'est plus disponible, la meilleure solution est d'en trouver une d'occasion sur des sites d'achat comme eBay. Comme vous êtes en France, je ne sais pas quels sont les sites que vous utilisez là-bas. Vous pouvez essayer de lancer un cycle de test sur votre machine, mais en général, le code d'erreur LE indique un défaut lié au moteur. Vérifiez également la continuité de chaque fil allant de la carte de circuit imprimé au moteur. Parfois, les fils situés au bas de la machine peuvent souffrir de la fatigue du métal et se rompre en interne. Il est donc utile de les inspecter également. Si vous avez besoin de pièces détachées pour cette machine, consultez le lien suivant : www.how-to-repair.com/ Utilisez le numéro de modèle complet et, parfois, le numéro d'identification figurant sur l'étiquette d'identification. Merci, Paul 👍

@azzedinemghachou 2 ай бұрын

@@How-to-repair bonjour monsieur,merci beaucoup d'avoir pris le temps de répondre à ma question,j'ai changé le capteur effet hall (tachimetrie) plusieurs fois,j'ai aussi acheté d'occasion un bandeau de commande avec programmateur,j'ai acheté d'occasion un Rotor et stator pour tout tester et le problème reste le même,la machine fonctionne bien mais le tambour ce bloque à plusieurs intervalle dans le cycle du décompte du temps restant du lavage,je pense acheté une machine neuve samsung 18kg,je serai tranquille,si je change la carte électronique de puissance et que j'ai encore des problème,j'aurais dépenser de l'argent pour rien,le mieux ces d'acheter du neuf.merci à vous

@azzedinemghachou 2 ай бұрын

@@How-to-repair et si les câbles aurait un soucis à un endroit la machine ne fonctionnerait pas bien alors que moi elle fonctionne très bien,ces juste des blocage de tambour de temps en temps

@elfiwolfe 3 ай бұрын

:( and I get this 2 weeks after replacing a washer. If I had this back then it would have been better. Oh well.

@melbournekajengo6300 Ай бұрын

I have a problem with my LG it's a new model lg it doesn't have a hall sensor but it's showing LE error code, what should I do since the model doesn't have sensors pliz?

@How-to-repair Ай бұрын

Hi, I will need the full model number of the identification plate and the details of your problem. Please use our contact us page and make sure you fill out the request for what your problem is. A video shoot of the problem would be perfect as well. We will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍

@Imake_edits12345 Ай бұрын

Hi sir. Plz share your number. I need guidance for my LG front load 8 kg DD motor and haul senor. Best regards from Pakistan 🇵🇰

@How-to-repair Ай бұрын

Hi, I will need the full model number of the identification plate and the details of your problem. Please use our contact us page and make sure you fill out the request for what your problem is. A video shoot of the problem would be perfect as well. We will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/ Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍