Learn an alternate method in creating ribs between rounded edges in Fusion 360

Learn an alternate method in creating ribs between rounded edges in Fusion 360 | Rep no. 10

Рет қаралды 2,190

Жыл бұрын

In this exercise we use an alternate method to add a dynamic rib between two rounded edges in Autodesk Fusion 360. While this approach may not always be practical, it can prove useful in special use cases where you may want the rib to conform to the shape of the edges.
🔥🔥If you have found this video useful and would like to support me, you can buy me a coffee at
www.buymeacoffee.com/CADjungle
These exercises are intended to help you become familiar with Autodesk Fusion 360 through repetition. These models are not always exact but, are measured for approximation. When attempting to reproduce models for 3D printing, be sure to verify your own real world measurements for authenticity.
If you enjoy this content, please like and subscribe for more upcoming and progressive videos.
I do not work for Autodesk and currently do not get paid to promote their software.
This channel is independent of Autodesk, Inc., and is not authorized by, endorsed by, sponsored by, affiliated with, or otherwise approved by Autodesk, Inc

Пікірлер: 19

@craignevels3530 21 күн бұрын

excellent

@dmanton300 Жыл бұрын

That split face rib was excellent, thank you!

@CADJungle Жыл бұрын

I'm glad you liked it!

@loubano Жыл бұрын

Very smart idea to use split tool. I did not understood till I saw the result 😁👍 Thanks a lot 😁

@CADJungle Жыл бұрын

Glad you liked it!

@BarryBernau Жыл бұрын

Great tutorial! CAD Jungle is the best!

@CADJungle Жыл бұрын

Thanks for the support, much appreciated!

@tqdam Жыл бұрын

Excellent tutorial. I always learn something new watching your lessons. Keep it up!

@CADJungle Жыл бұрын

I'm glad it helped!

@colinedwards1163 10 ай бұрын

Very nicely presented thank you👍

@CADJungle 10 ай бұрын

Most welcome 😊

@billkellogg1403 Жыл бұрын

I saw the last “rib-by-loft” lesson too. So, what if the drawing called for the top of the rib to be flat? This is really concerning to me. Thanks!

@CADJungle Жыл бұрын

You can always stick with the original rib command so it will remain flat. However, keep in mind, that to make the rib conform to your specifications, you will need to play with the sketch line and move it slightly away from the corners to insure it touches both lips of the rounded edges. If not, you will end up with one side being at the top of the rounded edge while the other side slightly below the top edge. In this exercise its simply to avoid the flat edges created on the corners when creating ribs. This is demonstrated in this video as well. kzfaq.info/get/bejne/d6yfi8hyqZyxcYU.html

@bertveldhuizen8699 Жыл бұрын

Making that rib, could you just draw a triangle instead of just the diagonal line, extrude it to the width you want, and then extrude the edges to both cylindrical objects?

@CADJungle Жыл бұрын

Yes you could however, you will run into the issue of the rib not conforming to the shape of both rounded edges. You will have flat edges instead that may protrude a bit. Ribs more commonly are connected slightly below the actual edges. Although this method I presented isn't a common practice, this was just a demonstration on how to achieve a rib from edge to edge if it was something that anyone wanted to try.

@JBCool0729 Жыл бұрын

Good Idea but not for production. So actually its useless..

@CADJungle Жыл бұрын

While a different approach is a good idea in some instances, it may not be practical in all use cases, but it is definitely not useless.

@JBCool0729 Жыл бұрын

@@CADJungle Yes it is. Most of the time design are made for production or prototype. This is just for looks. So yes it is useless in production.

@CADJungle Жыл бұрын

While I would agree with you about its purpose, again it depends on what you are producing. Yes ribs and gussets for that matter serve specific purposes and have best practices associated with them. If you are working in an industrial shop or injection molding industry that has specific requirements and tolerances, then yes. While the term "useless" is a broad statement, it doesn't apply in all cases.