Learn how to test bridge rectifier using the multimeter

No video

Learn how to test bridge rectifier using the multimeter

Рет қаралды 22,262

Electronics Repair Basics_ERB

Күн бұрын

You going to learn how to test the bridge rectifiers using the multimeter.
My Website:
www.prospace20...

Пікірлер: 32

@borujawi5629 Жыл бұрын

i have seen different videos' in KZfaq,videos that done by different professionals ,but No one is explain like you, thank you so much i have seen your videos that you have launched on you tube, all videos were so crucial/core or very important to professionals, so continues line this...

@electronicsrepairbasics_erb 11 ай бұрын

Wow, thank you!

@jonathanmonger111 Жыл бұрын

Your presentation is extremely helpful. Thanks

@electronicsrepairbasics_erb Жыл бұрын

Glad it was helpful!

@jonathanmonger111 Жыл бұрын

Best video ever

@ronin99999 Жыл бұрын

Very helpful thank you

@electronicsrepairbasics_erb Жыл бұрын

Glad it was helpful!

@dzabakwesi2213 9 ай бұрын

Thanks for the knowledge. But please sir can you do a video on how to test the smd bridge rectifier used in mobile chargers?

@xhulilleshi Жыл бұрын

thanks ❤❤

@electronicsrepairbasics_erb Жыл бұрын

You're welcome 😊

@ahmednor5806 Жыл бұрын

🙏🙏🌹🌹Thanks

@electronicsrepairbasics_erb Жыл бұрын

You’re welcome 😊

@Luke-12V 2 жыл бұрын

Thanx all video 🥰🥰

@electronicsrepairbasics_erb 2 жыл бұрын

Thank you too

@rosliks7647 Жыл бұрын

When tested diode onboard I got reading +563 but upon changing ends it read +1350. It only occured on 3 diodes closely onboard induction cooker but other diodes seem perfectly ok. Is the diodes ok or other component onboard are at fault.

@electronicsrepairbasics_erb Жыл бұрын

Its Ok

@rosliks7647 Жыл бұрын

@@electronicsrepairbasics_erb Thank you.

@akdiscreto 5 ай бұрын

Hello, when I measure between + and - (reverse polarity) I do not have a double voltage drop ( 1 V) but 0.5 V only. Could it be the reason for the PC monitor not working?

@electronicsrepairbasics_erb 5 ай бұрын

Yes Bro it could be

@Music-Gear 4 ай бұрын

When testing a 4 pin bridge rectifier, should i get a beep in continuity mode when only testing the two midlde pins ~ ?

@electronicsrepairbasics_erb 4 ай бұрын

No, no beep bro, any beep means failed

@Music-Gear 4 ай бұрын

@@electronicsrepairbasics_erbOk, I should have mentioned I am testing it on a circuit board. I have test another one on the board and when I put the black and red prongs on the middle pins~ it also beeps.

@nickloss2377 Жыл бұрын

are you lowering the pitch of your voice in post processing? either that or there's something wrong with your mic..jeez ..sounds like an electronics tutorial from the underworld

@emilhrenka1611 Жыл бұрын

if i dont get double rating but get exact same does that mean its bad?

@electronicsrepairbasics_erb Жыл бұрын

Hi Emil, No, the only case that we can say that the bridge is failed is when you get a continuity ( buzzer ).

@emilhrenka1611 Жыл бұрын

Oh thank you for your response

@kironsk7697 Жыл бұрын

Exactly I'm not getting double reading from one end to another end and rest of the things are matching with your explanation. Then is this bridge rectifier defective?

@kilgoretrout4461 Жыл бұрын

@@kironsk7697that’s exactly what I’m getting. Good numbers except no double reading on the end.

@kilgoretrout4461 Жыл бұрын

Oh, and yea, I’m getting continuity, so it’s bad. Thanks