I have the Roxi 3 and it has quickly become one of my favorites. I can't put it down. I just sit and fidget with it all the time. Absolutely a great knife.

Can't wait for Knife Center to send me mine.

"Next week on WhatIfEDC, Kev attempts to swap Skiffs for another set of Skiffs."

You should Test the mini Buster and the sugga

Cool vid Kevin, this one is awesome liking the whole disassembly vid in general and the process of you finding the right feel for your knife. This is definately a home run for We this time around. Keep making sharp things fun and enjoyable

I got the same problem

Honestly i love mine being the black version i think it looks sweet with the bronze hardware and the action is great detent is good blade shape is fire!! great video brother..

Intro looks so good dude! Still kicking myself for not buying a Roxi 3 at BSW. Didn't realize they hadn't dropped yet

Love my Roxi 3 TS my no flipper large Sheepdog is running backup now.

Great video Lefty. I was wondering how you would compare this to the high fin? I was thinking about getting one of them. Thank you👍

I saw a review where the guy said the finish felt rough and dings easily. He showed some very obvious silver areas. I love the design and look of the knife but debating the plain titanium handle instead.

Bought the all black version after watching your unboxing, this thing's awesome.

I really like their designs. This is a cool little knife. Great video 👍

Goddamnit….I have a knife problem. 🤦🏻‍♂️ I just ordered this knife…while I wait for my WinterBlade Factor batch 2 to come in. UGHHHHH

I went looking for it like a week ago. I’m on an email list so we’ll see how that goes. Thanks Lefty!

Hey Kev, Good review. Love my Roxie 3… but the factory edge on mine was trash. Nasty. Still had a burr on it. Uneven grind towards the handle. Fixed it myself with now a nice mirror edge, but for $200+ WE needs to do a better factory edge. Not a fan of the stone wash blade finish WE uses either.

The 4 inch version is a much better knife with better balance. The estrogen in those craft beers is activating your recently bias. Need to layoff that stuff.

I don't like to be critical and I think he's getting better but I think Joe has nicked a couple of your choils unless it was from factory. A couple of the ones you've shown look to have a little stone or belt mark. The 5.5 in this case.

Unfortunate for you, but every single WE Knife I've got has been absolutely perfect in every way. I've had way less luck with my Microtechs. In fact, I've sold all of my manual Microtech knives because their of their detents.

Where can one get a cool leather work mat like that?

Can I fix a weak detent? I have a vosteed thunderbird that closes way to easy. Just bought the WE Roxi 3 on WMK lol.

I can see people complaining that it doesn't have a sharpening choil, doesn't bother me though. I like the finger choil unlike the F5.5 that digs into my finger next to the sharpened edge, most of them do and I wish makers would get away from that annoying feature, it also takes away from the total sharpened edge of the blade, that bugs me too. I really like the knife overall but..... The elephant size warnsheepcliff blade is basically useless in my EDC needs. I need something with a point and a slight belly at least. It's a sweet looking knife for sure.

Is the nymble w 100 bucks better?

What size are the bearings for this(inner and outer diameter of the cage)? So I can buy some before I buy the knife :D. Thanks

To tighten properly hold the knife upside down, blade open, push the lockbar back and make sure the blade moves freely upwards, tighten till it gets a little stiff and back off slightly making sure it moves freely again. That's right where it should be. I find Frog Lube to be the best for the detent ball, it doesn't run and get on the tang of the blade, it's all natural, and a protective paste against rust. The whole swapping of bearings I don't get, but whatever, being ceramic is what matters, steel rusts, aftermarket bearings will change the action if they are the slightest bit thicker than the original, sometimes even a washer being a minuscule thicker than the other will throw off centering? A company like WE has done the engineering, you never tried the originals bearings again?