Hi C. P., welcome to my channel and thank you for your kind words, greatly appreciated it and all the very best with your build too. 😉

Hi Nox, welcome back and thank you for your feedback, greatly appreciated it. Enjoy the content 😁

Hi Deviant Builds, welcome to my channel. Thank you for your valuable feedback, greatly appreciated it 😉. All the best with your build too. 👍

Hello Константин Кудряшов, welcome to my channel, I am glad you find this content useful. All the best with your build too. 😉

HI smokes lottapot, welcome to my channel and you are most welcome. All the best with your son's build too. 😉

HI HARDwithSTYLE, welcome to my channel and thank you for your compliement, greatly appreciated it 😉

Hi Bikaz, welcome to my channel and thank you for your kind words. Greatly appreciate it. 😉 all the best with your build too . 👍

HI @truckingpix, welcome to my channel and thank you for your valuable feedback. All the best with your build too.

Hello PZ, welcome to my channel. Glad that this content did aid you. Thank you for your feedback and all the best with your build.

Hi Ji Mi, welcome back. All the best with your build and do share with us your experience after you’ve did up your build too 😉👍

Hi Darkldrees, welcome to my channel. I am glad you find this useful. Thank you for your feedback and all the best with your build too 😉

@KleoYan thank you man I'm about to order the galahad II 240 for my build

@@DarkIdrees all the very best and thank you for the updates 👍

hi Jun G., welcome to my channel and thank you for your valuable feedback.

Hi Shinano, welcome to my channel. Thank you for the follow and I am glad you find this content useful. All the very best on your build too. 😉

Hi C0mBaT_M0nKeY, welcome to my channel. Thank you for your feedback, greatly appreciated it.

Hi Wayne Hughes, it's good to see you and yup I too feel the cables could be better. Thanks for the feedback buddy 😉

Hi Асет Каратаев, welcome to my channel. Am glad you like my content 😉

Hi TreyJays, welcome to my channe and thank you for your kind words. All the best with your build too 😉

Hi David Jeffries, welcome to my channel and thank you for your feedback. I am going to do up another content regarding about the performance, but that will take sometime as I am taking my time to run the liquid AIO each for a full one week.

Hi Naudy Caudy, welcome to my channel. That's good, happy for you and all the best with your build too 😉

Hi Nico, welcome back buddy and thank your feedback ☺️

Hi Arctic, welcome back and nice of you to drop by. Thank you for your valuable feedback 😉

Hi Maximiliano Helfmann, welcome to my channel and thank you for your feedback. All the best with your build too! 😉

hi Matcha Mate, welcome to my channel. Greatly appreciated your feedback and to have shared your experience too. Thank you! 👍

@@KleoYan pls upload thermal test video we are waiting

@@shivang0017 hi, do allow me to have a little more time. Am still testing it and additional to this, there is another new AIO coming from Lian Li too. stay tune and thank you.

Hi John Chan, welcome to my channel, thanks for pointing out. yup I notice on the specs. I miss that out as i was measuring it (eyeballing with a measuring tape) thanks again, greatly appreciated it.

@@KleoYan I'm definitely looking into getting the performance version. The angled tubes off the radiator is exactly what I'm looking for. I just happen to have the AP201 case!

@@johnc0817 that’s good. I am sure you will get to enjoy mounting it and of the thermal results. Cables are not as messy as the GA II Trinity SL-INF. All the best with your build too.

Hi Rebs Rebolledo, welcome to my channel. Yup, in gerneral, all plug and socket will glide into place without too much force. thank you for your emphasis 😉

Hi Lith, welcome to my channel, that will be on another view, will take sometime though but thank you for the suggestion. 😉

​@@KleoYanwaiting for this as well!

@@xxVanos Hi welcome to my channel, as mentioned, will take some time and thank you to have visit my channel.

Hi Shzaki, welcome to my channel and thank you for your feedback. All the best with your build too.

Hi TheChaosilator, welcome to my channel. Yup, you are correct, which is now, I am going to use these cooler each for a week, then do a benchmark before I change to another cooler. This way is not just grab and show stats. let it run for a week then to show results.

Hi 1TGF43T1TGFFGT143TR UEFHROWHEF0931434, welcome to my channel. thank you for your input, but the price for me is not that decent. It's expensive in Singapore due to the import tax.

Hi Quang Tran, welcome to my channel and thank you for the enouragement 😉

Hi DennisR90, welcome to my channel. This will take sometime as I will be comparing with some other AIOs. Once again thank you for visiting. 😉

Hi [NLB] Sun Wolf, welcome to my channel. I did try placing to the VRM side, both workable, it's just that this is my personal preference as your VRM heatsink will have more heat compared to the rams area, this is why i advise to place it towards the ram side. Nevertheless it will work on either side. so long the hose is not pointing downwards. As for the Offset of the AMD vs the coldplate. you are right, it is indeed not align but the flow of the slit inside the coldpate cools better with the orientation I have suggested. You can test it as that's my experience with it. Thanks for visting and all the very best with your build too. 😉

Hi Skanda Thalya Shankarananda, welcome to my channel. I will see what I can do. Thank you for the suggestion.

Hi Invalid English, welcome to my channel. If you are using the GA II Trinity 360, you will need to have the SL-Inf fan controller for your other fans to work in L-Connect 3.

Hi 3_Kids_One_ Shot, welcome to my channel. I wish for the 280 too. maybe send your comments at lian li's reddit forum. The do listen and read viewers feedback. www.reddit.com/r/lianli/

Hello Tanmay, welcome to my channel and am glad that this content did aid you. All the best with your build toon😉

​@@KleoYan I have new GA II trininty INfininty AIO+ 2 set of Lian li fans+2 Strimer I have only 2 usb hub,,cant connect all controllers. If I connect (argb sync cable) the strimer controller AND my pump head argb to the 2 SYNC connections in the FAN controller AND use the FLAT cable in AIO FANS so I can use only 1 controller. will this work? In this case I have to connect 1 USB header of the controller which will have fans +strimmer+PUMP ARGB and another USB header I will use for the AIO PUMP. will this work SIR?

​@@lostyraulto answer your questions. It does not work that way. I would advise you to get a internal hub from NXZT. You might want to watch this to understand how they work kzfaq.info/get/bejne/ec2mqLh3yszKaIk.html

Hi Michael Paris, welcome to my channel. I see what I can do, thank you for your suggestion.

Hi cluz, welcome to my channel. Do pardon me, I am not able to understand your sentences. 1st which AIO cables to the motherboard and what do you mean by on the sl in and not the control box.. I am confuse.

Hi foxtrotbravo, welcome to my channel. Yes I do notice that. If you look carefully on the screws where the bolt goes at four corners. The thread on the screws are not threaded fully. That’s where it stops the bolts from over tightening. That’s how it supposed to to work. The suspended cross bar act as a retention to hold the coldplate to the IHS, that’s why the four rubber studs that is holding the backplate does not flush.

Hello ReflexionCostik, welcome to my channel. Yup my tongue got twisted at times 😂 thank you for your valuable feedback 😉

Hi Juan Shaft Patel, welcome to my channel. Yup, it was posted at their Reddit forum. Thank you for your information.

Hi Genadi 'Enomir' Georgiev, welcome to my channel, I will advise you to have a replacement. if you did the refill yourself, the warranty will be void. lian-li.com/contact-us/

hi Shivang001, do allow me to have a little more time. Am still testing it and additional to this, there is another new AIO coming from Lian Li too. stay tune and thank you.

Hi aurorate, welcome to my channel. I believe you are using the GA II Trinity. As what you've mentioned. Yes you can leave it as it is, but you will need to use your motherboard UEFI or application to control the RPM of your radiator fans. As for the ARGB, that's correct, plug to the uni controller and make use of the L-Connect 3 app to control the argb effects.

Hi Osar deGozar , welcome to my channel. Thank you for your valuable feedback. I do agree with you as noise is subjective to individual sensitivity. As for the pump to run at PWM. I have witness more cases on pump failure in the past. This is due to the inconsistency of the pump impeller. Maybe newer generation will not be affected but at all times I practice to use a flat rpm. Again thank you for your valuable feedback.

Hi Julie Fisher, welcome back. Yes infact they are getting better but just that end users like to mix argb ego system which causes issues. As for the cables, I will hightlight this to Lian Li, hopefully the next version will be with better cabling.

@@KleoYan Yes, I had already written my comments, and then you actually raised some of the same issues at the end of the video. So we are both seeing the same problems/opportunities for improvement, to make Lian Li the very best.

@@Jules_Diplopia thanks Julie Fisher, greatly appreciate this. for the moment am consolidating all feedbacks and comments from here and via email, then I will again bring this up to Lian Li.

Hi Nucl3ar, welcome to my channel. Yes you can run the radiator fans directly from the motherboard fan header (CPU_FAN1) and plug the argb to your uni fan controller. This is recommended, just incase if the uni controller malfunction. In the event of malfunction, at least you know that your radiator fans are still up and running. Only the argb effects will not work. As for case fans, you can just run directly from the uni controller.

Hi Strange Weird and Funny, welcome to my channel. I am still trying to figure out what you are saying. so sorry I don't understand what you mean, mind to eleborate, thank you!

Hi 1SaG, welcome to my channel. It depends which GA II Trinity you are using. if you are using original, the connection is pretty straight forward, what will add more to the equation will be the GA II Trinity Inf, as you will need to fiddle which two controllers. one from the block and other is the SL Inf fans. as for all connection to Liquid AIO, I always do this. plug the radiator fans directly to motherboard CPU_FAN and to use motherboard UEFI to set the fans. As for the argb I will use the controller to us L-Connect 3 app to do the effects.

@@KleoYanThanks for responding! To clarify: It is the basic Trinity 360 (Performance version seems to have dropped off the market and INF version is out of stock everywhere over here.. :) ). Meaning I don't have a Lian Li RGB controller and would either have to use L-Connect or my board for RGB. I tried my case's built-in RGB-controller yesterday for the rest of my RGB-stuff and it seems to be a bit limited in its capabilities, so I'm not going to use that one. I ended up running everything through L-Connect and while it does work, fan control is a bit too "hectic" for my taste, with the AiO-fans ramping up/down too often under light to medium loads whenever the CPU gets just a *little* warmer. A more "relaxed" custom curve should help here, I guess. Temperatures under heavy loads (Cinebench, etc) are quite amazing compared to the gen 1 Galahad 240 I used before with the i7-14700KF - so the AIO is doing its job. I went by the manual (I hope) and plugged the fans' PWM and RBG-connectors into the adapter cable that then connects to the pump. The pump's fixed cables are plugged into SATA-power, a USB 2.0 header and the "CPU Fan" header. The slightly annoying thing about that method is that I can't monitor the fans' RPM anywhere except in L-Connect. The motherboard only sees the pump's RPM, which it lists as "CPU" - I guess because I plugged the fixed PWM cable into my "CPU Fan"- and not into my "CPU Pump"-header. I do feel slightly uncomfortable letting an app control my CPU fans, so I would prefer running fan RPM and perhaps pump-RPM through the board. Can I still use L-Connect to control RGB when I do this, or should I rather ditch L-Connect completely and run everything (fan-RPM, pump-RPM, RGB) through my board? It is an MSI Z690 Tomahawk which does have three 5V RGB headers, so I should be fine WRT connections. Also: If I decide to go through the motherboard, do I still need to plug the SATA and USB cables in or will the AiO get powered through the fan-headers like that?

@@1SaG hi Welcome back. as why your motherboard does not read the PWM readings, that because you are connected to the pump controller which you will see in L-Connect 3, what you can do is.. between the cable O and N, at the O end, plug the 4pin pwm to your CPU_FAN header and the argb connect from cable O to N. This will let you see the PWM status on your motherboard but you will need to make use of the UEFI or motherboard utlity to control the fan curve. On my other content, I did it this way for the radiator fans as I prefer to have the motherboard to take control. In the event if the controller of the pump fails, only the argb is affected and not the radiator fans which runs off directly from my motherboard.

Hi kydns, welcome to my channel, after looking at the layout, you got no choice but to place the pump tube downwards which interm there will be increase of thermal.

Hi Robertorgg, welcome to my channel. for your Galahad Trinity SL Inf, you do not need to plug the argb cable from your pump to your motherboard 5v 3pin argb header. make use of the L-Connect 3 app to control the radiator fans and pump argb. as for your reverse fans, as for your reverse fans, I am not sure how the package is like as I do not owe any, but for your GPU strimer plus, you can plug directly to your motherboard ARGB header. Kindly do not use splitters for both strimer plus + uni fans.

Hi Gouenji Shuuya, welcome to my channel. Yes these looks good and best is Galahad II Trinity Performance. You can watch test here. kzfaq.info/get/bejne/e5OojbeCzrC5f4U.html

Hi Pedros K. Welcome to my channel. It only comes with the pre install fans. No additional screws. You will need to get additional rad screws

Hi Storm Falcon, welcome to my channel. You will need to plug that and to use L-Connect 3 app to control the ARGB. Even if you want to use motherboard ARGB sync. You still need to set to motherboard sync on L-Connect 3 app

Hello ky, welcome to my channel. There are some great difference between normal and the SL-Infinity. 1st the SL-Infinity able to use L-Connect 3 app to perform various patterns for ARGB effects 2nd the air pressure is higher on the SL-Infinity. As for performance, it's about 1 to 2 degrees difference.

Hi Sham Ahmed, welcome to my channel. In your case, there are no way to use the controller that comes with the liquid AiO, you will need to swap out the controller to your 3pack set controller. As those come with only 7pin connection. I will advise you to do this. Swap to make use of the tripple pack fan controller. 1) 3 x AIO Radiator fans , use the single pack cable, connect the fan RPM connector directly to your motherboard CPU_FAN header. As for the ARGB connector, plug it to the triple pack controller on sync port 2 - Use your motherboard software or UEFI to control the fan RPM - Use L-Connect 3 app to contorl the argb effects - Reason for this, if your controller failed, your fan will still spin as it is to cool your CPU, which is important. So in the event if your controller failed, only argb is affected. 2) 3 x Case fan, plug using the 7pin cable to port 2 to the tripple pack controller. Use L-connect 3app to controll both fans RPM and argbs effects via L-Connect 3 app 3) 1 x rear fan, plus using the 7pin cable to port 1 to the tripple pack controller. Use L-connect 3app to controll both fans RPM and argbs effects via L-Connect 3 app

Thank you so much for the detailed reply. I really appreciate it. In the above configuration, where would I connect the 4 pin from the AIO unit itself? The other two are USB Header and SATA power. I understand to connect the 4 pin from pump into CPU Header. Finally, would your advice change if I purchase 3 individual SL-INF fans instead? Is that configuration better?@@KleoYan Thank you once again.

@@shamahmed7735 you are most welcome. for the Pump block, the 4pin must directly plug to your motherboard pump header. for Asus is AIO_PUMP and for ASrock is CPU_FAN2/W_Pump, MSI is PUMP_FAN and Gigabyte SYS_FAN#_Pump. If you have gotten the tripple pack. just stick to the configuration I have told you. if you decided to go with Single pack then the connection it's only slight difference but you have total control over the PWM of each set of fans. 1) 3 x AIO Radiator fans , use the single pack cable, connect the fan RPM connector directly to your motherboard CPU_FAN header. As for the ARGB connector, plug it to the triple pack controller port 1 - Use your motherboard software or UEFI to control the fan RPM - Use L-Connect 3 app to contorl the argb effects - Reason for this, if your controller failed, your fan will still spin as it is to cool your CPU, which is important. So in the event if your controller failed, only argb is affected. 2) 3 x Case fan, plug both 4pin (PWM) and 3pin (ARGB) to port 2 Use L-connect 3app to controll both fans RPM and argbs effects Or 2a) plug 4pin(PWM) to Motherboard Fan header and 3pin (argb) to the uni controller Use motherboard to control the fan RPM and L-Connect 3app for the argb effects. 3) 1 x rear fan, plug both 4pin (PWM) and 3pin (ARGB) to port 2 Use L-connect 3app to controll both fans RPM and argbs effects Or 3a) plug 4pin(PWM) to Motherboard Fan header and 3pin (argb) to the uni controller Use motherboard to control the fan RPM and L-Connect 3app for the argb effects.

Sir, you are a true gent. Thank you so much once again, I will attempt this over the weekend with your instructions. @@KleoYan

@@shamahmed7735 you are most welcome, all the best with your build.

Hi Bellavi, welcome to my channel. you are not able to do so as the SL V2 and AL V2 have different profiles which you will need different uni controller. This will explain further kzfaq.info/get/bejne/ec2mqLh3yszKaIk.htmlsi=xzSZ0_iNC6QverlV

Hi Zade Wolve, welcome to my channel. though I have not release the perfomance content of all these GA II Trinity aio, either the SL-Inf 120 or Performance are both good choice as the fans on the SL-Inf and Performance, both yeild better results. between the SL-Inf and Performance, it's about 3 to 5 degrees difference on default load of a AMD 7950X.

Hello cr9731, welcome to my channel. Pardon me. Do you mind to list done you Lian Li components as I don’t understand what you have mentioned. Thank you.

Hi Kevin Eureka welcome to my channel. for the pump you will need to use the L-Connect 3 app, else for the fans, you can plug the 4pin directly to any of your fan headers but the argb you will still need the connector that is provided. the other end you can plug directly to the argb motherboard header. you will need to figure it yourself on the connection.

Hi Aesir, welcome to my channel, you can buy this to split and use another controller. www.aliexpress.com/item/1005005121350909.html

Hi Coopa, welcome to my channel. which fans are you trying to connect, are they of the same type of fans?

@@KleoYan Hi, yes they are. I have one more trinity two but its broken. Im using the fans for my case. I cut off the cable and soldered on an ARGB connector. Its working for me. I have now also bought the adapter cable and will use it. So rebuild again. 😂

@@Antidot1981 I see. If you have altered the cables and connecting them directly to the motherboard header and ARGB connect. you will be needing your motherboard to control the PWM and ARGB of these fans. To be honest I can’t picture what you are doing. Just make sure if you are connecting this fans (PWM) to your motherboard header. Do not exceed 3 fans if the header is of 1a load. Good luck and all the best.

Hi Sven, I have tested you don’t have to plug that and just use the L-Connect 3 app.

Hi Napster Cheung, welcome to my channel. You should swap the controller and use the 7pin on your AIO. Anywhere you will need 2 x 2.0 USB header on your motherboard. one is for your AIO block and another is for your SL INF or SL V2. If you are using all three. You will need got get a usb splitter as your motherboard might only have 2 2.0 USB header.

​@@KleoYan Thank you for your prompt reply. The current situation is the RGB of the pump cannot be detect and control using the L-connect 3 with SLV2 controller. When the power is connected, there is light on the pump (red and green). After the normal start up, it will light for a sec. When OS ready, the light will be gone. Everything is working normally and can be comfigured, except the rgb of the pump. (Both AIO and 3 pack SL fan are using 7pin to connect to SLV2 controller). Thank you.

@@napster556 are you able to check on windows under device manager > universal series bus devices, do you see the Lian Li controllers? Or do you just see only the SL V2 controller?

Hi ClearSkiesAstro, welcome to my channel and thank you for your feedback.

HI Jonathan Häußler, welcome to my channel. Yes the SL-INF are running more quiet compared to the original but do take note that the original are designed to have more static pressure. the SL Inf they are general fans for both radiator and also as case fans.

@@KleoYanThanks for the info. I'm going with an arctic liquid freeze 3 after all because I read about a lot of folks having issues with the pump after a few months with the Lian Lis. The Arctic Freezer is apperantly also very quiet (especially the pump) which is important to me.

@@j0n1 Hi, thanks for the update. All the best with your build too. 😉

Hi Mark Cust, welcome to my channel. I use to think like what you think, which is just to connect the ARGB connector of the pump the the ARGB motherboard header. but, it does not work that way. you will need to plug the USB cable between the pump and motherboard, using L-Connect application to control the argb. if you intend to just use the motherboard argb software, you will still need to have L-connect 3 app to set sync to motherboard mode.

@@KleoYan ahh okay, so nothing is wrong, no faulty aio, just need the software to turn the rgbs on. Okay got you. Thanks alot!

@@markcust6928 you are most welcome..

Hi SiSone, welcome back. The difference is the performance has a double fin stack but the fans are not arg. You can however purchase add on strips to have ARGB at the side of the fans. As for the SL INF. It’s just like the normal GA II trinity. Just that the fans are of SL Inf with ARGB effects

Thank you for your answer do they cool the same?@@KleoYan

@@SirSone1 performance are slightly better but I would just stick to GA II Trinity SL INF is you want ARGB. Reason is the temperature results are of only 3 to 5 degrees difference. Btw my room temperature is at 30 degrees celcius when testing a AMD 7950X

@@KleoYan Thank you for the information this was very useful so in other words the GA II trinity SL INF is an excellent option for i9 13900k I guess

@@SirSone1 yup that’s right and you are most welcome. All the best with your build too 😉

Hi Mattia Gatti, welcome to my channel and yes you can. 😉

@@KleoYan What would you choose if you had to recommend me a 360 liquid AIO for my NZXT H9 flow? And top mounted or side mounted? Thank you so much!

@@mattiagatti1200 Hi and welcome back. it greatly depends on which processor you will be using. you might want to check out these 8 AIOs which I've tested. kzfaq.info/get/bejne/mcdiraqEtty7n5s.html as this test does shows which AIO are good for either Intel or AMD.

@@Voltomess hi welcome to my channel. For me I have been using these and the LCD version without issues. If you are wary of this, you can look for EK nucleus or the Deepcool Mystique. As for 14900KS. The Galahad II Trinity performance or the Galahad II LCD will be the option. To cool this processor.

hi InvisiblatorYT, welcome to my channel, are you able to see under device manager or management, under the Universal Serial Bus Devices. do you see the Lian Li device and version listed? if you dont see that, you might want to change to another USB header on your motherboard and try again.

one last check, did you download the correct L-Connect 3 app? you should get this version Current version: v1.7.2 Posted: 10/20/2023 lian-li.com/l-connect3/

Hi SirSone, welcome back again 😁 the GA II trinity are designed for highend processors like the AMD 7950X, 7950X3D and your intel i9 13900K or KS. They will be able to cool your processor.

Hi NannyMcFence🫠 , you will be able to connect your reverse fans to the uni controller that comes with the liquid AIO. just make sure is of a single pack and not the tripple pack. as tripple pack cables are slightly different.

@@KleoYan alright thank you

@@NannyMcFence you are welcome and all the best with your build too.

@@KleoYan Thanks I appreciate it😀

@@NannyMcFence 😬 my pleasure.

Hi Andy, welcome to my channel. thank you for your feedback, I have no issues with the pump, I adivse you raise an RMA with Lian Li at lian-li.com/faq/, scroll down a currently they are on holidays.

@@KleoYan Hi Kleo I put an RMA in with Lian Li Thanks but no reply from retailer... I contacted them first. Not happy :(

@@user-jz1xi2vm9m you are most welcome. they should get back to you once they are back after October 10th.

Hi Exige Tech, welcome to my channel, regarding about the pumb technology if the GA II Trinity, I have no info on them. so sorry about it.

@@KleoYan ah ok, thx anyway!

@@ExigeTech you are most welcome. Let me see what I can find out. I will ask via email and if I do get an answer, I will update you here. Thank you.

@@KleoYan yeah ty!

Hi Rizka Al Ghazali, welcome to my channel. Yes you can just use the L-Connect 3 to control the ARGB if your motherboard do not have an ARGB header. It’s perfectly fine.

@@KleoYan thanks 😁😁🙏🏻

@@TheRizkaalfarisi you are most welcome. All the best with your build too. 😉

Hi Ink Ing, welcome to my channel. The illustration above is just showing where to plug those 4pin PWM and yes. You should be either using the CPU_FAN or AIO_PUMP. the arrangement are as follow 1) GA II Trinity - Either CPU_FAN or AIO_PUMP as CPU_OPT shares the same setting as CPU_FAN (if you choose to bypass L-Connect 3 app and to make use of the motherboard UEFI or Software) 2) GA II Trinity SL-INF - The pump block will goes to AIO_PUMP and the SL-INF 120 will goes to CPU_FAN 3) GA II Trinity Performance - Either CPU_FAN or AIO_PUMP as CPU_OPT shares the same setting as CPU_FAN (if you choose to bypass L-Connect 3 app and to make use of the motherboard UEFI or Software)

​@KleoYan thanks! Btw, wondering if i wanna control the lian li sl inf fans through the lian li hub (LL l connect thingy), can i connect the fan pwm headers to the cpu fan then the argb header to the l connect hub?

@@inking3035 If you plug your fans PWM connector to your motherboard direct, you will need to use your motherboard UEFI / Software to control the PWM of the fans, else your argb will be controlled using the L-Connect 3app. Infact what you've mentioned is even better as in the event if your uni fan hub failed, only your argb will not light up as your fans pwm are controller directly from your motherboard UEFI/software.

@@Aronzzi89 hi and welcome to my channel. have you tried on another USB 2.0 header on your motherboard? that will be the first thing to test, also is the controller detected in Device Manager under Universal Serial Bus Devices?

Hi Jong Kanel, welcome to my channel. I was not aware of any changes. Mind to take some pictures and send it at godzylatech@gmail.com I will check with them on this. Thank you!

Hi vbs, welcome to my channel. the pump as usual, directly to motherboard pump header (W_PUMP / AIO_PUMP / PUMP_FAN) as for your radiator fans, at the end of the fans, plug the 4Pin PWM directly to your motherboard CPU_FAN. as for the 3pin 5v argb, connect to cable N and plug the other end to the pump. This way, you only control the Pump PWM and argb effects of your fans through L-Connect 3 app. Your radiator fans PWM will be controlled directly on your motherboard UEFI/Bios.

@@KleoYan Thanks for the response, the only problem here is my motherboard cpu fan provide max 1A 12v and the fans at max speed need 0.36A, 3 x 0.36 = 1.08A, you think its fine for the motherboard cpu fan this extra 8% power or another option is using the w_pump for the fans, on my motherboard it can provide 3A 12v

@@vbs0 hi, just to check, which motherboard brand and model are you using?

@@KleoYan Trinity II 360 default version (not performance or infinity fan), Asus TUF x670E am5

@@vbs0you are right. Plug to W_PUMP. That’s the only option and based on the board layout. It’s at the bottom. The cable from your AIO might not reach it. Give it a try. If can’t, you will need to get a fan extension.

Hello johndoo doo, welcome to my channel. I notice for each type, there is a small circular plug besides the radiator hoses, but I cannot confirm if it's a refill port and am not going to pry open that to void the warranty.

Hi Qatar1701, welcome to my channel. Nope you can't do that as the firmware is different on the SL-Infinity controller.

@@KleoYanOkay Thanks.

@@Qatar-uo9ml you are most welcome and all the best with your build.

@@KleoYan Thx, atm im Waiting for the Inf 120 Reverse Blade to get Avaible Again, anyways. I found an Post on the Lian Li Reddit, pointing out this Pointless ARGB Hub on the AIO instead using an normal Inf Controller. The Lian Li Tech Support Responded there and Told that it would work out If you take one of the 4 included connections(Of the Inf Fan Triple Pack) and use it, you should be able to use it via the INF controller.If possible I would like to post the link to it as I'm a little confused now. Have you tried it and can you say that it doesn't work or is that just your guess?

@@Qatar-uo9ml hmm. I donno which thread you are referring to. if you got the Trinity SL-Inf Liquid AIO, it somes with the uni controller for your SL-INF, you can purchase single reverseblade, diasy chained them and use the single pack cable to connect to the uni controller. Unless you already purchase a triple pack which comes with a uni fan controller. then swap out the Liquid AIO uni fan controller to the triple pack set. reason is.. a triple pack set comes with 7pin (ARGB+PWM) connectors and not split 3pin (ARGB) and 4pin (PWM), thats why your triple pack fans is not able to connect to the liquid AIO uni fan controller.

Hi Genadi 'Enomir' Georgiev, the performance does not come with ARGB fans, but the block does have argb, you can make use to the L-Connected app 3 to control that and all is needed is to plug the USB Cable between your pump block to your motherboard USB 2.0 socket. No argb 3pin is needed.

@@KleoYan thank you very much. I was worried for a sec cuz I ordered one with extended warranty already.

@@TaLa7aMcHo you are most welcome. All the best with your build and just one pointer. When you install this unit. Make sure the pump header is to your AIO_Pump or W_Pump header from your motherboard and NOT cpu_fan or chass_fan or sys_fan. As the pump will work well with those headers I have mentioned. At least it will provide the correct ampere to your pump

One more thing. If I decide to later on switch to the unifans with the hub only for the aRGB, would that be the same or a downgrade. And would I need a 3 pin aRGB connector ? What would be my options for rgb on the cooler if my 3-pins are blown out ?

@@TaLa7aMcHo hi, same thing apply. you dont need to have a 3pin argb header on the motherboard but will need another USB Header for the uni controller which controls the uni fan's argb. and it won't be a degrade if you choose uni fans which are of V2 .. example SL120 V2, AL120 V2.. or even the SL Inf 120.

Hi howtotech, welcome to my channel. Yup I made a mistake. Do pardon me and thank you for pointing out.

no problem. hope it helped as that was what i was aiming to do. will subscribe loved the informative video @@KleoYan

@@georgewhite5794 I see. Thanks for point out my mistake again and also all the best with your build 😉

Will it be fine?

Hi Soma TW2, welcome to my channel. What you can do is to use the 3 pack Uni controller plug the 3 pack fans to the controller. Then use the 3 pack set cable (7pin) and plug it to the GA II Trinity SL-Inf fans. That will work.

@KleoYan Thank you. yeah, I am gonna to try. Hope I can set in L-Connect 3 those fans as CPU ones. If I had like more usb headers, this would not be a problem at all.

@@SomaTW2 ok dokie. All the very best with your build. 😉

Hi MkT* ;D, welcome to my channel. I would say the GA II LCD and GA II Trinity performance are much better, you can watch this as a comparision kzfaq.info/get/bejne/e5OojbeCzrC5f4U.htmlsi=k-dJsol4YHfBWwXz

@@KleoYan Thanks for the quick response bro. I just watched the video. Unfortunately here in my country (Brazil), the LCD version did not arrive. while the performance arrived, but it doesn't have ARGB, considering that I have 7 inf fans. very sad, I really don't know what to buy. i7 14700k. great videos!

@@KleoYan here we have at good prices the: Lt720, Ls720wh, lian li sl inf, nzxt kraken 360, asus rog strix LC II 360 and asus ryuo III 360. May god bless you.

@@markituoboy hi, so sorry to hear that and base on your list. It greatly depends on your budget and the worth of the Liquid AIO. For my own personal preference. I will just grab the LT720 which is the cheapest here in my country. It performs extremely well. Not that others are not doing good but I judge based on price to performance. If you wanted both, then I will go for the Ryujin III.

Hi Melvin, good morning and thank you for your feedback. In my honest opinion these are great coolers with heaps of improvement. Just that a lot having trouble with the application and they way they are connected. Can be confusing if do not take time to read the instructions manual.

it's still trash , depends on your luck , i paid like 210€ performance version, got defected pump , burned my cpu and SSD , already saw on reddit that people have problems with pump

Hi BabaGames, welcome to my channel. I like to check, which uni fans are you using and does your uni fan controller have 2 additional ports which says sync 2 and sync 4? if you have that, all is needed is a converter for you to plug your Galahad argb to either sync 2 or sync 4. you will need to look for the lian li ARGB kit.

@@KleoYan i would want to use the uni fans sl-inf fans and the controller which comes with the galahad 2. i believe this controller does not have the additional sync ports as you suggested. I could buy this controller seperatly if needed

@@MrCan3112 hang on a minute.. I thought you are refering to Galahad, but ended up you have the GA II Trinitry SL-Inf, if thats the case. your pump should have a USB connector that goes to you the motherboard. you dont need to plus it to your SL-Infinity controller. therefore you only need 2 usb 2.0 header on your motherboard. one for your Pump and other for your SL-Inf controller. that's all is needed to control all ARGB effects in L-Connect 3.

@@KleoYan Oh ok my bad. Sorry for not being precise. Thank you very much

@@KleoYan one last question. Do you know if the rgb effects of fans and galahad 2 start during the boot up of my system, when controlled with l connect?

Hi zero two, welcome to my channel. Yes you can. on L-Connect 3, click on Quick Sync Lighting, set it to sync to motherboard. but when you do so, both your AIO and fans will follow motherboard argb effects, you can't separate it.

@@KleoYan thanks, so I can only separate on sl infinity version ?

@@zerotwo57 for GA II Trinity SL, the fans have an additional control box.. thats why you can just set the fans to follow motherboard sync while your AIO Pump follows L-Connect 3 app.

I can only fit 240mm

Hi Zoomer, welcome to my channel. For the performance AIO. It does not come in 240. You left with the GA II Trinity and is either with the normal fans or the SL Infinity fans. Anyway your 7800X3D is not toasty. Therefore the 240 GA II Trinity is good enough to drive your processor.

Hi achraf tchanderli braham, welcome to my channel and pardon me for the late reply. You will first need to have your Windows OS detact your Uni Hub. if it does not detect. You can't control the fan rgb or pwm. here is a guide which might aid you. kzfaq.info/get/bejne/ec2mqLh3yszKaIk.htmlsi=whIwm5QWj6aaGOfz and as for your ROG Strix motherboard, so long there is a connection to the fan header call CPU_FAN , you will be fine or you can disable it by ignoring the detection, the warning message will be gone. you can do this in your UEFI under fan monitoring. just set CPU_FAN to ignore.

@@KleoYan hello, and thank you for your replay, I apreciate a lot. The OS detect correctly the GA 2 trinity, i plugged the fans to the pump, then i plugged the pump to CPU_Fan it worked well i can control RGB with the motherboard program, but with L connect it sais no fan products detected, i thought it's weird, i installed the 1.75 version and it seems to work better but still there is the same message no fan products detected,so i don't know if im plugging it correctly or im doing a mistake, thank you in advance ps: i have Lian Li GA II 240 trinity not infinity SL it's without the UNI fan

@@charonsybel you should plug the pump to the pump header and radiator fans to cpu_fan header

​@@KleoYan but the radiator fans in the video you plugged them into the pump right? or i take off cable N and plug the radiator fans directly to the cpu_fan header?

@@charonsybel the right way is to connect as according to Lian Li's instruction. The issue with your mobo is it has a build in function where by if no fans are connected to the CPU_FAN header or no signal after if you did plug your fans in.. you will get this prompt. in your case yes you can do that too. infact is better to control your fan directly from the motherboard (PWM) and leave only the argb to be controlled by L-Connect 3 app.

Hello PedrOps, welcome to my channel. Here you go kzfaq.info/get/bejne/rpp-m66Gld-XmoU.html and kzfaq.info/get/bejne/e5OojbeCzrC5f4U.html

Hi Асет Каратаев, yes you can but performance will drop as the fans on the Performance fans are high static pressure fans.

​@KleoYan Bro thanks for the advice😊

But Galahad II Trinity Performance model with sl-inf fans will be better nearly regular galahad II Trinity Sl-inf model?😅

@@user-pi1iu1gl3y hmm I find no point to get performance and to compromise the performance. If that’s the case should just get the GA II Trinity SL Inf

Hi Ratha Siv, welcome to my channel and thank your for sharing, greatly appreciated it 👍😉

Hi Night Owl, as if you purchase single pack SL-Inf 120 fans that comes with the split connect (1 x 4pin PWM Fan and 1 x 3pin ARGB) then is of no issue. it is prefectly safe but make sure you do not plug more than 4 fans at each port and no merge or brigding between fans. it will overload.

@@KleoYan Ah I see, thanks for the quick response.

@@cloudsaremashedpotato you are most welcome and all the best with your build too.

Hi Aronzzi, welcome to my channel. For this, I have no idea it’s different. Maybe you can check it on the instruction manual if the AMD bracket is what you see on it drive.google.com/file/d/1UgTpJFkwk4YVWHfIV7oGUrWDJxXh8xwU/view?usp=drivesdk

@@Aronzzi89 ​​⁠you are most welcome. If that’s the case, either contact your seller or contact Lian Li to provide you the necessary. All the very best 👍

@@Aronzzi89 ​​⁠you are most welcome. If that’s the case, either contact your seller or contact nLian Li to provide you the necessary. All the very best 👍

@@Aronzzi89 i see, ok that's good to know and thank you for the updates... all the best with your build 😉