How To Shave An Engine Bay | FULL TUTORIAL

No video

How To Shave An Engine Bay | FULL TUTORIAL | CIVIC BUILD SERIES

Рет қаралды 43,208

Күн бұрын

in this video i will be showing you the process of shaving an engine bay along with great products to make the job easier. i will have a list provided below ( i do get a kickback from this). You will learn the proper way to sand, weld, make metal fill in sheets and the basics of painting. I hope you enjoy it and if you do be sure to like and subscribe!
SPONSORSHIPS INQUIRE HERE:
Bccbodyshop@gmail.com
products and parts i used in this video are:
3' hook it da sand paper
amzn.to/3wvCcgY
3' da velcro interface pad
amzn.to/44SMT9R
3' da velcro attachment to use hook it paper
amzn.to/4bO4Clj
3' DA sander
amzn.to/3ULC6cV
6'' DA sander
amzn.to/3V8nzZh
6 da sander hook it attachment
amzn.to/3UQGEio
6 da sander interface pad
amzn.to/3K9hExR
HOOK IT SAND PAPER
amzn.to/3K8n7F7
belt sander
amzn.to/3QRijHP
belt sanding paper
amzn.to/3QSq5RI
solveant wipes (for cleaning surface prior to painting)
amzn.to/3wFvxAO
SATA 5000B RP 1.3 PAINT GUN
amzn.to/3K9hZR9
high build primer can
amzn.to/3KaorHI
self etch primer can
amzn.to/44MrbEo
PEARL PIGMENTS
amzn.to/3WOpT9X
2K PRIMER
amzn.to/3VhiBux
INTERCOAT CLEAR(NEEDED FOR PEARL!)
amzn.to/3wDVbpB
INTERCOAT CLEAR REDUCER
amzn.to/3QSzid7
GLAZE PUTTY
amzn.to/3WNAYIt
GUIDE COAT
amzn.to/3WPUqEE
BODY FILLER
amzn.to/4bKhgS9
SPREADERS
amzn.to/3ykbRTm
MIXING TRAY
amzn.to/4bEuDUx
TACK CLOTHES
amzn.to/4dKcu94
PLASTIC CAR COVER FOR PAINTING
amzn.to/3yuWnfC
HOOK IT SANDING BLOCK KIT
amzn.to/3UK9nW5
VELCRO BOARD PAPER
80 amzn.to/3K8r50A
120 amzn.to/3yuWury
150 amzn.to/3KaerhG
220 amzn.to/3K9uts0
320 amzn.to/3K9QiaS

Пікірлер: 106

@HisNameIsTater Ай бұрын

Your tab idea is slick, I use something similar when I'm fabricating, I'll just tack a rod on. Little things make all the diference. That's what I tell my wife anyway

@BrokeVetGarage Ай бұрын

Hahaha that’s why my gf has little hands. Stupid little tricks of the trade that make life a lot easier.

@bawxofchawclets4836 3 ай бұрын

I know for a fact I’m going to randomly remember this video in 3 years . Even though I have no mechanic skill or aptitude I just want paint and do a 3sgte swap on 96 Toyota rav4

@BrokeVetGarage 3 ай бұрын

I started out at 15. I bought my first civic and got to welding. It turned out like hot garbage but failure has been the best lesson for me. No one in my family knew anything about bodywork/paint. Start on some junk parts and work your way up until you get the confidence to do it man! Thanks for watching.

@tiocharlye 3 ай бұрын

Tienes que estar orgulloso de este trabajo, como decimos en Colombia, la experiencia no se improvisa. Experiencia, como dices, desde los 15 años, no quisiera meter un motor aho

@BrokeVetGarage 3 ай бұрын

@@tiocharlye Gracias mi amiga

@slackerzsincity8822 3 ай бұрын

Sheez, just thinking about the amount of work makes me not want to do it, but when I see the final product makes me want to do it.

@BrokeVetGarage 3 ай бұрын

You don’t have to get this crazy with it.

@JacobLotz-kx2hu 3 ай бұрын

One of the best videos I’ve seen on shaving an engine bay this is going to help me so much with mine!

@BrokeVetGarage 3 ай бұрын

That’s great to hear man! Definitely appreciate it.

@robs85gmc 20 сағат бұрын

sweet work man, that finger sander works amazing. Im gonna have to get one

@BrokeVetGarage 20 сағат бұрын

One of the hardest working pieces of equipment in the shop. You’ll love it.

@DaBadNewz 19 күн бұрын

Outstanding video man! Great angles, thorough explanations, and it looks like it came out really nice.

@BrokeVetGarage 19 күн бұрын

Much appreciated brother 🙏. I

@KKDriver 3 ай бұрын

Wish i could’ve watched this before i did mine! you did absolutely amazing man, great work🔥🔥

@BrokeVetGarage 3 ай бұрын

Thank you 🙌

@catsinflames4598 3 күн бұрын

I'd pay someone to do this quality work

@BrokeVetGarage 3 күн бұрын

You would be paying a LOT. I would price this over 5k.

@yuryv.2188 3 ай бұрын

enjoyed every bit of this video can watch for another hour man so satisfying with the result

@BrokeVetGarage 3 ай бұрын

Glad to hear it! Thank you 🙏

@marcosathens8140 Ай бұрын

Good Job. You have "the touch" as we used to say. Best of luck with your project.

@BrokeVetGarage Ай бұрын

Thank you sir

@BrokeVetGarage 3 ай бұрын

I just added links to everything I used in the description of the video. If I missed something you have questions about just lmk.

@76dro 2 күн бұрын

not boring to watch, thank you for the video ❤‍🔥

@BrokeVetGarage 2 күн бұрын

Glad you enjoyed!

@dartology 3 ай бұрын

Tons of work in that mate. Looks fantastic and the video has great tips too. Thank you 🙏🏻

@BrokeVetGarage 3 ай бұрын

Much appreciated man! Glad you liked it.

@AJVAN_ 3 ай бұрын

Amazing hard work. I will be doing similar thing to my Celica as soon as I build a garage. The only thing I would do differently is the paint base and pearl. Black with light blue pearl would look amazing.

@BrokeVetGarage 3 ай бұрын

That’s what is recommended. I made the base coat for this. Personal preference.

@desertstvrm 2 ай бұрын

Boyeh I do body work 48 hours a day, I started this the second my mother slipped me out. I don’t need advice from you brother. Great video bro for real though I’m saving this!!!!

@desertstvrm 2 ай бұрын

Oh and a tip for your paper you use to tape, try putting a cheap painters plastic from dollar tree and make a cover with it

@BrokeVetGarage 2 ай бұрын

That’s a solid tip man! Thank you

@deimosphob 3 ай бұрын

If your shock towers are warped you can always add shock tower braces and cap it off

@clne36 3 ай бұрын

My gosh man this looks SOOOO good! Seriously impressive. All the time and effort you put in paid off. Will you come finish mine haha!

@BrokeVetGarage 3 ай бұрын

Yeah, right after I get feeling back in my fingers 😂 Just wait until I have the whole car looking like this! Thanks man, much appreciated!

@gateaccess818 3 ай бұрын

bro that color is fucking fire!!! whole car this??? sheeeeeesh. must see more!

@kateweirauch5678 3 ай бұрын

That is BEAUTIFUL! You are so talented. And handsome 👀

@BrokeVetGarage 3 ай бұрын

Thanks babe 😘

@Dblpumped 3 ай бұрын

Looks great !...im also doing a pearl color right now. Keep the content coming !

@BrokeVetGarage 3 ай бұрын

Thanks man! Pearls the way!

@Willis-de5hx 3 ай бұрын

Awesome work 👍

@BrokeVetGarage 3 ай бұрын

Appreciate it man!

@jjtrades7186 3 ай бұрын

Nice work man

@BrokeVetGarage 3 ай бұрын

Thx man

@restomodswede2245 Ай бұрын

Oh no, now I need to do this next time my engine is out. :)

@TheJNALife747 3 ай бұрын

AMAZING WORK BRO💯THANKS FOR THE CONTENT

@BrokeVetGarage 3 ай бұрын

Glad you enjoy it man! More to come.

@aadd3538 2 ай бұрын

My guide coat is black satin

@BrokeVetGarage 2 ай бұрын

My guide coat is whatever spray paint I have laying around

@mikewegner2798 3 ай бұрын

Man that looks 🔥

@BrokeVetGarage 3 ай бұрын

Your old civic is going to be amazing!

@jacobpooler6299 3 ай бұрын

other than practice, what advice can you give to someone trying to learn how to fill holes with mig?, watching you fill the rad support holes was a eureka moment for me lol

@BrokeVetGarage 3 ай бұрын

Grind and clean the metal you are going to weld. Keep your tip off the metal. Keep the tip clean, you will know when it’s not. Use Aragon if you have the hookup. Don’t chase burn throughs, let it cool off and come back to it. Try drilling some holes in a junk fender and practice a little until you feel comfortable. Hope this helps.

@jacobpooler6299 3 ай бұрын

@@BrokeVetGarage absolutely this helps, I appreciate it man! Thank you for your service sir!

@BrokeVetGarage 3 ай бұрын

Happy to help. Good luck man.

@vaughandieselsweeklyword9331 3 ай бұрын

Not sure if i missed it or not but did you stitch weld where the seam sealer goes

@BrokeVetGarage 3 ай бұрын

I did. I had so much video (over 130). I was just trying to narrow it down so it didn’t get so muddy.

@jonelliott4985 2 ай бұрын

Nice job on the engine bay bro... but I kinda dontbagree with you on the no way people can do primer in only two coats... the thing is it depends on a person's experience and technique personally I used to do my prep fully before primer basically if you do your filler in coats that are designed to build fill and smooth using the different levels of filler that are colour coded you can square away all defects in the filler stage so when your first primer layer goes on with a couple over top to wet flat it an see any more low spots which should be none then clean it prime it again with its top coat primer wet flat then use your chosen colour to flow coat wet flat it then spray second layer of colour wet flat lawyer wet flat lawyer wet flat then punish with a sponge mop and curing paste mixed with a good was then buff with sheep's wool mop and done only time you would need more than two coats of primer is if your prep work ie body work and filler was not done precise...any way I might dis agree with your statement of primer coats but I think you did a helps job with your engine bay an I love the twotone colour flip in that paint it looks well slick budd

@BrokeVetGarage 2 ай бұрын

I’m talking in regards to a restoration project. I don’t need to do multiple primer sessions for a collision repair. When I do a full restoration the entire car gets block sanded with at minimum 2 sessions of 4 coats. Even if there’s no damage. But I was mainly stressing it in this bay. Have you ever done a full shaved bay before? It’s not like doing any other body work that’s for sure. I don’t wet sand primer. I don’t understand some of your wording either by helps hand?

@user-vh3mk2hn3q 3 ай бұрын

How would you run the engine harness underneath the frame?… what color pearl you put in the clear coat it LOOKS good

@BrokeVetGarage 3 ай бұрын

I’m not going to run it through the frame. Subscribe if your not already and you will see how I’ll end up doing it! The pearl is applied with an intercoat clear, I’ll put the materials in the description soon. I’m working on a list right now. Much appreciated man!

@JoshIW155 16 күн бұрын

what’s your welder set up ? and what wire are you using

@BrokeVetGarage 16 күн бұрын

It’s a Hobart. I believe it’s a 140? And .025 with gas. I usually use .30 for bodywork but I have a huge spool of this.

@tjhemrick 2 ай бұрын

What color/brand is that? It's 🔥.

@BrokeVetGarage 2 ай бұрын

The pearl is in the description. The base is a custom color I made. Thanks man!

@geometric1227 3 ай бұрын

Damn, I was gonna have a go at doing something like this in my skyline. I have next to no experience with body work so I might remove this from the list 🤣 All up how many hours do you think you put into the engine bay?

@BrokeVetGarage 3 ай бұрын

It took around 40-50 hours. It’s no small task man. Skyline huh? Nice!

@geometric1227 3 ай бұрын

Your bay looks mint 👌 I have about zero fab and paint skills so it'll be a learn on the go thing for me. I'm guessing you're a military vet? I did 15 years in the Australian air force, now my skyline build is pretty much my daily hobby as I can't work any more. I subbed to the channel and look forward to seeing more of your content and stealing some tips from ya.

@BrokeVetGarage 3 ай бұрын

Happy to help. Your import laws are a lot more lax over there! I did 6, army. Awesome man, hope you learn a thing or two!

@davidd727 3 ай бұрын

In the beginning. The seam sealer. Did you remove all of it? If so did you weld for strength and then cover it with body filler?

@BrokeVetGarage 3 ай бұрын

Yes I welded the joints together. Some stuff I didn’t get filmed. There were already over 130 separate videos for this.

@davidd727 3 ай бұрын

@@BrokeVetGarage great job. I’m hoping to get started on my hatch shell one day.

@BrokeVetGarage 3 ай бұрын

@@davidd727 it’s a rough time lol but just dive in man! Thanks for watching.

@gamercoolapple1 3 ай бұрын

What colors did you use for base and top color ?

@BrokeVetGarage 3 ай бұрын

Custom color I mixed from my mix bank. The pearl I used is in the description as well.

@juanespinoza-ue4fy 3 ай бұрын

🔥🔥🔥

@BrokeVetGarage 3 ай бұрын

Appreciate it bro

@humongouscodger437 Ай бұрын

Do you sand all the way down to 600 with a belt sander

@BrokeVetGarage Ай бұрын

I’m confused by what you are asking?

@humongouscodger437 Ай бұрын

@@BrokeVetGarage it seems very tedious I’m trying to figure out the best way to sand I know you were talking about the belt sander and 3 inch orbital

@BrokeVetGarage Ай бұрын

@@humongouscodger437 I sand the bay with 150 before I start any body work and a scotch bright, the belt sander is 60 grit for the welds.

@YardManJZ Ай бұрын

What did you do to fill the areas where you removed seam sealer ?

@BrokeVetGarage Ай бұрын

Butt Welded, ground them down and then filled them.

@YardManJZ Ай бұрын

@@BrokeVetGarageI am also curious as to why you did Dolphin Glaze, Body Filler , then Dolphin Glaze Again ? Wouldn’t just body filler work in this case ?

@BrokeVetGarage Ай бұрын

@@YardManJZ It doesn’t matter how you do it. You could just use body filler. The glaze just sands easier. Body filler is thicker and doesn’t spread as easy. I do my last coat with glaze just to do my final shape and to fill in any pin holes from the filler.

@YardManJZ Ай бұрын

@@BrokeVetGarage thanks man . Appreciate your response . Going to try to replicate this on a project here for the first time

@BrokeVetGarage Ай бұрын

@@YardManJZ no problem man. I’ll tell you this. You can use just body filler. Glaze is kind of a luxury, not a necessity. Just keep an eye out for pin holes from the filler. And don’t use bondo brand lol it’s like sanding cement.

@TheJNALife747 3 ай бұрын

🔥🔥🔥🔥

@BrokeVetGarage 3 ай бұрын

Can’t wait to get the whole car in this!!

@TheJNALife747 3 ай бұрын

@@BrokeVetGarage I CANT WAIT TO SEE IT BRO..ILL BE TUNED IN ,IM SUBSCRIBED…

@cooliecrewspeedshop 3 ай бұрын

What grit belt sand paper did you use for grinding the excess weld patches?

@BrokeVetGarage 3 ай бұрын

For the belt sander I was running 60.

@gateaccess818 3 ай бұрын

carbon accents against this color would be LETHAL!!!!

@tonykartracer8032 3 ай бұрын

I dunno, I don't like shaved engine bay. I like it to be a bit of spaghetti mess under the hood..... just makes it look more real to me. Shaved engine bays with wire tuck everywhere just look too cartoony for me, if that makes any sense. Hehe. With that said, it looks like you know what you are doing so keep it up.

@BrokeVetGarage 3 ай бұрын

My first shaved bay. Feels like it’s appropriate for what I’ll have in it :)

@gateaccess818 3 ай бұрын

@16:59, n fn lie. my bay probe has 5 coats of filler, primer, ect. so much fn sanding. peoples jaws drop when i tell them the cost to shave their bay... they have no idea how bad that shit really is haha worht. fuck yes. but fun.. not really... lmfao

@BrokeVetGarage 3 ай бұрын

Yeah I would never do one for someone lol this was enough 😆. New video comes out tomorrow! Thanks for the compliments!

@mattbush315 13 күн бұрын

@@BrokeVetGarage if you had to guess, how many hours do you think you have in the bay? Great work in showing the effort it takes and well done!

@BrokeVetGarage 13 күн бұрын

@@mattbush315 I would say probably 40 hours. Thanks man. But that was over a long stretch of tinkering. Could be less.