Try a speedometer cable, they work fantastic. Another trick is, fold a zip tie in 1/2 and put the loop into the hole until it fits tight against the inner wall of the tubing. Fish your wire past the zip tie, pull the folded zip tie back out and it should pull your wire out in the loop. I own Audio 2000, that's an old car audio trick.

i love how you explained how the power works on the can am many people leave that out in there videos

Thanks for the video! Incredibly helpful to run the wiring!

For tight runs, I've cut one of the wires 6" short and the trimmer (or other pull string) replaces that wire. This only works if you have the wire you can spare... After the run I clip the wires so they are the same length wasting about 6" of wire. Also, I pull the electrical tape tight / stretching it so it is thinner. This can make a difference in how easy a line pulls through a narrow spot. Your method here is great, I just hope this tip can help make it that little bit easier next time. I'm definitely using the info you shared to get my light bar put up there when the time comes. I'm going to see if I can get my whips wired that way.

Thanks for show us, good job 👏🏼👏🏼👏🏼

Thanks homie. The light worked perfectly!!

This is a trip! I don’t even own a UTV and I’ve now come across your channel twice looking for how-tos on projects for my Jeep. Last time it was the Switch-Pros RCR Force 12 and now this. Must be a sign. I guess I’ll go with it and subscribe 😂. Great content. 👍

Awesome tips!

Trimmer line. Who knew? Always nice to see new ideas. 👍

Thank you for the video. I did not know that the Can-Am came with the bus bar

Hey brother any idea on how to run the wire thru the tube cage for my pod light and rock lights/ dome lights

It worked, thank you!

Dang! I’ve used everything feeding it through the cage in my Can Am Defender with a lot of frustration! Never thought about a freaking weed eater line....haha...thanks!

My brother needs one of Thoes light bars the Curved ones awesome video brother keep it up

Is the ignition on a positive or a negative ?

When you were pushing the wire up through the hole. You got to give it that Hawk Tuah, spit on that thang! Sorry I had to lmao Great video tho, learned a lot.

So basically I run everything to the bus bar. Put my ground to the top one the black one and then all my powers to the bottom one red accessory one correct?

I bought a Klein wire snake at Home Depot for literally 12 bucks. Works wonders.

Have to try weed wire. I’ve always used bailing wire, works good but can bunch up.

Does the 2022 maverick trail dps have the 3 posts to wire lightbars etc instead of using the battery. Thanks

Hey brother!! How are you attaching rock lights to the tube chassis. I'm using rock lights as "dome lights"

It's close to 100 degrees outside. Save me a trip to my garage? Is there a similar hole / method for running whip lights through the cage for a clean install?

What would be the cause of the light bar making noise through the speakers ? I connected the negative and positive thru the bus barn

Frank wsup ! Put a baja light on , chase light , fosgate radio , sb filter , lighted whips and now my fuse keeps popping that my radio , sb filter and well all my accessories are on what should i do ☹️

Where do you purchase your string in order to run your wire through the cage

Your video saved me from buying a fish tape that I would rarely ever use

So you got 2 reds on the bus bar, does it matter which one you land your light terminal on?

Do u have to disconnect the battery before connecting on that electrical bar

Put a lightweight string on either end and suck it through the other side with a shop vac.

Where can I find this light bar

How are you liking your utv speed cage ?

Were the rc footage

Can I be your buddy and drop off my KRX for all my led light needs?

I got the string thru the cage and couldn't fit the wires thru the cage