By request You can set up just about any HEX LED fixture this way that lets you use 6 channel mode Enjoy!
Пікірлер: 32
@dappygit2 жыл бұрын
There is so much information in these videos. I really love the main points including the list of fixture addresses and fixing the channel down to 6 from 7 which may have fixed my dimmer problem with 11 and 12th hex pars.
@theaverageguy3884 Жыл бұрын
Thanks bud you helped me out alot. Just bought the hexcon and 4 lights. If i not had this video i would probably never make it work. Pkease keep up the good work you do.
@Djtonydraper6 жыл бұрын
This is great. Straight to the point explanation. Thanks Brian.
@mysticpass5 жыл бұрын
Thank you! You make it so much clearer than the manual!
@groovetonight18485 жыл бұрын
I just bought 2 of the HEX LED Packs and this info really helped me out -Thanks Brother! Hope to see you at MBLV!
@davidchunkyonion6 жыл бұрын
You explain things very well. Even a dummy like me can follow along.
@epicevents19396 жыл бұрын
Ideally, Fixture 1 would be set to DMX channel 1. If you start it at 6, then it will occupy channels 6-11 which would overlap Fixture 2 that started at 7. For your purposes using the HexCon, it didn't matter. But, if somebody wanted to do some advanced programming using multiple fixtures with MyDMX, ShowExpress or whatever, it would cause issues.
@briansredd6 жыл бұрын
It wouldn't have worked here ether. I didn't have anything starting at d.006. The only thing I set to 6 was the Channel Mode, not the address
@epicevents19396 жыл бұрын
briansredd You are correct. My mistake. I must have looked away for a moment and missed when you changed to channel mode in the menu.
@garryroylegr6 жыл бұрын
Hi Brian great video. I'm new to DMX and I've got a Chauvet 40. I have tried to get my ADJ HEX Pars working on DMX following your video but I can't figure out what is wrong because nothing works. The lights work ok otherwise and my controller is new too and it works my moving heads. All I get on the pars is d.001 flashing set up to 6 ch I then have nodn if I press setup again and then dr-1 if I press setup again. (Different on 2nd par) I select fixture 1 and the faders have no effect at all. New leads too.
@vanceconway1882 жыл бұрын
@@garryroylegr I have the same problem? Did you find a solution.
@fredwatson383 Жыл бұрын
Good information. Thanks.
@lfdjrock6 жыл бұрын
Thank You so much for that demo on the light control it really helped!!!😉
@melissamaymusic9892 жыл бұрын
You video helped a million 🙏♥️
@machine27474 жыл бұрын
Really helped me, thank you!
@brianmacdonald29206 ай бұрын
I have a WMX1, an ADJ Operator 384 and an Elation SDC 12. I just ordered a Hexcon from Amazon. These have been discontinued. Why? (I don't know) I'm excited and looking forward to getting this. It's a no brainer and the price is excellent. It's 2024 and you did this video in 2016. How did this unit work out for you? Love to know. BTW I really enjoy your videos. I bought 2 Attco Beam 100's because of vour Attco Spot 100 video. Different lights but same platform. I love them!!!!!!
@CptnMangol5 ай бұрын
The Hex Par legs never seem to hold position, and end up sliding apart and the Hex Par light ends up falling flat. Does anyone have any suggestions, or products for keeping them locked in position?
@MrEasye25048 ай бұрын
What causes the display on Mega Hex Par Panel to keep blinking with no DMX signal when ADJ My Buddy is connected?
@DJXBOYRD3 ай бұрын
HELP. I have a light that won’t turn on: someone messed with my settings and I don’t know to get back to factory rest or to get back to normal.
@MrBoogaloo866 жыл бұрын
"Good one Brian*
@angelswithanedge6 жыл бұрын
It helped me. Thank you!
@michaeldaly79932 жыл бұрын
Thank you
@rananjerry62685 жыл бұрын
wow thank you so much for this
@MulletDragon3 жыл бұрын
thank you!
@ZoomAthletics2 жыл бұрын
Can you tell me how to set this up with DragonX 4 Bar DJ Lights to the ADJ Hexcon? I have the manual and can't figure out how to setup. Any advice would be appreciated. Thanks
@rbeergarage45933 жыл бұрын
Had do I add the stinger 2 light to this controller in addition to 4 par lights?
@oztecheventsllc50024 жыл бұрын
Great info Brian. I want to do a chase with 6 hex pars, but each one to be a different color in the chase. How would I set that up on this Hexcon controller?
@rafartconti71124 жыл бұрын
One question, that dmx works with other Brands??? Like alíen pro or SL prolighting or Chauvet ??? Thanks for your time
@haupts4ch3495 жыл бұрын
I know that you have the hex version but do you know if the color macros of the adj rgbw4c or also, your version are only usable with adj lights?