Very clever indeed. Congratulations on an elegant solution.

Here is an idea how about extending the shaft and adding a second coil wound in the opposite direction so there is power when it returns, like you see in a double acting hydraulic cylinder. That would be interesting to see.

In all realistic terms, the best uses I can think of are a jackhammer, vibration module, or subsonic sine wave generator on a speaker

Lidic Science I really enjoy your videos. Keep them coming!

You could make a continuously flowing pump if you enclose each magnet in a piston head, then sealed that in its own chamber. Both chambers would have 2 oppositely oriented Tesla one-way valves each; the inlet Tesla valves are connected to each other, and the outlet Tesla valves are connected to each other. That way, no matter which side is drawing in or expelling fluid, there's always pressure. The only moving part is the single double-sided piston because of the Tesla valves. The clacking sound & some of the vibration can be eliminated/minimized by adding some sort of bumper (a rubber washer?) between the coil and the piston heads.

What came to mind for an application was to simplify a sewing machine or a toroidal winding machine.

do not instal a coil in front of the magnet. Make the solonoid bifilar. one channel is connect to the battery and the switch. The other channel is the pick-up coil. You draw freely voltage off from the coil and store it in the capacitor. Now, you can eliminate the battery and run the hole thing on the capacitor. The battery is there for charging purpose.

I am mriganka...from India...seen almost of your all videos...I am studying Diploma in Electrical Engineering....and love this....you have made a great handcraft...but it can be used to make a electrically driven solenoid engine....

Nice! Put it vertically to use its own weight, with AC current.

Can you make good vacuum compressor using this

If you manually move that magnetized rod within the coil, it also produce electricity, right? Please make a video on that.

An interval marker or impulse metering device. As an alarm, it runs until current stops. Connected to a piezo, a sort of interval signal generator

Excellent video as I can use this project for another project I am making for a small sprayer. Excellent, this type of setup will work well in what I am making. A small amout of modifying and it will work nicely. Thanks for the help.

Good use of electronics and magnetism for teaching kids, well done, thanks

Where are you from iam from India.love your video's every time.

Many hours of fun, I can tell! What if you got rid of the switches and the extra magnet, and gave it 12V AC instead of DC?

I wonder if a hollow ferrite core would work if you wound the magnet wire on that [assuming the reciprocating magnets dont break the ferrite] ?

This is most interesting. I think you could make a clock using this principle. Thank you.

pretty neat reminds me of a cylinder and piston from combustion engine, I thought at first you were actually switching the polarity back and forth with some component. Do you think you can create enough compression make an engine similar to a piston driven combustion engine if that makes sense? replace the petroleum fuel with magnetic force? would that be feasible or would it just be a total pain in the ass?

This is very good explanation. Could you please advise- if we apply 12V with a larger magnets and/or more coil would the motor move slower? How could it be calculated? Many thx!

Hi this is cool... was thinking about two hand shake torches places on the ends of those arms

I really love this video. Thanks for sharing.

Perfect for stirling engine displacer

Nice experiment Sir 👍

bom trabalho. isso é também um botão de volume elétrico

nice!

Electric locomotive type vehicle, turning wheels and generator for battery? continued cycle? I wonder what kind of torque behind such motor for larger scale

He says that this is powered by the magnets on the end of the bar but when you actually buy one it moves the rod not the ends of the rod

Linear piston driver in a stirling heat pump

Thank you for these great info and knowledge you give ... i am following all your videos ... they are all great ... thanks 👍👍👍👍

Can you use small amount of the a.c voltage? And do this experiment ? With out 3rd magnet.

Can the rod reciprocating in about 20.000 times a second... It can be used as ultrasonic actuator then..

this motor can run a generator coil with less Lenz effect

interesting! i'm looking for a fine oscillating motor like this. This motor is fitted in an air conditioner cooled by a stirling engine and I have been searching for a suitable motor like this for a long time.

Hi I enjoy your videos. A question can you catch the back emp and feed it back to the battery? A boxer motor would be nice.

amazing! yes put a coil inside to have ac thanks

Excellent. Thank you.

nice information 👍

Hi! How mutch turn? What is the diameter of wire? Please ansver this questions. Thankyou.

It is very good for swinging a pendulum

But can it be used for propulsions? There is a n similar concept

Its amazing idea.

Really helpful content! 👌

Amazing 👍

And the switch has limited life.

saudações do Brasil a todos. interessante. aparelhos simples como esse nos fazem entender melhor como o electromagnetismo funciona. parabéns. sucesso.

Wow thats a ludic motor

Дружише, поставь геркон на разрыв питания соленоида - будет проще!

If I use a larger copper wire with less turns ; will it work ? Just curious!

Magnetic switch?

aplications : cofee machines , espreso more acurately , butchered one , and build up a car oil pump out of his linear motor :)

just for Jigsaw for woodworking :)

What's the material of your metal rod?

Why does the closeness of the switch affect the functioning of the coil?

I wonder why we don't have linear motor

da pra fazer um motor elétrico a impaquito

I love your videos but it's not a linear motor.

Bro can you make electromagnetic levitation

tHE rOOT mACHINE I lOVE iT

This may be used to build a reciprocating electrical engine. Can you build one please. By the way which country are u from. I am Indian.

Just make it biger, and thats a fap machine

Maybe scaling it up for a f"cking machine ?

As a two way switch??? 🤔

Good Demo by you? 🌹🌹🌹🌹🌹🌹🌹👍👍👍👍👍👍👍👍👍👍

Are you from USA???

Very good 👍👌

Hi ..what's the magnetic switch ?could u give us adjagram of its structure,please do..thanx

great

Nice !👍👍👍

Please check my smaller version, of this Linear Pulse motor with Back E.M.F demonstration People 🙏- kzfaq.info/get/bejne/g95yoZN0sLvUdnk.html .

Make a drsstc

piston

piston water pump

with AC it should be more powerful and does not need the last magnet nor sensor

Nice

lol, seems legit 🤣🤣

if you can... give to link buy magnetic switch...

Il à pas inventé le file à coupé le beurre 😅😅😅😅😅😅 un électro ordinaire 😅😅😅😅

i think this good for girl...😁😁

kzfaq.info/get/bejne/ndZoisplq9GqZXk.html puede usarse en este motor.

First

What is your biography, give on KZfaq and what's app contact, thanks for your feedback, I will wait for your feedback