Little Crow Gunworks-World's Finest Trimmer-2 (WFT-2) Overview and Trimming 223/5.56

Рет қаралды 9,171

2 жыл бұрын

In this video, I go over what the WFT-2 case trimmer is, what is included, how to adjust trimming length and switch bushings, as well as trim some brass. I also cover options that are available for the trimmer itself, and improvements made over the initial WFT version 1.
Check out the channel over on Utreon for unrestricted content and more detailed reloading content as well! All content is free for viewing, with subscriber support options available if you would like to support our work here on the channel!
utreon.com/c/TheReloadingCraft/
utreon.com/c/TheReloadingCraf...
Disclaimer 1: Handling of various reloading components and ammunition comes with inherent risk. Consult a reputable reloading manual for proper safety procedures, and do so at your own risk. The reloading craft and its members are not responsible for your safety, you are. The content contained herein is intended for entertainment purposes only.
Like & Subscribe Button animation courtesy of Graphics Expert on KZfaq. Used with Permission.
• KZfaq like subscribe...
#Utreon #HK #reloading #sinterfire #frangible #hecklerandkoch #CMMG #22LR #reloadingbench #hornady #lee_precision #redding #redding_reloading #dillonprecision #dillon_precision #lyman #frankford_arsenal #starrett #milwaukee #milwaukeetools #frankfordarsenal #rangeday #waltherarms

Пікірлер: 14

@badboytommy187 Жыл бұрын

That it is a good trimmer . But if you trim, so many different kind of shell light. 30r6 , 223 and 308 then you should get the one Frankford arsenal trimmer , that worked all .👌👍

@thereloadingcraft Жыл бұрын

I have tried the Frankford and the precision tolerance is nowhere close to the little crow gunworks setup.

@vikingslayer25 2 жыл бұрын

Great Vid. where can you get the carbide bits for this to upgrade please ?

@aubreyroche5080 2 жыл бұрын

I've been looking into it for a couple of weeks... Lot's of .223 Brass and trimming is not fun... Contemplating this on my Drill press..

@Jenni_Yimmi 11 ай бұрын

Do I still need to chamfer and deburr the case If I use wet media tumbling after trimming?

@thereloadingcraft 11 ай бұрын

It depends on how much material you’re removing, and how clean of a cut it leaves on the lip. I tried just tumbling to chamfer/deburr, but found it left a little ridge on the case mouth even after 3 hours with stainless media. Also seating the projectile was much smoother if I chamfered Vs if I didn’t.

@Jenni_Yimmi 11 ай бұрын

@thereloadingcraft look like the chamfer and deberr are mandatory. I am gonna use tri way cutter instead.

@thereloadingcraft 11 ай бұрын

Tri-cutter is definitely the fastest way to do it for sure

@johnzarollin2749 Жыл бұрын

A piece of plexi to shield you from small brass chips? What were you expecting 6" long dangerously sharp stainless curls? Pair of safety glasses is sufficient.. The cutting speed for that bit is better with the drill on high speed. The low speed torque is unnecessary and really noises. A quick and lighter touch will create less fatigue and give a clean cut to the cases..

@thereloadingcraft Жыл бұрын

The plexiglass is designed to keep the [very small] chips from flying all over the room. Usually this is done in the basement, or in another part of the house at the time, and cleaning up little brass shavings everywhere is a pain. I have since moved to a new location and have access to a proper workshop and a drill press, which makes for a much nicer trimming host. Check out the new video here -> How To Trim 223 Brass-World’s Finest Trimmer-2 (In a Drill Press) #shorts #reloading #reloadingbench kzfaq.infohNXNKpADMBc?feature=share