LSE90.com - HOLLEY Term X - BMW E90/E80 LS Swap Wiring Guide

LSE90.com - HOLLEY Term X - BMW E90/E80 LS Swap Wiring Guide - Make your Swap Run!

Рет қаралды 15,392

Күн бұрын

By popular demand we sit down with Mike at #lse90 www.lse90.com and have him walk us through the entire process the guys go through to wire a holley into the E90/E80 Chassis. If you're looking for the most comprehensive walk through on the internet, this is it.
00:00 - intro
01:26 - DME Wiring
11:30 - Holley Harness Modifications
17:15 - Installing Harness into Car
22:02 - Holley I/O overview
23:20 - Sloppy Mechanics Flex/alt harness
26:00 - Holley Transmission Harness
26:58 - Holley Main Power/Ground Harness
27:58 - LSE90 CAN Box
28:58 - Overview
Wiring information - lse90.com/documentation/lse90...
Sloppy Flex/Alt Harness - lse90.com/product/sloppy-mech...
CAN box - lse90.com/product/lse9x-holle...
Tessa Tape - amzn.to/3ypSIdP
Braided loom - amzn.to/3lyeV5O
Soldering Iron - amzn.to/37AJ1hb
Crimper used - amzn.to/3ip0Wxt
lse90.com/
www.hangmanperformance.com/
hangmanperf...
Common Terminator kits for the swap and GM Throttle body
Holley Terminator DBW with trans control - amzn.to/3ms9GmA
Holley Terminator DBW for manual trans - amzn.to/3uuPjs4
6 Pin GM DBW TB - amzn.to/2R4Ni7g
Split loom brand we use - amzn.to/2PGHxfN
Holley oil pan - amzn.to/2QqPyGf
FBODY ACCESSORIES
Fbody tensioner - amzn.to/3ezcFpV
Fbody Crank pulley - amzn.to/3ezcFpV
Fbody Water Pump - amzn.to/3uCcEYL
Fbody a/c compressor - amzn.to/3fX6deI
Fbody a/c manifold - amzn.to/3uy8wJ6
TRUCK ACCESSORIES
L99/Truck water pump - amzn.to/2QrGIIk
L99/Truck Tensioner - amzn.to/2S2dcZT
L99/Truck Crank Pulley - amzn.to/2PpqcYC
Starter - amzn.to/32QqfzR
FUEL COMPONENTS
fuel line kits - amzn.to/3fUj5Cx
6an - 3/8" Hardline adapter - amzn.to/3sbrlAe
walbro 450 pumps - amzn.to/3rWVUK6
Threaded IAT sensor - amzn.to/3dK9X0k
thermostat housing - amzn.to/39Xp4CL
T56 Slave adapter to AN - bit.ly/2PQx9lJ
TOOLS WE USE - LS SPECIFIC
Harmonic Balancer puller - amzn.to/3satEDU
Crane Cams Dual valvespring tool-LS1/2/6 - amzn.to/327TD4m
Fuel line disconnect - amzn.to/3d6Tpk2
Female Torx Sockets - amzn.to/322s7VQ
Everything filmed on this GoPro
gopro camera - amzn.to/3g166Px
External Mic - amzn.to/3d2eZGm
GoPro Mic Adapter - amzn.to/3dILsk4

Пікірлер: 56

@jasonjennings5833 2 жыл бұрын

Can’t wait for the next video. Keep banging them out.

@Louie88 Жыл бұрын

Amazing explanation! The best video I’ve ever seen. Detailed oriented and very informative and simply explained. I’m amazed. You Sir are very smart and a great teacher

@BrodieBro323 2 ай бұрын

Hell yeah! This is gonna be a lot of help with my next project. You, sir, are a lifesaver!

@ajtaylor889 Жыл бұрын

You are a blessing my dude

@EF9jdmhatch 2 жыл бұрын

This content is so damn good! I can’t wait to move forward with my swap again

@lonestardiyboyz6610 2 жыл бұрын

The 135 is turbo at about 300hp & 300 ft/lb torque while the 128 is naturally aspirated around 230hp

@DillonHoopes 2 жыл бұрын

Awesome video!! It is so helpful.

@MayCusp Ай бұрын

just started my 3 series this is the one i needed haha amazing thank you.

@lse90garage 4 күн бұрын

Happy to help!

@kevinshasteen5682 Жыл бұрын

Thx for your E90/E80 wiring vids. You and others, but mostly you have lightened the burden of wiring the LS swaps into these chassis. This isnt a complaint but only a suggestion. If you wanna keep making these swaps and be ahead of the competition, how much have you thought about being the first to popularise the F30, F80, and G20 LS/LT swaps. These cars are not as cheap as the E90's yet, but their prices are coming down; especially those that are mechanically totalled.., something to think about ;)

@joepaquette7435 2 жыл бұрын

Nice Job, detailed and clean. So easy a computer illiterate old man can do it........up to the tuning portion. Lol one step at a time.

@kevinshasteen5682 Жыл бұрын

Great stuff. Thx for taking the time to make your videos! Now that I've been politically correct and mindful of your "feelings".., we need the A/C video and another FAQ video ;)

@Bravadas10 2 жыл бұрын

Keep posting these videos. When you going to do an m3 engine mount kit.

@lse90garage 2 жыл бұрын

When someone gives us an M3 chassis to work with 😂

@frankhershman7253 2 жыл бұрын

stumbled on your video's while researching 335i swaps. Outstanding info, thank you. I've found a 2008 auto car with a bad motor but otherwise in terrific condition. Is using the stock BMW automatic over a T56 a good idea? I like the idea of reduced costs so I can put more money into a LS3.

@lse90garage 2 жыл бұрын

Stock bmw auto is trash, T56 far superior for the tq

@lsxbeambeam5201 2 жыл бұрын

We need one for the 5 series that’s the one everyone wants

@lse90garage 2 жыл бұрын

What’s covered in the video is identical for the 5 series. We’ve mentioned that several times.

@Speedaholic69 5 ай бұрын

Sweet! Exactly what I was hoping for. Picked up a 07 525i wanna swap

@ekytuning4449 2 жыл бұрын

hey, [USERNAME] Nice video! 🤩

@stephenj6139 4 ай бұрын

Love the video(s)! Where does the green wire on the main harness go? And for an auto does pin one (blue/black) need tied into the brake light(blue/red) /gray tran wire? And also for the automatic do the red and blue/red need to be connected to red and blue/red for tran can? I didn’t see that in the video but it’s on the website, maybe I missed it.

@lse90garage 4 ай бұрын

We have found it's better to use the 3rd brake light wire out of the frm for the transmission grey wire. Green wire on the main harness can be used to trigger a fuel pump relay if your rewire/delete the ekp

@stephenj6139 4 ай бұрын

Bro with the quick response! So green can be unused if I’m running n/an and stock pumps? And gray tran to Blue/red like the video shows? What about the red/blue to red/blue pt can? I’m close to done wiring but feel stuck/confused

@lse90garage 4 ай бұрын

@@stephenj6139 red and blue or can pair to the can box wiring. Don't use the blue red for the grey brake wire. It causes issues. Use the 3rd brake light wire out of the frm

@user-og5ri5rs7k 2 жыл бұрын

is it possible to retain the traction control?

@basscube5 Жыл бұрын

Hey! How are you triggering reverse in former automatic cars?

@2divinee431 2 жыл бұрын

Is the pin out different for a 2011 n55 e90?

@reetrarker9556 2 жыл бұрын

Do you have a build thread for the 1 series? Like the trans/motor combo and if you used the stock diff. Thanks again!

@lse90garage 2 жыл бұрын

We’ll be going over the build specs as we do more videos on the 1, but currently it’s a stock diff, stock bottom end 6.0, with a built 4l80e and circle d converter

@mrmeadowsiscool 2 жыл бұрын

Is this a 128 or 135? Is there differences with the two?

@ThaHammieJaassee 10 ай бұрын

how do we wire the pt can wires to your box if we're using the stock 5.3 ecu?

@lse90garage 10 ай бұрын

You don’t, the CAN box is for use with Holley only, currently is nothing available if you’re using a stock PCM.

@resinductelec Ай бұрын

I did this proceedure today. Three of the wires going by the color were off by one number where it was pinned. I chose to go by the color rather than the pin location. I hope that is right.

@lse90garage 17 күн бұрын

What’s your year and model? There have been instances where some chassis have things slightly diff but typically if you stick with the colors you should be ok.

@hectormagana6622 2 жыл бұрын

Those this all work with the 135i n55 engine ?

@lse90garage 2 жыл бұрын

The n55 wiring is slightly different but yes it will work

@DickHamm 2 жыл бұрын

First 🥰

@omarsyr3963 19 күн бұрын

What about the E60 5 Series? Has it been worked on before?

@lse90garage 17 күн бұрын

We have completed one, the wiring is very similar.

@SFGPUMP Жыл бұрын

Does it have to be the 6.0ls? Or could I use a 5.3?

@lse90garage Жыл бұрын

Any LS works, 4.8, 5.3, 5.7, 6.0, 6.2, LS7, LS9, 454 LSX, C5R block, dart block, doesn’t matter, they’re all the same physically.

@RickyLefleur 2 жыл бұрын

Do you have to use a Holley setup or could you use a factory ecu setup

@lse90garage 2 жыл бұрын

If you want to just run the engine you could, but you’ll have no way to configure anything to work with the BMW chassis like factory, plus by the time you spend the hours to modify the stock harness, buy a wideband, buy a boost controller if you’re going boosted, buy hp tuners so you can log it and make adjustments, and then pay for a tune, you could have just bought the Holley like we tell you to.

@RickyLefleur 2 жыл бұрын

@@lse90garage I was talking about a simple DBW/auto harness. And it would be for a N/a build. Also have all the access to hp tuners. The harness seems to come off with all the same lead/unterminated wires.

@lse90garage 2 жыл бұрын

@@RickyLefleur as we said above, you can do it, but the car won’t know it’s there and you’ll have no gauge setup or a/c control.

@solomang1 2 жыл бұрын

Lol stock ecu gtfo

@RickyLefleur 2 жыл бұрын

@@solomang1 my bad Ls god 🏆