Complete engine rebuild Restoration of a rusty engine. Can I rescue it to a perfect running condition . 3hp horizontal shaft briggs and stratton engine Thank you to my Patrons / daggerwin
Пікірлер: 1 200
@floopderpund4 жыл бұрын
i worked for Briggs & Stratton for 23 years. Thank You for doing justice to this motor. Great work!
@vasiliskara82882 жыл бұрын
hello I also have an engine I can not build
@skiprat19774 жыл бұрын
Them old Briggs & Stratton's are great
@mohabatkhanmalak11614 жыл бұрын
Have you ever run Honda and Subaru???
@stopglobalswarming4 жыл бұрын
Mohabat khan Malak yes, and it’s still great.
@jettramel4 жыл бұрын
I've done a few old Kohler's they held up well also, love seeing this restored.
@mr.abhishek81584 жыл бұрын
Which cars or bike engine is this
@cityslicker59814 жыл бұрын
I rebuild one for shop class and it had no hours on it like maybe 20 at most it's in great shape so I got a A+ on that
@StephenGoggin4 жыл бұрын
It's nice to finally see a small engine restoration done right. So many out there are re-using gaskets, not lapping valves, etc. Bravo sir.
@frank4vt4 жыл бұрын
My late father was a self taught small engine mechanic. I can’t tell you how many of these engines I have seen over the years. When you did the manual valve grinding, it brought a tear to my eye because I remember watching dad do that so many times. And to add to others comments, it’s an old Briggs, it’ll run! 😁Thank you so much for posting this!
@robertsymalla10713 жыл бұрын
same here bro :(
@theocrespin38952 жыл бұрын
On my own I have repaired engine like this last year It was a Bernard moteur
@user-tb9go1nn9m Жыл бұрын
@@robertsymalla1071 ざ
@daletesson46303 жыл бұрын
Just had a 1974 Briggs 5 HP break a connecting rod yesterday. I was thinking of replacing the engine, however, after watching this video, I'm going to press forward with a complete rebuild. This video is just the tutorial needed to proceed. Thanks for taking time to film your efforts. Good stuff!
@davidhall88744 жыл бұрын
Hell, that engine was in great shape to start with. The muffler hadn't rusted off and the tank had no holes!
@kevind31854 жыл бұрын
Looked like I had a a fresh plug in it before teardown.
@mattrzewnicki63434 жыл бұрын
Also looked to have a more modern style head gasket when it was torn down.
@holt72714 жыл бұрын
@@mattrzewnicki6343 it was..lol and i still havent figured out what parts was missing...maybe what ever it was hooked to...lol
@NVfrmDaO4 жыл бұрын
I'd have to agree, fresh plug and oil and sanding of the points it be going again
@JamesMiller-fm8qs4 жыл бұрын
@@holt7271 it was missing the Governor but I didn't see the bearing races for one anyway
@SlottedDiamond4 жыл бұрын
Man...you just took me back to my FFA small engines days...30 years ago. Surprised me that I was still able to follow along. Thank you.
@quicksilver72234 жыл бұрын
I’m took ffa small engine this year Btw we work on newer engines
@Mr_Tecumseh4 жыл бұрын
@@quicksilver7223 Probably because the OHV is more common now, but their are still millions of these L heads out in service and will be for some time. Very well built USA engines.
@jerrydewitt85854 жыл бұрын
FFA is the best to bad some schools don't give these opportunities anymore i feel it's backbone of education and of life. 50 years ago in my case best learning days of my life
@fordf150xltlariat94 жыл бұрын
His vids are quality, no music it’s almost asmr like great job like always
@MichaelTheRead4 жыл бұрын
"Almost"? It _is_ ASMR. And it's beautiful.
@josephamstutz91184 жыл бұрын
Im just wondering if those birds are real.
@jugheadjones54584 жыл бұрын
joseph amstutz if they were real some music would’ve been good to block them out. They were annoying. BTW I like birds.
@MrGuliton4 жыл бұрын
kzfaq.info/love/MrMVIBtqFW6O0-MWq26gqw
@twistedsister604 жыл бұрын
It's call restoration porn
@mcarroll5984 жыл бұрын
When I was in high school I took a small engine course. This is the type of engine we would work on in class. I ended up working on so many of these little engines. Ended up getting a job in a small engine shop for a few years. Love these little engines. Nice video!
@billschipper17184 жыл бұрын
I took a similar class in 9th grade
@petercarey71334 жыл бұрын
same, 6/7th grade metal shop class. still wrench'n these days, i'll always will be a gear head. b nice to have shop.
@david97834 жыл бұрын
One of the best courses I took in high school was small gasoline engine repair.That course has paid dividends all my life.I'm 65 now and still dabble with engines.Love it!!
@ChaotiX14 жыл бұрын
Same here, I took a course called Small Gas Engines as a freshman. That school also had a full auto body shop where people could get work done and students could learn the trade. unfortunately I moved away, and no other school I went to had any Shop courses. Still, loved the experience and now I do all the work on my car.
@djtaylorutube4 жыл бұрын
Similar. As a 14 year old, I used to buy old lawnmowers from the local auction and do them up. Then as a volunteer I would spend my weekends working at a preserved steam railway but I worked on the rail plant and machinery. Typically small engines for rail saws, rail drills etc. Then worked up to diesel locomotives all as a hobby before I met girls and figured they were more fun. Several decades later, when i'm working on cars here, although I could easily afford to pay someone else to do the work, my neighbours will ask "Why are you doing that, why don't you just pay someone else to do it?". My response is simple "Because I can."
@D35T1LL3R4 жыл бұрын
This is sooo much better than these asian fake restoration videos.
@GrandsonofKong4 жыл бұрын
I know...and you never see it run after "restored"!!! Just click bait
@mr.slaphappy37944 жыл бұрын
Jesus I watched one of them "restore" an old gearbox sort of thing, he didn't even bother scraping all the loose rust of (let alone remove it) and literally just slapped a load of filler on the thing!! I stopped watching that video from the second I saw him do that.
@filip60394 жыл бұрын
D35T1LL3R 👍🏻
@christians.87394 жыл бұрын
I read this too quickly and thought what in the world do fake Asian restaurants look like inside?!
@BrodyBaddis4 жыл бұрын
Christian S. restoration, is why. I too, read it as restaurant.
@synthiccl4 жыл бұрын
is it just me, or do I have a strange addiction for watching engine rebuilds, start ups, and restorations?
@minime2454 жыл бұрын
i also have an addiction to watching these
@rayburnett32534 жыл бұрын
@@minime245 ,I too love watching them. I have been knowing how to do small engine work for about 20 years now. A friend of mine got me interested in Briggs and Stratton engines
@paultickner23 жыл бұрын
Nope I also find it addictive
@jamesrichardson7714 ай бұрын
I'm addicted too 😜
@mn_steelyboi6484 жыл бұрын
Anybody else start this video, and say to themselves, “It’s an old Briggs, it’ll run.”?
@thesilentone40244 жыл бұрын
I thought they billed good shit back then it will start good luck killing that
@andrewstrainstuff17734 жыл бұрын
How will old Briggs not run? Even if it was underground buried for 10 years it will run. They built them so good they can't be destroyed. It's just that good
@thesilentone40244 жыл бұрын
@@andrewstrainstuff1773 lol with ya there
@omfgallusersaretaken4 жыл бұрын
Soon as I saw the sticker im like yeah that's got another 200 years left in it
@andrewstrainstuff17734 жыл бұрын
@@omfgallusersaretaken u right u right
@stefanbekan12984 жыл бұрын
3 videos in a day, what have we done to deserve this.
@nationaljonahgraphic4 жыл бұрын
Does anyone else find this restoration extremely satisfying and relaxing??
@fredscheerle7592Ай бұрын
Yes, but it can be difficult when previous owners have replaced key parts ie the engine covers , Dam weekend Mechanics and there tinkering
@cameronerickson78693 жыл бұрын
Its like art and mechanics combined, all a man needs is his shop, some peace and quiet and the sound of tools working. Puts me at ease👍👍👍👍
@jackblacker60994 жыл бұрын
I love just watching this videos with no music or talking just listening to the birds chirping.... it’s nice cuz it’s the depressing part of winter here in Canada and it’s too cold for any chirpy birds
@snazzy2264 жыл бұрын
Jack Blacker Canada let’s goooo 🇨🇦
@simonpotter75344 жыл бұрын
That was a thing of beauty watching you restore that engine, excellent job.
@Ellenslife8514 жыл бұрын
Another top notch restoration. Can’t wait to see more on that commercial walk behind mower that you got that would be cool to see that one all done I know it’s gonna look really good
@mooseguyableАй бұрын
Found you in the back, covered in dust and rust, A relic of the past, a memory we almost lost, With a heart of steel and stories untold, Time to bring you back, give you life, let’s be bold.
@beachthor12 ай бұрын
That diaphragm carb is a hallmark of old school engines. Great work
@xccxvindaloo4 жыл бұрын
Nice to see someone lapping in the valves manually, so many done with drills and air tools now. I used to do them like this (old school) and it was my favourite part in a rebuild/repair job. 👍
@ghostfire3194 жыл бұрын
That is the engine I learned to work on. They are probably the simplest and easiest you could ever build. Great for a young person wanting to learn.
@LanceHanlonOutdoors4 жыл бұрын
You hardly pulled the cord and it was running... Great rebuild... You definitely have a gift.
@jeffplant32 ай бұрын
Well done. Nice tear down, recondition, paint, assembly and set up. These engines were ubiquitous. Great job
@pigface4724 жыл бұрын
This was the first engine I ever worked on, found it abandoned in a field, I was so proud and happy when I got it to run.
@mr.abhishek81584 жыл бұрын
Which vehicle's engine is this
@CaRrOtCaKe322004 жыл бұрын
I had a motor like that on a mini bike i road it everywhere for years. Two pulls max and it would start. Them motors were great. Gave a kid lots of entertainment.
@nighthawkj30A44 жыл бұрын
Im Tecumseh engine owner but this Brigs and Stratton engine video was excellent and relaxing.
@ianewers98413 жыл бұрын
As we in England are led to believe, some Americans say "fire that sucker up Dude" Well done!! Proper vid. Many thanks.
@karolis13974 жыл бұрын
Am I the only one who can smell that running?
@tristankincaid72374 жыл бұрын
Karolis 1 I can too. Recently got an ‘85 briggs running and it smells great. Model 130252.
@ChaotiX14 жыл бұрын
Smells like Exhaust and America.
@vx-iidu4 жыл бұрын
@@ChaotiX1 America smells like farts
@Hankbob_Hillpants4 жыл бұрын
This is the most love I’ve ever seen a 3 horse Briggs get
@TheThomasites3 жыл бұрын
My snowblower has a BnS engine and is older than me. Still runs great, has been rebuilt twice in its 50 year life, so far.
@timallen60253 жыл бұрын
Yay, thank you . Just been given one of these attached to a 1960s tiller. Now I can sort the carb and points . Your video is faultless , thank you !
@wolfgangholtzclaw26374 жыл бұрын
I studied small engine mechanics fifty years ago, I took my dad's old briggs and stratton lawn mower to school and rebuilt it. I still remember it. Two types were common the Horizontal as scene here and even more popular the vertical shaft. They ran and ran.
@breadbaker4 жыл бұрын
"The engine cover also needs sandblasting" me: yay!
@TravisFabel4 жыл бұрын
I was a little annoyed he didn't blast the engine case. It would have cleaned up nicely
@Chris-yy7qc4 жыл бұрын
So satisfying
@TheXev4 жыл бұрын
@@TravisFabel It may have just been a bit of extra precaution to avoid getting sand into the internals.
@infamousgamer56074 жыл бұрын
The old Briggs engines almost never die unless you absolutely need like them and put no oil in them.
@YUHJKT4 жыл бұрын
I loved that video. Back in the 1960's we had a Briggs & Stratton powered lawn mower and even as a kid I realized that that thing would never quit. Excellent job on the video and mechanics. Very enjoyable.
@rayj.29504 жыл бұрын
You restoring these mowers and engines makes it look like and run like it’s fresh out of the factory
@MJ-nl3pv4 жыл бұрын
Your Video by far the best and right way to due a rebuild and it was relaxing watching.
@geraldolmstead13354 жыл бұрын
This restoration sets the standard
@edgufler11224 жыл бұрын
Wow !! Unbelievable Restoration. You did a awesome job on it. These engines are the best around . This one will last 20 more years. Thank you very much for the video. I enjoyed it.
@mj-mr5yu7 ай бұрын
Others have said it also but, i dont think ive ever seen one of this generation briggs engines worn out, and i have been around them a lot, mostly its just carb issues, new carb kit and its away again. You did a top class job of restoring that engine sir, 👍👍
@v-g-z36894 жыл бұрын
Dang, the further I got into the video, the more surprised and impressed I was with the quality of that rebuild. I have to admit, my expectations were very low ;) Just a little bit of advice there is I can give you: when lapping in the valves, do an actual fluid leak test. I was surprised how a visually perfectly lapped valve was still leaking, and an other one who looked exactly the same didn´t. That will give you some extra compression, and with these kind of engines, every bit is desperately needed. You might have done it, but in case you didn´t: check the valve clearence when the valves are lapped in and grind down the valve ends carefully. A tiny bit too much clearence is better than a tiny bit too little. Thirdly, mill the surfaces between the cylindre head an the block with wet fine grit sandpaper on an even plate (e.g. glass). I was surprised how uneven those usually are! Also: check for air leaks in the intake system by spraying some brakecleaner on certain spots with gaskets while the engine is running at idle speed. If it slowes down or speeds up, there is a leak. You might have done these things off camera, but if you haven´t, they really improve engine performance significantly and most of the time you only realize it afert you have the comparison! Great work overall, keep it up!
@christinewaite82364 жыл бұрын
You really make a great job at restoring.i think I need to buy one of your quality restoration's.
@cen7ury4 жыл бұрын
Excellent work, my friend! You really brought that motor back to life! Seeing this has inspired me to get back to work on my projects that I've been ignoring. Thank you, sir!
@mrbookends4 жыл бұрын
I have so much work to do today and this just ate up 30 min of my time. Sooooooooooooo satisfying to watch! Subscribed!
@indyzmike4 жыл бұрын
Your engine is missing the spacer that goes on the bolt between the engine base and the gas tank mounting bracket. The spacer is is like a bushing and is about a half an inch long. This will square up the gas tank to the engine like it should be. Great restoration, looks awesome!!!
@jakobkopp90664 жыл бұрын
I have a few of those motors and none of them have it?
@melvinhernandez50744 жыл бұрын
You. can. make. a. lot of money. from. yur. house. American. water. work. did. this. on. 1970. they. became. nation. wide. let's. MAKE AMERICA GREAT AGAIN
@jessemarchese72454 жыл бұрын
@@melvinhernandez5074 ?
@makern53044 жыл бұрын
@@jessemarchese7245 he had too much meth
@Shadow-eo2pf4 жыл бұрын
Nothing beats these engines, I at least have 3 of them now, like to add more to the collection but brigs flatheads are just awesome
@makeitbetter96854 жыл бұрын
Thing of beauty! Brought a tear to my eye.
@kjell-richardlvdal3734 жыл бұрын
that is a real old motor, oversized bolts so it is easy to unscrew tha bolts, and solid dimension in all parts, this is built to last a lifetime THIS IS THE BEST VIDEO ON KZfaq ON HOW TO RESTORE A MOTOR, VERY GOOD FILMING WITH ACCURATE TEXT UNDER
@RobertsVintageGardenTractors4 жыл бұрын
I have one of those sitting in my garage right now.
@tractorboy41484 жыл бұрын
Great video Daggerwin !
@joehartley064 жыл бұрын
The video has only just come out so how do you know it's a great vid 😉
@tractorboy41484 жыл бұрын
@@joehartley06 Because Daggerwin made the video, i know its going to be good
@joehartley064 жыл бұрын
@@tractorboy4148 good answer
@abjlilzad30154 жыл бұрын
Tes great vidéo
@richcampoverde4 жыл бұрын
At last a channel on youtube that is dear to my heart. Motor mechanics love it you have a new subscriber
@alfries97363 жыл бұрын
You covered it all. That start-up was flawless my friend. Love the powder coatings as well as using the finest assembly lube !!!
@elirenigar93574 жыл бұрын
I’ve never seen someone handle a Briggs so delicately 😂
@greemstrider4 жыл бұрын
That flywheel came off so easily??? O.O Each time i have to take one of these off i need to heat it up and pry it off with such force! Lucky!!!
@charlienorton23374 жыл бұрын
GrimStrider don’t heat a flywheel!! All you need to do it put a piece of wood over the shaft, pry up on the flywheel and hit the wood
@greemstrider4 жыл бұрын
@@charlienorton2337 mmmm you mean.... pry it from one side and just hit the wood piece lying on top?
@charlienorton23374 жыл бұрын
GrimStrider yep
@derofromdown-under28324 жыл бұрын
An excellent rebuild. Love the powder coating finish... WELL DONE!!! 10/10
@davidditman82064 жыл бұрын
Simply a wonderful video. Helps my 9 year old and myself learn so much
@threaded4mypleasure8184 жыл бұрын
I had that same one on an old late 70s tiller. Something Bird. I cant remember. I think Montgomery Wards. It was a great little motor. Those carb screws that thread into the head are a pistol to tighten.
@melvinhernandez50744 жыл бұрын
American Organics. this. is. why. let's. MAKE. AMERICA. GREAT. AGAIN. WE. CAN. DO. THIS.
@desertbob68354 жыл бұрын
@@melvinhernandez5074 Not with the orange Thief in Chief in there, we can't.
@WindinyourSails4 жыл бұрын
purring like a kitten. Excellent job, well done.
@souloukex66804 жыл бұрын
Excellent. No music, no bla bla, not waste of time, ff were it needed to be
@Brax27004 жыл бұрын
In school I had to fully take apart a 3hp Briggs just like this, it was obviously newer but it’s interesting to see that not much has changed since 79!
@phenylxeon4 жыл бұрын
Oh my god we have the exact same engine we had it sitting in a garage for YEARS and it was in a like sidewalk weed trimmer thing and it still runs perfect as new to this day i had no idea it was That old oh well that some serious quality right there
@XBullitt16X4 жыл бұрын
The old briggs engines were relaible as hell, built to last a lifetime. Sad to say they aren't like that anymore, it's cliche saying but it's a true one, they don't build em like they used to.
@Walkercolt14 жыл бұрын
Actually, there's no quality to the aluminum bore engines at all. They are CHEAP! Cheap to build, cheap to buy, cheap to work-on, cheap to replace. An iron linered one is different. An IRON-BLOCK is real quality. An iron-block will be running for your great-grand-kids if you keep oil in it. I have an 11 HP vertical B&S from 1940's on an air compressor. Loose rope start. One part pull to get it past TDC, then pull with the choke on and it'll usually start. Second pull with the choke off, it starts everytime. Oil-bath air filter, gravity feed carb below fuel tank, 10+ years older than me. Uses about an ounce of oil per tank of gas, like it did when it was new.
@monster119754 жыл бұрын
When you're deep in a youtube hole, hear birds chirpin in the video and realize its 6 am
@Klaatu-ij9uz3 жыл бұрын
The proper tools (and know-how) are everything!! One VERY enjoyable video!!
@tkskagen4 жыл бұрын
I know that I said it before, but it is sure nice to see people actually take care of our Engines! -PROPERLY...😎
@Zeppelinlv20074 жыл бұрын
More enjoyable than chrisfix's videos. Yeah, I said it. Fight me.
@pro-impulse28314 жыл бұрын
Zepper2019 I will
@nicolasgarcia4084 жыл бұрын
You disgust me
@kickinwinghotboi8834 жыл бұрын
Both channels have excellent content. But you can't say one channel is better than the other (well, I guess you could given the fact that you are just voicing your opinion). They are on totally different spectrums and offer different content (in a way.. kinda)
@TravisFabel4 жыл бұрын
Totally different kinds of videos. Lol. If you want to mix between the two look at Mustie1
@breezetix4 жыл бұрын
27:15 wow that was easy
@tombarlow61763 жыл бұрын
Beautiful restoration of an old Briggs
@killerchopsdempster274 жыл бұрын
These particular engines are the best. The ones we rebuilt in high school were gold, but identical to the one here. Nice and simple to fix anything on really.
@mr.slaphappy37944 жыл бұрын
First pull look at that!!
@carlnewman244 жыл бұрын
I have never had a B&S flywheel come off like that ! and why leave the rubber hose attached to the Valve Spring cover? Paint Stripper is gonna eat it !
@Mr_Tecumseh4 жыл бұрын
@@carlnewman24 Clutch was missing, flywheel was loose on shaft.
@dannynewton75474 жыл бұрын
Project Farm be like, "will Quaker oats increase the compression of this engine? Let's find out."
@rodrigo108014 жыл бұрын
great video, just the sound of work, glad to view that valve sits hand made on the old way, thanks for sharing.
@Porkpickle3 жыл бұрын
This video is handy because i started rebuilding the same engine just an older version. Very helpful for reference
@camron52744 жыл бұрын
9:12 "noice."
@MichaelHenderson593 жыл бұрын
Underrated comment I love that!
@sam._.buswell81814 жыл бұрын
Don’t forget after running it in change the oil after the first 2hours or so
@HavokTheorem4 жыл бұрын
Why?
@user-do6qr9rm3l4 жыл бұрын
real restoration, very professional!
@superdave548114 жыл бұрын
So refreshing to watch a video and not hear annoying music. Thanks for posting this work of art.
@GillesYT4 жыл бұрын
Hey, i have a very similar engine at home! :P I think it was a 4HP though. Still runs okay, but i wish i had the tools and knowledge to give it that kind of facelift ^^
@billbkr32ify4 жыл бұрын
Unless it has sentimental value don't waste your money doing what he did. Unless you are okay with knowing it will not be worth anything when done other than your enjoyment
@afzaalkhan.m4 жыл бұрын
Excellent. No nonsense talk makes it better. Thank you .
@Atr42Greasemonkey4 жыл бұрын
I love your videos no music no talking just a mechanic doing his thing .
@stefanglarsson-fritz65444 жыл бұрын
Excellent! Video helped me alot today when I was fixing up a 130212-0819 engine from 1978. Went from completely dead to ALIVE!
@bobbaleno48944 жыл бұрын
this brings me back to high school 79-80 small engine repair class. they had bins of parts aone bin was blocks and others were pistons and cams etc. .and my project was to build an engine. it was the best, mostly because there wasn't much reading, it introduces me to parts washers and wire wheels and lapping tools. then I transferred from that school to go into computers. I like watching these videos and living vicariously though them. Thanks for the memories
@mjg2634 жыл бұрын
What a wonderful vid, thanks very much! I once had the same engine (mine came from an Atlas roto-tiller) that I rebuilt in the same way years ago. I sand blasted it and sprayed it back to it's original Atlas orange color (block and all) and it looked pretty good but boy that powder coat process that you did on that one really takes it to the next level! Beautiful rebuild, really takes me back!
@desertbob68354 жыл бұрын
I have the same model, but from 1964. It has fresh rings, seals and gaskets and lapped valves. It runs as well as new in 2020. With proper care and use, these early aluminum engines will outlive those who bought them new. They are well-designed machines. This chap's paint work beat mine by a furlong, though. Excellent job.
@erelove12844 жыл бұрын
I enjoyed watching a master doing fantastic job on Briggs. I would love to learn the skill before getting old.
@ninney7944 жыл бұрын
Used to love building/modifying these when I was younger to run on go karts. I always used the 5hp but did use some 3hp parts.
@scroungasworkshop46634 жыл бұрын
I have to say I really like your editing, your short segments show enough for people work out what you are doing but not so much that it gets boring. The finished motor came out really well. Thoroughly enjoyed your video. Cheers Stuart 🇦🇺
@Coolsweat674 жыл бұрын
40 year's and still running,Australia is watching
@fredscott4134 жыл бұрын
Just beautiful restore,thanks for another one.
@michaelmaurer85774 жыл бұрын
THANK YOU SOOO MUCH! I'VE LEARNED SO MUCH ABOUT HOW ENGINES FUNCTION FROM VIDEOS LIKE THIS ONE!
@fastpost50684 жыл бұрын
One of the best videos on KZfaq!!! Excellent Job!!!
@screwsnutsandbolts4 жыл бұрын
Awesome job and great video ! 👍🏻
@Sandler234 жыл бұрын
started on first pull. amazing!
@mikecorrado49712 ай бұрын
Sweet rebuild! Thanks!
@david97834 жыл бұрын
Masterful job! Thanks for sharing.
@lotusphere64 жыл бұрын
This was my first go cart engine. Many thanks. Keep up the good work!
@raa20052 жыл бұрын
Same here; still have it and it looks exactly like the engine before restoration; 3 HP good and powerful little engine; go cart went 35 MPH
@ann-marieinkpen66823 жыл бұрын
That was mesmerizing. Learned a few things along the way.
@nikolaosnikolakakis78544 жыл бұрын
Best ever restoration video i have ever seen!!! Great detailed job step by step. Very quality job!!!
@rcas350pilot82 жыл бұрын
Someone gave me a 5 hp made in 1976. They said it hadn't been started in years. Put in about half inch of gas, cleaned plug with rag, pulled out choke and it started on third pull. Not even any smoke on startup, runs smooth as silk.
@boboala14 жыл бұрын
This was a great restore video! Like music to my eyes & mechanical ability level as of now! My 1st time seeing how valve lapping was done - I can do that! Inspiring!