No video

Maddog GY6 150 Gets Rear Gear Set and goes 70 MPH!

  Рет қаралды 10,093

Mini Me

Mini Me

Күн бұрын

This gear set will NOT give you 70mph. it will probably make a stock GY6 slower. I have 171 Kit, Cam, 28mm Carb etc to support this gearing.

Пікірлер: 55
@Valentine98766
@Valentine98766 Ай бұрын
Dang you really know your stuffs Inspirational! Like a damn sermon You Preachin' on here
@randyalmonte1431
@randyalmonte1431 9 ай бұрын
I’m about to do the same to my Maddog scooter. Thanks for the info dude very helpful.
@user-vl2lz9fk9y
@user-vl2lz9fk9y 3 күн бұрын
Good video i based my decision on this video. Went with 15/37. Find out next week.
@GhettoWrench
@GhettoWrench 2 күн бұрын
@@user-vl2lz9fk9y cool. Hope it gets you speed.
@flintstone4208
@flintstone4208 8 күн бұрын
Just got a new GY6 150cc scooter and unless the speedometer is off it does everything on the speedometer and a little more if going down a slight decline and it has 120km/h on the speedometer that's a little over 74mph and that's stock
@GhettoWrench
@GhettoWrench 7 күн бұрын
@flintstone4208 chinese speedos are generally way off. Use your phone to do a speed check. If it is a digital speedo, you can usually calibrate it and there are good youtube how to videos. When my wife's real vespa says 72mph and the GPS says 64mph.
@speedymillz6675
@speedymillz6675 24 күн бұрын
Ok this is fuckin awesome!! Just bought a ruckus with a stock gy6 150cc. I plan to do a 171 cc big bore kit because i daily this thing and i need to be able to produce 60 mph for higway riding. Would you suggest doing the gearing next like in your video or should i just slap a cvt transmission kit from wrolling wrench?
@speedymillz6675
@speedymillz6675 24 күн бұрын
also does a 842 belt really make that much of a difference?
@GhettoWrench
@GhettoWrench 24 күн бұрын
@speedymillz6675 watch my CVT kits are a scam video. Your next gear up step is a 115mm variator. Test that then add a 842 belt and test that. With a 150, you may or may not be Faster with both and have to go back to the 835 belt. Run that until you get a big bore prob. You need a lot of power to make a rear end gear set give you more speed. Personally I liked the bike better without the gear up kit and doing 68mph as it was a lot quicker to get there.
@spikonn
@spikonn Ай бұрын
What Gear you suggest for 63mm bore kit with 4V and +8.2mm crankshaft ? Thank you !
@GhettoWrench
@GhettoWrench Ай бұрын
I have no idea. Have to know what RPM you are currently running and then know what RPM you want to be at. From there you can figure out the percent of increase you need.
@spikonn
@spikonn Ай бұрын
@@GhettoWrench I have 30mm Carb and I keep the RPM at 1900 - 2000 since that everyone recommends to keep it at that number.
@GhettoWrench
@GhettoWrench Ай бұрын
@spikonn I mean at full speed. What RPM? If you are not above 9000 RPM I doubt the gear up kit will make you faster
@GhettoWrench
@GhettoWrench Ай бұрын
@@spikonn This one prob explains it better: kzfaq.info/get/bejne/etlhe6uZ3pObkXk.htmlsi=ob3eVfpzACJvHTM1
@litobayabo5749
@litobayabo5749 3 ай бұрын
What gear set needed for a 125cc gy6
@GhettoWrench
@GhettoWrench 3 ай бұрын
I would not think any. No clue what's in there stock. Are you hitting redline? 9500 RPM. If so, do you already have a larger variator? That is the first gear up mod I would try.
@earlisfayette9061
@earlisfayette9061 7 ай бұрын
Ok I pretty much feel for the gimmick as u call it I spent right at 800$ with the dorbyworks Ankle biter kit with the ncy super Trans kit 2000 rpm contra spring and I got the rolling wrench gear up kit after install I whent from a factory top speed of 63 mph to 54 max after install was very pissed I put factory spring back in and now I can do 60 but I have to tuck down to get their so I guess my question is what all do u have down to achieve 70mph could really use some advice thanks in advance
@GhettoWrench
@GhettoWrench 7 ай бұрын
You have geared that thing very tall with the gear kit and large variator. Imagine being on the highest gear on your bicycle. Your legs are not strong enough to pedal and go fast. I would imagine your RPMs are low (6000 to 7000) as you bike is struggling with that high gear. What have you done to the motor power wise to push that that high gearing? I have a 171 kit, Cam and 28mm PWK. I also used the (smallest amount) gear up kit.
@earlisfayette9061
@earlisfayette9061 7 ай бұрын
@@GhettoWrench I have the 150cc upgrade from cajun maddogs 26mm carburetor ,ncy ignition coil ,ncy cdi box that's it besides the Trans and cvt
@GhettoWrench
@GhettoWrench 7 ай бұрын
@earlisfayette9061 so the NCY CDI is actually slower than the stock. I have videos proving that. The coil makes no difference on power. We don't have enough compression mods to need a bigger or hotter spark so spark is spark. The 26mm carb is an upgrade, but to what? You need a reason to need more fuel. More displacement or more RPMs or cam etc. Do an electric fuel pump and re-tune your carb, and you will notice a big difference. You may try putting the stock CDI back on and seeing which one you like better also. What RPMs are you running wide open?
@earlisfayette9061
@earlisfayette9061 7 ай бұрын
@@GhettoWrench 7000 rpm max
@earlisfayette9061
@earlisfayette9061 7 ай бұрын
@@GhettoWrench I was planing to order the electronic fuel pump and pulse from rollingwrench and a afr gage and a 172 big bore kit with cam and slide carb
@kaddymorgan1625
@kaddymorgan1625 Ай бұрын
I dont use that sprocket and my scooter go up than 118km. So what's the benefits?
@GhettoWrench
@GhettoWrench Ай бұрын
@@kaddymorgan1625 prob just lower RPM and better gas mileage. I am not a fan of the gear rear drives on maddogs. They are already geared up with their big wheels
@lyleledford-hr3br
@lyleledford-hr3br 2 ай бұрын
How fast does a typical mad dog? 150GY6 motor scooter go.
@GhettoWrench
@GhettoWrench 2 ай бұрын
Stock goes about 50mph. You can follow these videos and see what it takes to go faster. The free mods are probably the best. kzfaq.info/get/bejne/ar6TapiEzdTVc3k.htmlsi=Xj0yvy9Dta2KowoQ
@raso_i
@raso_i 3 ай бұрын
15:55 everything reminds me of her...
@GhettoWrench
@GhettoWrench 3 ай бұрын
😆😆
@dons.hacchh
@dons.hacchh 12 күн бұрын
What cam and roller weights were used on this run?
@GhettoWrench
@GhettoWrench 12 күн бұрын
@dons.hacchh Taida T100 Cam and 14g rollers in a 115mm variator
@user-vl2lz9fk9y
@user-vl2lz9fk9y 3 күн бұрын
​@@GhettoWrenchso I'm putting in a 15/37 gear it was a pain in the ass to figure out I asked a few that did gearing no response. So I just went with 15/37. 🤔🤔
@GhettoWrench
@GhettoWrench 2 күн бұрын
@user-vl2lz9fk9y worth a try though.
@stewartrhaines
@stewartrhaines 9 ай бұрын
Nice! What app are you using for your runs?
@GhettoWrench
@GhettoWrench 9 ай бұрын
This one, bit I hear it is not working for download now play.google.com/store/apps/details?id=com.milejko.dragracer
@BIGSMOKE-bl2lq
@BIGSMOKE-bl2lq 9 ай бұрын
No idea why this was recommended but i pissed myself at the start THIS IS GONNA GET SERIOUS hahahaha yea on fucking china 150 lol
@GhettoWrench
@GhettoWrench 9 ай бұрын
@BIGSMOKE-bl2lq ya these things are slow AF. My wife's moped is still faster. LOL
@stewartrhaines
@stewartrhaines 8 ай бұрын
@tedowen409 Yea, it looks like it's for an older version of Android damn! Thanks though!
@SHARKPAPARRAZZI
@SHARKPAPARRAZZI 8 ай бұрын
I want to know too
@lastresort1757
@lastresort1757 3 ай бұрын
Damn and this is a fully stock 150cc?
@GhettoWrench
@GhettoWrench 3 ай бұрын
Not even. Look at other videos. Big Bore kit, Cam, 28mm PWK, big valve head etc .
@JonahNAloha
@JonahNAloha 4 ай бұрын
What gear do I need for a gy6 50cc? Lmk need for speed and torque.
@GhettoWrench
@GhettoWrench 4 ай бұрын
Well gear down will give you torque and going up will give you speed, but only if you can currently hit redline. Every bike is going to be different. You would just have to try some. I have not tried gear changing a 50 yet
@frednetherlands887
@frednetherlands887 2 ай бұрын
Which app are you using? Thank you.
@GhettoWrench
@GhettoWrench 2 ай бұрын
Called "Drag Racer" but the link is dead. Which is nice cause no ads.
@JonahNAloha
@JonahNAloha 24 күн бұрын
Just wondering if anyone knows how to get a gy6 50cc to do at-lease 50mph with stock parts and some free modifications? Lmk guys what’s the top speed I can get from a stock 50cc? Porting? Carb? Exhaust, valve lash? Electronics?
@mccdub305
@mccdub305 20 күн бұрын
Do a 150 swap
@user-vl2lz9fk9y
@user-vl2lz9fk9y 2 күн бұрын
Don't ask 49cc scoot, or rolling wrench. IV seen a lot of videos on KZfaq.
@king0dasouf
@king0dasouf 5 ай бұрын
I tried it Went slower Ima big dude though
@GhettoWrench
@GhettoWrench 5 ай бұрын
My buddy just went back to stock gears and went faster too. I have the very mildest gear up kit tho... only 14%. He had one of those more normal 20+% ones.
@rodgercgreen411
@rodgercgreen411 5 ай бұрын
It's a moped not a motorcycle you want motorcycle power go by motorcycle you want to get around town cheap go get a scooter
@GhettoWrench
@GhettoWrench 5 ай бұрын
LMAO. I actually have a pretty solid background in built liter race bikes. You are correct tho. It's Def a moped.. just with the plastics off. Most my posts say scooter. I'm old and prob got confused.
UNO!
00:18
БРУНО
Рет қаралды 5 МЛН
а ты любишь париться?
00:41
KATYA KLON LIFE
Рет қаралды 3,5 МЛН
INSTALLING A 171CC 61MM BIG BORE ON YOUR GY6 W/ TORQUE SPECS
27:17
The Ruck Shop
Рет қаралды 185 М.
How practical is a Ruckus/Chuckus 150cc GY6 ?
9:04
HyperDash Garage
Рет қаралды 10 М.
150cc GY6 Go Kart CVT Upgrade & Swing Arm Bushings
17:22
Red Beard's Garage
Рет қаралды 120 М.
232cc GY6 TURBO HONDA RUCKUS 🔴 LIVE EDIT
26:19
Rolling Wrench
Рет қаралды 69 М.
Customer States 'My Boyfriend Fixed My Brakes!!!'
12:35
Mechanical Nightmare
Рет қаралды 48 М.
Common GY6 Engine Problems and Troubleshooting
8:51
Kyle Crowder
Рет қаралды 368 М.
How to make a GY6 faster - FINAL DRIVE GEARS (EPISODE 3)
11:32
Rolling Wrench
Рет қаралды 127 М.
UNO!
00:18
БРУНО
Рет қаралды 5 МЛН