Me too. That was some next level thinking.

Same here. I'm makes one of those jigs.

What tool did he use?

​@@rojinadhungel7376tool post! See 4:47 onwards

That's actually a pretty old trick that still works. lots of people forgot about it.

Thanks! 🙂

@@MadeinPolandChannel di

​@@MadeinPolandChannel ❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤m

P000000000000000000000000

What do you base that oppinion on?

@@shokatali5126 7⁷⁷⁷

I love this video but using spoons in order to mow is a bad idea the quality of cut is poor this tools is done to be but on an arm in order to clean bush or mowwe some tinny woods. I do not like this tool farmer destroy all neest and birds with because they use it at spring. To cut grass use a disc with finger/ flying Cutter or a reciprocal barre the cut us perfect and you do not kill bugs and other life's in your field.

Да чтоты ,чёрт побери, несёшь?!​@@sudrienet

🕉

A 20 hp tractor can drive a 5 foot flail mower quite ok, we used to run ours through 3 and 4 inch shelterbelt trimmings, one pass, done

❤

Safety third

Eikä turhaa loputonta selittelyä kuten amerikkalaisia videoissa on tapana tehdä 😂

Can just imagine a GIANT front mounted flail mower, mulching the zombies!

made in USSR

The flail mower is very common in my area. Does a much better job that a regular bush hog since it leaves very small pieces in its wake.

Что-то не очень молотки работают, я ждал что чистая земля останется. Работа класс!

could use some sommercial blades that are easy to replace and could do with some sharpening

b. .. , . 8pick MP3

Good Luck 🙂

@@MadeinPolandChannel Thanks broski 👌

Yes belts too short but mainly they need to have a spring tensioner on them. Mine has that and without it, many things can break.

Not a great work i'm affraid... While working, you can see the whole thing shaking... So it's pretty bad... The shaft is off center...

only point of sure fail is the welded drive shaft at 18:15 it will snap like glass there

Thanks Vilson 🙂

.....putting boilermakers in with fabricators is a stretch....Lol

Интересно,какая модель вам больше всего понравилась в работе?

Did you notice the jam nut on the 3rd link must not have been tightened? It was threading itself around at the end

Что это и для чего?

Yeah I though it strange to drive an axle flange also. You’re right it will reduce the ratio by half driven this way so if the ring and pinion is for example 3:1 his effective ratio is 1:1.5 (speed increase from the PTO). Also the ring and pinion is loaded on its “coast” side. The gears aren’t cut to handle full load in this direction. He could have welded the side gears to the ring gear carrier, drove the differential at its drive shaft then used pulley size to gain the 1.5:1 increase. But as you’ve pointed out, it’s not driving a car. Looks like that tractor is under 30hp. Nice work overall.

I noticed the pinion shaft / spider gear problem also. Pinion shafts and spider gears don't have bearings so those gears are going to eventually bind and snap. A better solution would be to weld the spider gears and let the unused axle shaft spin freely. Another problem, although less severe, is the idler bearing located on the wrong side of the belt drive. Belts can only pull, not push, so it's important to put the idler pulley on the slack side of the belt instead of the tight side. Since there's a lot of rotational mass here, the drive and driven pulleys will change roles during a deceleration event of the engine. For this I would consider using a overrunning clutch on the PTO shaft. Otherwise, I like this design and plan to borrow a lot of ideas for my own someday :)