Hi Chris, thanks for this great machining video. I loved the close-ups of the bore, the internal thread and the final finish on the assembled parts checked with your giant micrometer, so good. Have a nice weekend Chris.
@raindeergames61045 ай бұрын
Always amazing to see what You do on this machine.
@mbury80045 ай бұрын
Well done from an old german machinist .
@lancer22045 ай бұрын
Interesting surface treatment on the coiling section at the end there. Nice work!
@ChrisMaj5 ай бұрын
Some type of carbide coating.
@BruceBoschek5 ай бұрын
Amazing, satisfying and beautiful work as always. Thanks very much, Chris.
@jimsvideos72015 ай бұрын
This is one of those things that people rely on without even knowing it exists.
@ChrisMaj5 ай бұрын
You right.
@paulbennett63795 ай бұрын
Nicely done as always chris
@johnlawler16265 ай бұрын
Nice bit of turning and milling, thanks for sharing 👍
@MattysWorkshop5 ай бұрын
Gday Chris, beautiful job as always mate, cheers
@paulcooper91355 ай бұрын
Amazing work! Thanks for sharing 🇨🇦
@catsmr5 ай бұрын
Great work!
@adambergendorff27025 ай бұрын
Awesome!
@warrenjones7445 ай бұрын
Chris these drawings you show us were all drawn by hand from the looks of things. Are these replacement parts or old designs for the parts you're are building? My point is I love the look of hand drawn prints. Every draftsman had a unique style and every one I have ever worked from was much nicer to use than the current cad stuff I get. Cheers
@ChrisMaj5 ай бұрын
Yeah, these are replacements and old designs.
@PundhyLuzino4 ай бұрын
Ini sangat hebat, 👍 Saya ingin seperti anda❤
@jasonwithrow79725 ай бұрын
It has been awhile since I have had a print given to me that was off a drafting board and hand lettered...
@ChrisMaj5 ай бұрын
I work with them almost daily. Some are in really good shape, and some look like they've been photocopied hundreds of times.
@MrKotBonifacy5 ай бұрын
Wypaśne ustrojstwo... Co by nie powiedzieć, że wręcz czaderskie ;-)
@sunradik5 ай бұрын
Ахуеть, какая точная работа!
@knight31154 ай бұрын
Are these tool paths created at the machine through canned cycles or hand writing code or are they typically third pary programed with software? Ive always wondered. Great work as always
@ChrisMaj4 ай бұрын
Mix of fanuc manual guide and G-codes
@Xris-FJ12005 ай бұрын
Many thanks, Magnificent job ! What sort of steel did you turn here ? Xris
@ChrisMaj5 ай бұрын
There was a mix. A36,1045 4140, and the shaft 4340.
@Kamil_Klukowski5 ай бұрын
Robi wrażenie. Ale jak wykobać ten podłużny otwór przez cały wał, zeby było prostoliniowo i współosiowo? Bo ten patyk w tym otworze przesuwając się powoduje wysuwanie tych ,,szczęk" (tak mi się wydaje, przynajmniej)? Do czego służy ten cały mechanizm i co przesuwa tym środkiem? Ogromne to.
@ChrisMaj5 ай бұрын
Jest sprzęt do głębokiego wiercenia. "Ten patyk 😅" rozszerza i zamyka cały mechanizm zwijający.
@localele15 ай бұрын
I seem to remember that you have used this lathe since it was new so a question for you. Have you ever had to adjust the base and tailstock of this lathe to keep it turning parallel? What sort of error would prompt you to make adjustments?
@ChrisMaj5 ай бұрын
I think the lathe bed was leveled twice since new. I do have to make small adjustments on the tailstock, but it depends on the size and length of the part I'm working on. Anything else, I'll just compensate in the program.
@localele15 ай бұрын
@@ChrisMaj Does that mean your Hankook controller has the ability to orient the z axis at an angle to the bed?