Make YOUR

Рет қаралды 35,941

Жыл бұрын

Today's video demonstrates how to relocate the fuel tank of a C10 from the cab to the interior of the rear frame rails. This essential modification makes your C10 much safer.
HOW TO REMOVE C10 BED: • How to Remove a Classi...
Purchase the conversion kit:
www.cjponyparts.com/fuel-tank...
Check out our text-based installation guide:
www.cjponyparts.com/resources...
Timestamps:
1:35 Taking seats out
2:00 Removing seat belts
2:30 Disconnecting fuel line & removing brackets for factory fuel tank
4:30 Disconnecting factory wiring for sending unit
4:50 Removing factory fuel tank
5:30 Remove the spare tire mount
6:00 Mocking NEW fuel tank up
7:00 Showing YOU where to cut
7:35 Cutting frame for filler neck
9:00 Mounting gas tank straps
11:30 Installing sending unit
13:30 Installing ground for sending unit
14:05 Installing new fuel line
16:00 Installing power wire for sending unit
18:00 Installing breather
19:00 Cutting bed of the truck
Subscribe for more info and installs:
kzfaq.info_c...
Music provided by:
elements.envato.com/curated
#cjponyparts #cjclassictruck #chevyc10 #chevrolet #truckmods #truckrestoration #diy #doityourself #c10

Пікірлер: 40

@patmcgowan5327 4 ай бұрын

After watching a few of these videos I have to wonder; why didn't they just build the tanks so they fit the trucks? Here's our tank kit. It doesn't fit but you can alter your truck enough to make it work.

@lightninsadventures2692 3 ай бұрын

It's because these are blazer gas tanks that just sort of work in the pickups. There are a couple of companies that sell custom fitted tanks that don't hang down near as low and don't require cutting the bed(except for where you decide to place the fill hole)

@kenlelon369 2 ай бұрын

Go Ahead!

@gunsandhorsepower 2 ай бұрын

Never had a ploblem with my 72 factory incab tank

@dannylinc6247 2 ай бұрын

Yep, 52 years and no broadside collision here, either. No smell of fuel, and 72 has heat expansion tube. But gas cap- locking is only offered in plastic, now.

@joeclark9042 3 ай бұрын

Oh yeah and I forgot what year did that sending unit come out of does it have any special ohms

@azastro919 11 ай бұрын

The only thing I would change is that brass float they always fill with gas. I've had to replace it 3 times in the last 2 years, I finally found a life cell float on summit thats solid all the way through.

@jimmysapien9961 8 ай бұрын

Thanks for that information

@santanaman6783 6 ай бұрын

And breather filter to above the tank too

@____MC____ Жыл бұрын

that bubble wrap under the carpet is gunna go flat where the floor mats are. Ive tried using a peice for a shoe insert at work and didnt last a few hrs.

@garthcarnell5420 Жыл бұрын

What tank supplier did you use?

@joeclark9042 3 ай бұрын

Hey bud I got a couple questions for you how many gallons is that gas tank what year is it and will that fit a 1988 GMC 2500

@matth5162 2 ай бұрын

Go watch brothers truck video on their tank it helps with the tank install alittle more

@JohnDoe-so9oy Жыл бұрын

Compromised the frame for looks should had at least reinforced the cutout. For DIY tank relocation shouldn’t have to remove the bed if that filler was designed slightly away made this project more daunting.

@CJClassicTrucks Жыл бұрын

The small cut in the frame for the filler neck is not going to compromise the frame by any means. A lot of people do it the exact same way & don't reinforce the frame rail. Also even if the filler was designed differently you'd still remove the bed because you have to cut out part of the bed sill out. Could you do all that with the bed on? Possibly but who would want to do that, its making the job harder for no reason.

@tbear802 Жыл бұрын

What size fuel line did you use and where did you get the caps to block off vent and return lines and what vent breather did you use Also what size fuel neck hose and gas cap yours is the only video I’ve seen installing the fuel line and breather I have a 1965 C10 so don’t think I need the return line and one vent line

@CJClassicTrucks Жыл бұрын

I bought the caps at a local parts store, they usually come with a couple different sizes & are pretty cheap. As far as the breather goes, we have those in stock on our website. As far as the fuel neck goes there’s another video on our channel showing you what hose & gas cap i use. Everything that I used for that is on our website as well too!

@JWROC83 Жыл бұрын

Can you not run flex pipe or whatever and use existing fuel area in cab. I would like to keep that look and have it functional not just for looks?

@CJClassicTrucks Жыл бұрын

I don't think that would work out well, after you relocate the tank its pretty far back so you'd have to run a super long flex pipe into the cab and also cut another hole in the cab to be able to route it back in the factory spot.

@rrrobin2569 Жыл бұрын

I just bought one of these. Where did you put your return fuel line? Did you use the vent tube next to the sending unit?

@CJClassicTrucks Жыл бұрын

Our truck has a carburetor so we didn't have to put in a return line

@rrrobin2569 Жыл бұрын

@CJ Classic Trucks Oh okay, I am running a 5.3L LS swap. I believe I should be able to use the vent tube next to the sending unit.

@arowe2140 6 ай бұрын

What did you use for the filler hose and where did you put the door?

@CJClassicTrucks 6 ай бұрын

we have a part 2 to this video on our channel showing that process!

@jimmysapien9961 8 ай бұрын

Is this only for carbureted or injection carburetor combo

@CJClassicTrucks 8 ай бұрын

nope you can use this gas tank for any platform

@ernestobermea4562 9 ай бұрын

Hey bro, Where can I get a new tank installation kit like this online??

@CJClassicTrucks 8 ай бұрын

We always put the part link in our description But here's a direct link to the gas tank! 😎 www.cjponyparts.com/fuel-tank-conversion-kit-truck-frame-rail-mount-chevrolet-c10-gmc-truck/p/FTK10/

@PeterHatch-mx7zc 11 ай бұрын

Do you have part numbers please

@CJClassicTrucks 11 ай бұрын

there's a link for the kit in our video description.

@PeterHatch-mx7zc 11 ай бұрын

Can't find it can you give them part number thks

@CJClassicTrucks 11 ай бұрын

www.cjponyparts.com/fuel-tank-conversion-kit-truck-frame-rail-mount-chevrolet-c10-gmc-truck/p/FTK10/ part number FTK10@@PeterHatch-mx7zc

@pjnelson8971 Жыл бұрын

Yeah... let's go ahead and stop saying 'go ahead'.

@demarques1911 7 ай бұрын

😂😂😂

@dannylinc6247 2 ай бұрын

Fill er neck😂

@raygottschall9101 Жыл бұрын

Plasma cutter works much better

@ryanfox7529 7 ай бұрын

Good Job! I can't cut my frame . Goes against my religion. Also the tank looks to low in my opinion.

@CJClassicTrucks 7 ай бұрын

I was worried about it sitting low too. Our truck is lowered a good bit and it's actually not to bad, we have some pretty bad roads around here and I have no issues with it.

@stephenmalone2314 6 ай бұрын

Your right the tank sits way to low !

@robertemmons2260 4 ай бұрын

For a professional company, I'm not impressed. Im not seeing any professional results on this tank install. Here is why I had said this. For the fuel line, i will not use a rubber fuel line for long runs. Rubber fuel lines shouldn't be longer than six inches max for joints. Avoid using zip ties to secure your fuel line. They can become brittle over time. Use conduit or tubing clips instead to secure your hardlines. At the fuel inlet, instead of cutting into the franerail, just simply heat and bend, or pound the frame lip down. It's better to have displaced metal for strength than it is to have metal removed. If at all possible, run your sending unit wire (and fuel pump wiring if using an electric fuel pump) inside the factory or new wire loom. Other than that, this is a good fuel tank conversion. I have this conversion for my '68 C10 using this same tank from your company.