Make Your Own Fast RC Mini Racing Drone!

Рет қаралды 96,106

3 жыл бұрын

Try out PCBWay: www.pcbway.com/
Get $5.00 in-credit welcome bonus after joining: www.pcbway.com/Member/Login/
---------------------------------------------------------------------
In this video, we're making a fast indoor/outdoor mini racing drone from some common materials, also using a JJRC/Eachine drone receiver board with a mini transmitter.
With a calculated top speed of around 30-35kph or 18-21mph, this racing drone is a true racer! It can handle being flown outdoors even in windy-ish conditions!
----------------------------------------------------------------------
👉 Visit my online Storefront: sites.google.com/view/maximag...
----------------------------------------------------------------------
☕ Buy me a coffee: www.buymeacoffee.com/MaxImagi...
----------------------------------------------------------------------
Instagram: @max.imagination - max.imagina...
Instructables page: www.instructables.com/member/...
----------------------------------------------------------------------
Disclaimer: Amazon purchase links below are affiliate links. It doesn't cost you extra to buy through those and I just get a tiny commission. Thank you!
Parts and materials needed to build this mini drone:
(x1) Transmitter/controller + Receiver - www.aliexpress.com/i/40002285...
(x4) 3.7V 6mm High-speed Coreless motor - amzn.to/3rUqPJm
(x4) Propellers - amzn.to/3g34aI5
(x1) 3.7V 150mAh Li-Po battery - amzn.to/3CD44ym
Or 3.7V 220mAh Li-Po battery - amzn.to/3ivxUPH
(x1) Short section of Plastic Cable Raceway (Trim off and use "U"-shaped sections) - amzn.to/3yGN35A
(x3) Popsicle sticks - amzn.to/3VtiIB6
(x1) Old ink pen
(x1) Square piece of foam
🪛🔧🔨 Tools and extra supplies I use:
➡️ Soldering Iron Kit - amzn.to/3X6L5Wq
➡️ Hot Glue Gun - amzn.to/3E6trJG
➡️ Drill Machine - amzn.to/3EDe0u8
➡️ Box cutter/Utility knife - amzn.to/3hP9MGI
➡️ X-Acto Hobby Knife - amzn.to/3XbL7ML
➡️ Cutting Matt (Green) - amzn.to/3gil71A
➡️ Needle-nose Pliers - amzn.to/3ECTKc3
➡️ Wire Cutters for Electronics - amzn.to/3ECut1B
➡️ Wire-stripping tool (Automatic) - amzn.to/3hQsMVD
➡️ Screwdriver kit - amzn.to/3V6vgNX
➡️ Heat-shrink Tube Kit - amzn.to/3AksTPE
➡️ Jumper Wire Kit - amzn.to/3UGhMZq
➡️ Breadboard for Prototyping - amzn.to/3GlF4ze
➡️ Perf Boards, Pin headers, and Connectors Kit - amzn.to/3AkySUw
➡️ Superglue - amzn.to/3EE6uis
➡️ Duct Tape - amzn.to/3g5mTU0
➡️ Double-sided Tape - amzn.to/3Edta82
➡️ Kapton Tape (for battery leads) - amzn.to/3X58bNl
---------------------------------------------------------------
//////////////////////////
Music credits:
Roboskater by Audionautix is licensed under a Creative Commons Attribution 4.0 license. creativecommons.org/licenses/...
Artist: audionautix.com/
Hip Hop Rap Instrumental (Crying Over You) by christophermorrow
/ chris-morrow-3
Creative Commons - Attribution 3.0 Unported- CC BY 3.0
Free Download / Stream: bit.ly/2AHA5G9
Music promoted by Audio Library • Hip Hop Rap Instrument...
V.I.P.N - "SKY" MOONY TRAP BEAT | No Copyright Trap
Free Download Link
bit.ly/3oQ6Ysv
V.I.P.N
kzfaq.info/love/2KS...
/ realvipn
/ vipnbeats
/ vipn
//////////////////////////
You may have also found this video by searching the following keywords:
drone, quadcopter, racing drone, diy drone, diy quadcopter, homemade,
homemade drone, diy, how to make, how to, fast drone, easy to make, simple drone, easy to make drone, drone that can fly, flying drone, flying, budget drone build, drone build, rc, remote control, radio control, rc drone, at home, mini rc drone, mini drone, helicopter, copter, rc aircraft, aircraft, hover, Mini RC racing drone, DIY quadcopter, Fast mini drone, RC drone building, Mini racing drone tutorial, DIY racing quadcopter, How to make a mini drone, Build your own racing drone, Mini quadcopter DIY guide, Fast RC drone build, Mini drone racing tutorial, Step-by-step drone assembly, Racing drone building tips, DIY mini racing quadcopter, RC drone, Mini drone speed modifications, Racing drone components, Building a fast quadcopter, Mini drone racing techniques, Customizing your racing drone, Tips for building a mini racing drone, Mini drone modification guide, Building a lightweight racing quadcopter, Racing drone electronics guide, Mini drone aerodynamics tips
#racingdrone #quadcopter #diydrone

Пікірлер: 219

@MaxImagination 2 жыл бұрын

Hey everyone! The comment section has finally been re-enabled over the whole channel after 2 years by KZfaq themselves who shut it down in the first place. Glad to be in touch with my viewers again! :)

@Th3Exodia 2 жыл бұрын

hi i just have a question can something be attached to it like i want to fly it with esp8266 with small lipo battery is that possible can it hold that ?

@MaxImagination 2 жыл бұрын

@@Th3Exodia Hi, that may be possible if your ESP32 SoC is on its own without PCB. Yes, I believe with that it should lift. Cheers, Max

@houseoflaugher7923 2 жыл бұрын

Pls can you give me the link for the receiver Bord pls

@MaxImagination 2 жыл бұрын

@@houseoflaugher7923 Hi, the only available purchase page of the receiver and transmitter is linked in the description below the video. Cheers ✌🏻

@sanjussnjaysanjusanjay3301 Жыл бұрын

Gggthcz

@LZDILLC Жыл бұрын

Great job lil bro!! My kids need friends like you..

@MaxImagination Жыл бұрын

I appreciate that!

@akinawa3399 2 жыл бұрын

Young and smart . I really love to see the young people like you 🐱

@MaxImagination 2 жыл бұрын

Thank you so much! I appreciate hearing such kind comments as your's :)

@kuzadupa185 Жыл бұрын

I do something similar with the legs but i flare my legs, on the upper portion, by making 3 cuts and fanning the top "wings" outwards, so when i drop the leg into the arms loop, it will naturally have resistance and not go any further. It provides that extra amount of security that I like having, so when I land or take off, the motor doesnt slip put up or out down. To prevent slipping down, you can make 2 slight cuts a few mm apart on the bottom bottom, and bend that portion in. When you place the motor in that bent in part will naturally clip the motor in place.

@MaxImagination Жыл бұрын

You sound ahead of your craft! That seems like a more secure solution for DIY drones when using cable raceways. Thanks for the tip!

@johnmichaels4330 Жыл бұрын

Very cool. Great ideas in here.

@bigredwatermelon Жыл бұрын

Really cool DIY project

@MaxImagination Жыл бұрын

Thank you! 👍

@lakhvendrakumar4554 Жыл бұрын

Amazing bro. salute your work...

@MaxImagination Жыл бұрын

Thank you 🙌

@Nabhaanibrahim16 9 күн бұрын

I never thought it would be this easy! Thanks so much, I'll make one myself from your help! Just want to know, can I ask you questions here in the comments section in case I'm stuck or confused?

@Nabhaanibrahim16 9 күн бұрын

Already got a question! What's the weight of the drone? Want to know as I am purchasing motors and blades from elsewhere, so I need to know sufficient power.

@MaxImagination 8 күн бұрын

Hey! Firsly, I highly suggest you instead follow my updated video on this type of drone, check out my second to last KZfaq video. Sure, no problem. You can ask for help in case you get stuck by making a new comment. This drone weighs around 20 grams.

@Nabhaanibrahim16 8 күн бұрын

@@MaxImagination Thanks so much! But the new one I saw, is a lot more complicated as I am a beginner. This one looks simple. But I am going to leave it to you to make the final suggestion (if the complicated-ness of the new one is worth it or not, for beginners). ... By the way I am an old subscriber :)

@dustinstubbs3170 2 жыл бұрын

your awesome dude your like Enstein or something I can't believe you built this racing drone!!!

@MaxImagination 2 жыл бұрын

Thanks so much :)

@ULTRA_velocity 3 ай бұрын

Can I use brushless motors instead with this accelerometer never mind the battery and other components?

@MaxImagination 3 ай бұрын

No, it won't work. You'd need a different receiver with brushless ESCs for the motors.

@JWStruggle 2 жыл бұрын

Great DYI! Curious what the estimated cost was for this build? BTW second link on parts list is unavailable as of this post

@MaxImagination 2 жыл бұрын

Hi there, thanks for watching! The cost for making this drone was about $10, the cost may vary depending on what parts you already have and don't. Sorry about the unavailable product on that link, I couldn't find a substitute controller that's in stock, you'll either have to do a bit of your own searching around to find the corresponding part, or wait til the part is back in stock for that link. I don't really have any control of that. Have a good weekend! Cheers

@factstheory168 2 жыл бұрын

Great drone

@MaxImagination 2 жыл бұрын

Thanks! Cheers :)

@MegaTechno 4 ай бұрын

What is the total weight of the drone? I will make one

@MaxImagination 4 ай бұрын

~25 grams. Have fun making!

@allrounderchannel471 2 жыл бұрын

It will fly

@s.parthiban9717 2 жыл бұрын

Wow amazing bro nice video 👍👍👍

@MaxImagination 2 жыл бұрын

Many thanks! :D

@mohanadrahiem Жыл бұрын

Great job,can you use small brushless motor instead of the brushed ones ?

@MaxImagination Жыл бұрын

Hi there. Thank you! No, brushless motors cannot be used with this type of drone.

@r.aviations4100 2 жыл бұрын

Great work bro (full support)👍

@MaxImagination 2 жыл бұрын

Thanks for your support! 👍

@swiftbat2599 Жыл бұрын

@@MaxImagination thanks

@ebiringam 6 ай бұрын

Max your projects are always good keep it up

@MaxImagination 6 ай бұрын

I appreciate that, thanks!

@mehedihossainsami1038 11 ай бұрын

The drone is really so cool,bro🔥🔥

@MaxImagination 11 ай бұрын

Thank you! Stay tuned for the upcoming video on a micro FPV RC car!

@rsuriyop 10 ай бұрын

Hey this is great and very informative for us beginners. Just one question though... What if you're buying the remote control and receiver circuit board individually? How do you sync them together?

@MaxImagination 10 ай бұрын

Hi there. Thanks! You cannot easily sync a different factory remote and foreign receiver together as they're most likely programmed to operate on different channels and bands on a certain frequency.

@rsuriyop 10 ай бұрын

@@MaxImagination Thanks for the reply. That's what I was thinking but just wanted to double check to make sure. Problem is, it seems that they are hard to find selling together, at least on eBay. So I had to check Ali Baba to find what I needed (remote + receiver). And sure enough, I think I was able find what I needed. Thanks again :)

@AyaadhAmeen 2 жыл бұрын

I am subscribing

@iamjustice7421 2 жыл бұрын

Yo.. Nice work

@MaxImagination 2 жыл бұрын

Thanks! :D

@noimnotarobotcanubeleiveit7024 14 күн бұрын

I have several types of coreless motors with props and build light frames with 3d pen. None of them seem to get off the ground and the motors end up hot.

@MaxImagination 12 күн бұрын

You need higher performance coreless motors intended for mini drones, you can check out my latest mini drone video on my channel and check the video description for the product link to the coreless motors I'm talking about.

@slyasastech 3 жыл бұрын

Hi max I'm your big fan . I'm doing electrical projects like you . Nice to meet you . I'm from sri lanka

@MaxImagination 3 жыл бұрын

Hello, thanks for commenting! Nice to communicate with you too ☺ I'll check your channel out ✌

@prajwal3433 2 жыл бұрын

watching from nepal. Bro you make very nice vedio🤠🤠

@MaxImagination 2 жыл бұрын

Thanks and welcome!

@subarubrz331 Жыл бұрын

wow nice

@MaxImagination Жыл бұрын

Thanks for watching! :)

@leochang492 Жыл бұрын

你的影片很棒加油

@justa._.guy21 Жыл бұрын

Great DIY! BTW Where to buy or get the remote?

@MaxImagination Жыл бұрын

Hi and thanks! The remote is currently unavailable in the market.

@brankazrilic1040 3 ай бұрын

Hey Max, love your videos and I was looking to build a similar version of this drone but do you know what is the range of the drone, greetings from Croatia!

@MaxImagination 3 ай бұрын

Hey! Thank you! It's range is around 50-100 meters.

@wachagain432 4 ай бұрын

You channel is actually a gem bro ❤

@MaxImagination 4 ай бұрын

I appreciate that!

@adebiyi-olumayowayemisi2307 8 ай бұрын

Where can you see that same flight controller also the electric wire cover

@MaxImagination 8 ай бұрын

Check it out via the purchase link below.

@adebiyi-olumayowayemisi2307 8 ай бұрын

What of the remote control and battery

@qwertyqwerty9587 6 ай бұрын

Cool, You ever have any problems with over discharge on those batteries

@MaxImagination 6 ай бұрын

Not that I've experienced. The circuit board regulates that and cuts off power for flight when the battery gets too low. However, it is up to you to unplug the battery to prevent over discharge from the light load of the blinking LEDs.

@user-es3gm1rj5k 2 ай бұрын

Good job 👍How many trust can get using one motor and what is the weight of this drone?

@MaxImagination 2 ай бұрын

Thanks for your comment! It weighs 25 grams.

@beastking1234 8 ай бұрын

Can u make like a KZfaq short on how to make a case for the controller because I got it but the controller comes without a case

@xxem_al33 Жыл бұрын

so i was looking for the cable raceway and I couldn’t find it anywhere, do you know what kind it is?

@MaxImagination Жыл бұрын

Hi there. Thanks for watching. Here's a link to a cable raceway kit I recommend that contains the correct sections of track you can slice from to get a sturdy frame for your drone: amzn.to/3AEP9CY Cheers, Max

@kspcreation666 3 жыл бұрын

Comments are finally back. Amazing 🔥🔥

@MaxImagination 3 жыл бұрын

Yeah! Thanks for your support, KSP!

@ULTRA_velocity 3 ай бұрын

Do you have any info on what protocol that the receiver uses

@MaxImagination 3 ай бұрын

I do not, unfortunately. You may have to dig deeper online.

@user-es3gm1rj5k 2 ай бұрын

👍.what motor you used for this. Is that 716 moter

@MaxImagination 2 ай бұрын

6mm coreless motor

@amazing_memes2684 Жыл бұрын

Hey very good DIY i have just one questions how do you connect the controller to the receiver

@MaxImagination Жыл бұрын

Hi and thank you. The controller automatically pairs to the receiver after powering both.

@amazing_memes2684 Жыл бұрын

@@MaxImagination okay thank you very much

@Marchellu Жыл бұрын

can u put camera on it, small one like 26gb

@MaxImagination Жыл бұрын

Hi there. Lightweight cameras such as 2-megapixel micro action cams may work. Anything heavier than 10 grams will restrict the drone from taking off into the air.

@QQ-ze1rx 2 жыл бұрын

What soldering tool do you use?

@MaxImagination 2 жыл бұрын

I use the soldering iron from a kit similar to this one, my brand though is 'Anbes' www.amazon.com/Soldering-Iron-Kit-Temperature-Desoldering/dp/B07S61WT16/ref=sr_1_3?dchild=1&keywords=anbes+soldering+iron+kit&qid=1630107939&sr=8-3

@beastking1234 8 ай бұрын

How would u add a camera to this drone

@MaxImagination 8 ай бұрын

A 2MP camera underneath with a lightweight battery should do.

@habibur9222 2 жыл бұрын

Nice video 🇧🇩🇧🇩🇧🇩🇧🇩🇧🇩

@IdeasbySuyashDesai 3 жыл бұрын

Very Cool Project Max! And very Nice explanation.

@MaxImagination 3 жыл бұрын

Thanks a lot! 😀😊

@Crazy_22119 Жыл бұрын

Hi buddy!! Can we use the Radio controller made by you and how to give connection to the receiver that you made.Its and Emergency buddy Pls explain me❤

@MaxImagination Жыл бұрын

Hi there. I would have to show you how it needs to be done, I cannot explain that here in the comments... It is possible, though!

@Crazy_22119 Жыл бұрын

@@MaxImagination Ok Buddy.Please Make a video about that

@haneen3731 2 жыл бұрын

Thanks for this video, however some links (the one for the transmitter) seems to be broken. Could you please check them and update it. Thanks!

@MaxImagination 2 жыл бұрын

Hi, thanks for letting me know! I'll update the links soon!

@haneen3731 2 жыл бұрын

@@MaxImagination Awesome! Thanks

@multigek2276 3 жыл бұрын

I have a question can you also install an fpv camera on this drone??

@MaxImagination 3 жыл бұрын

Hi, yes you can. Though it may require you to get a different receiver of a more professional sort, that can support an FPV camera and system.

@multigek2276 3 жыл бұрын

@@MaxImagination thank you

@MaxImagination 3 жыл бұрын

@@multigek2276 No problem! :)

@manulaposhitha9591 3 жыл бұрын

Good I am from srilanka

@asmakhadimmuhammad9985 Жыл бұрын

Great job bro.can my son get some classes from you?

@MaxImagination Жыл бұрын

Hi there! Thanks for your comment. Currently, I don't do classes, but in the future I may put together a course :)

@asmakhadimmuhammad9985 Жыл бұрын

Thanks. My son is waiting anxiously

@animeguy9007 2 жыл бұрын

I hope you respond cause im in need so i bought eachine transmiter and a different eachine receiver and the both dont receive and transmit so what shall i do ? or i should bind them? plz help

@MaxImagination 2 жыл бұрын

Hi, First, please tell me the Transmitter and receiver models you bought.

@animeguy9007 2 жыл бұрын

@@MaxImagination ok here are they Eachine E50S RC Quadcopter Spare Parts Receiver Board Eachine E57 RC Quadcopter Spare Parts Transmitter

@AaharshHD Жыл бұрын

Bro max, can use bt5636cyrl receiver

@MaxImagination Жыл бұрын

Hi there. Never heard of it. I'll check it out.

@rohanmandal-oj2bc 17 күн бұрын

I am highly inspired from you Bug brother...i am from india...it is one of my childhood dreams to fly something....you showed me the way to it...Thanks for that, but does this drone really fly at a speed of 35km/h ?

@MaxImagination 12 күн бұрын

Hi there. Thank you and glad my video helped :) The drone really flies that fast at full speed when fully tilted.

@rohanmandal-oj2bc 12 күн бұрын

@@MaxImagination big bro actually I want to make a special drone project For a certain problem solving, I got to know from your video that I can build in a less budget

@copyismystyle 2 жыл бұрын

Hi max i have loved this invention and i want to build to but i have a different transmitter and reciver it is squared shape pls help me do this

@copyismystyle 2 жыл бұрын

Pls i need help to make it and can we use 300 mah 3.7 volt lipo battery ?

@copyismystyle 2 жыл бұрын

I have a rectangle transmiter too

@MaxImagination 2 жыл бұрын

Hi. Thanks for watching! You could build yourself a drone with such receiver and battery. However, you'd probably need to scale up the frame in size (a bit) as well as the coreless motors.

@MaxImagination 2 жыл бұрын

Yes, you could.

@copyismystyle 2 жыл бұрын

Thanks thank you very much

@mohammadanasusmani7928 3 жыл бұрын

can we attach a camara with it

@MaxImagination 3 жыл бұрын

Hi, yes you can, but as any other little camera would probably outweigh the drone, we'd need to attach one with a small camera sensor which has a really simple function of just filming to a Micro SD card. Then I believe such a setup would work. Cheers!

@jeanpaulking1804 Жыл бұрын

Put the fpv camera

@vijayaupadhyay2945 Жыл бұрын

It will be connected to controller or we have to connect it

@MaxImagination Жыл бұрын

You need a controller remotely connected to it via Radio Frequency, yes. No pairing needed, powering on the two devices simply does it.

@ULTRA_velocity 4 ай бұрын

What about the controller? Does any work?

@MaxImagination 4 ай бұрын

Hi. Not just any controller works. You need to purchase or find a drone's receiver and transmitter pair that are programmed to work with one another.

@hamseem 5 ай бұрын

Hey! I know its been a while since this video was uploaded, but i have a question. Im making an autonomous variation of your drone design, using a XIAO ESP32S3 Sense microcontroller, an mpu6050, and drv8833 motor drivers, I have 320 mAh lipo battery, and am using a tri copter design with 3 motors instead of 4, but for some reason, it stalls after running for a little bit at high speeds, do you have any idea why this is?

@MaxImagination 5 ай бұрын

Hi there! Such issue sounds like something coming from the motor driver's end. You may have picked a motor driver too weak for the higher currents the motors reach when at full throttle. You will definitely need to check that first. Cheers.

@mankalumngwin-ki8qy Жыл бұрын

how can I get a colorless motor

@MaxImagination Жыл бұрын

From Amazon: amzn.to/44BVGf1

@user-tg6pv4cj2w 6 ай бұрын

How long will it take to come

@MaxImagination 6 ай бұрын

Sorry, what did you mean?

@ADSninja30 Жыл бұрын

From where can i get the transmitter?

@MaxImagination Жыл бұрын

At the moment, it is hard to acquire this exact transmitter. It is unavailable in online stores. I will one day focus on making an Arduino based drone that anyone can get the parts for. Cheers.

@ADSninja30 Жыл бұрын

@@MaxImagination thanks for replying Btw can you make a receiver and transmitter based on infrared light emitting diodes and IR receivers??

@r.aviations4100 2 жыл бұрын

Where can i buy this recirver. I am unable to open the link in the description

@MaxImagination 2 жыл бұрын

Hi, Sorry about that! It has become pretty difficult to find any online stored that sell such receiver and transmitter pair up until now. I found the exact pair for a decent price. Purchase link: www.rc-helicopter-spare-parts-online.com/jjrc-h36-e010-quadcopter-spare-parts-pcb-board-transmitter-p-11736.html Hope that helps! Cheers, Max

@r.aviations4100 2 жыл бұрын

@@MaxImagination thank you

@DynoPlayz873 3 жыл бұрын

Max bro can I use 614 coreless motor with 3.7 380 mah battery And finally ask you my doubts comments are back 🎉🎉

@MaxImagination 3 жыл бұрын

Hi there, thanks for watching. Yes you may use a 614 or even 612 type coreless motor with a 380mAh battery, sure :) Yes, my comment section is back under all of my videos, finally KZfaq unblocked them

@DynoPlayz873 3 жыл бұрын

@@MaxImagination I am so happy bro 😊

@MaxImagination 3 жыл бұрын

@@DynoPlayz873 :D

@ULTRA_velocity 4 ай бұрын

Do You know the specifications of the receiver so I can get a transmitter for it?

@MaxImagination 4 ай бұрын

It uses the "JR-NH010R" receiver board.

@MaxImagination 4 ай бұрын

P.S. You can purchase the transmitter and receiver for it via the link in the video description.

@ULTRA_velocity 4 ай бұрын

I did some research but couldn’t find anything about the receiver

@ULTRA_velocity 4 ай бұрын

Do You have any info about the protocol it uses?

@nagasheshumalleboyina1458 3 ай бұрын

Name of the receiver you used

@MaxImagination 3 ай бұрын

It does not have a "name", only a model number by which you will not find it online anymore. You can acquire these receiver boards online. This one came from a broken Eachine E010 drone.

@techlap5799 2 жыл бұрын

do we need to program the drone or not

@MaxImagination 2 жыл бұрын

Hi, if you're using the transmitter and receiver like the ones in the video, you don't have to, no.

@kenjieroportugal2625 Ай бұрын

what if I have no receiver but have a transmitter?

@MaxImagination Ай бұрын

Then you need to get a receiver.

@techninismworld2875 11 ай бұрын

Is there any motor speed controller

@MaxImagination 11 ай бұрын

No as it's a part of the receiver board.

@thashanyokesh1556 Ай бұрын

Can you make a drone that can be controlled by mobile

@MaxImagination Ай бұрын

Will consider it for a potential future drone project. It can be done if an ESP32 is used in the equation.

@QQ-ze1rx 2 жыл бұрын

Sadly i cant find the transmitter only a spare part of the transmitter

@MaxImagination 2 жыл бұрын

Apparently, they are out of stock on these transmitters at the moment, sorry! 😕

@swiftbat2599 Жыл бұрын

How do I know which part is front and back or left and right

@MaxImagination Жыл бұрын

The LEDs onboard the Receiver indicate direction. Blue = front, Red = back.

@swiftbat2599 Жыл бұрын

Thank you

@auntinath2935 9 ай бұрын

What is your reseivers name?

@MaxImagination 9 ай бұрын

"JR-NH010R" is my receiver board's name.

@AaharshHD Жыл бұрын

Bro Max, I'ts such a pleasure to meet you. I'm your fan and I am from Srilanka. I really want to make this product. So I checked out the link you gave in the description. Unfortunately they are Douglas I cant effort to buy it. Can you give a link for srilanka please?

@MaxImagination Жыл бұрын

Hi, Kalpana. Many thanks for following along with my journey! Unfortunately due to the unavailability, you can no longer purchase the transmitter nor receiver/flight controller boards to make this drone, making it a harder project to complete. Sorry for the inconvenience!

@AaharshHD Жыл бұрын

Thanks for letting me know, but do you know any other store to buy these stuff?

@AaharshHD Жыл бұрын

And can we be friends

@ebiringam 6 ай бұрын

Hello max do you do electrical engineering in school

@MaxImagination 6 ай бұрын

I study it on my own online :)

@AaharshHD Жыл бұрын

Bro can I connect a camera on it

@MaxImagination Жыл бұрын

Yup, I think you can, as long as it's lightweight.

@AAHARSHAN591 Жыл бұрын

hi bro where can i get the pen pipe 😀

@MaxImagination Жыл бұрын

From one of your old ink pens 🤓 Or, you may purchase a new pen and use its plastic casing.

@AAHARSHAN591 Жыл бұрын

@@MaxImagination thanks bro i am the one who is browsing from kalpana and ia m aaharshan i am her son

@pravindeshmukh1462 Жыл бұрын

How to make a remote

@emmy0021 2 жыл бұрын

How much does it weigh?

@MaxImagination 2 жыл бұрын

Not sure, sorry! Currently I don't have a hobby scale to know its weight :/

@swiftbat2599 Жыл бұрын

Hello, I am in India. The transmitter and receiver are unavailable here. Can you you please suggest any alternatives?

@MaxImagination Жыл бұрын

Hi there! I'd be unable to give you Amazon links to the parts you're missing, but I've found some purchase links from Banggood - Transmitter: www.banggood.com/Eachine-E017-Mini-RC-Drone-Quadcopter-Spare-Parts-Remote-Controller-Transmitter-p-1979012.html?cur_warehouse=CN&rmmds=buy Receiver: www.banggood.com/Eachine-E017-Mini-RC-Drone-Quadcopter-Spare-Parts-Receiver-Board-p-1981798.html?rmmds=detail-left-hotproducts&cur_warehouse=CN&trace_id=bcd61680659630822 Cheers.

@swiftbat2599 Жыл бұрын

@@MaxImagination so, i have to do something to pair the transmitter and receiver? If yes, how?

@thinkbig233 3 жыл бұрын

Wow I like your all creation..

@MaxImagination 3 жыл бұрын

Thanks so much! Take care 😊✌

@ssdh601 2 жыл бұрын

alternate link for transmitter

@MaxImagination 2 жыл бұрын

Don't have one at the moment, sorry about that! I'd assume this transmitter and receiver pair are no longer being manufactured, therefore less and less sellers are out there for selling those.

@tanushreekarmakar1609 4 ай бұрын

Max can you please send me the PCB and the control

@MaxImagination 4 ай бұрын

I cannot do that for you. However, you can purchase the controller online.

@wasimsayyed6279 Жыл бұрын

What about remote how to make remote ?????

@MaxImagination Жыл бұрын

I do not have a tutorial on the remote, sorry! The controller is currently unavailable to be purchased.

@ebiringam 6 ай бұрын

Hello max please can buy this drone

@MaxImagination 6 ай бұрын

Hello! I do not sell my projects. You can find other factory-made drones similar to this on online stores.

@user-zr4wp8di4u 2 ай бұрын

What about software

@MaxImagination 2 ай бұрын

No software config needed.

@user-ww8ud1zc2q 8 ай бұрын

Bhai mobile ka camera 📷 to banana batao

@Sha_hal 3 жыл бұрын

Bro link not geting

@MaxImagination 3 жыл бұрын

Hi, there are links pasted in the description below my video, please check them out.

@user-tg6pv4cj2w 6 ай бұрын

How much please ❤❤❤

@MaxImagination 6 ай бұрын

Depending from the region you are in, price can vary from $15-45 US dollars to build one.

@AryanPowar-jv9sv 3 ай бұрын

I am your subscriber from india , can you pls send a cheap controller and receiver buying link pls , cuz your link won't be working

@AryanPowar-jv9sv 3 ай бұрын

Pls it's dealer should be belong to india

@MaxImagination 3 ай бұрын

Hi. I haven't been able to find a link to a controller and receiver pair that are made for this type of drone other than on where I linked already. I suggest you do your own research online in your own country's online stores.