Making a DIY Small Sandblaster | Homemade Sandblaster

Рет қаралды 58,782

Жыл бұрын

Hello Guys . After a long brake I m back to videos . I never stopped plan projects for my channel so I have a lot and interesting projects for the future.
I made a small video just for the start enjoye it .
New season start in October so see you soon !

Пікірлер: 19

@MaverickProjectsOfficial Жыл бұрын

Hi everyone ! After long brake Im back to my (new) workshop and here is a small project. New videos comming soon. Tell me your ideas what would you like to see on my channel ?

@krazmokramer Жыл бұрын

While this is an interesting concept and video, the results are far from ideal. A good pen style sand blaster isn't much more expensive than the parts required for this project. And the results are much more impressive. I have used the pen style for over 40 years, first as a dental lab technician and then as a dentist. Your project has the advantage of a larger hopper capacity. Thanks for the video.

@kevino6670 Жыл бұрын

Hello, is there a place where anyone can get dental media & the pen style trigger?

@MicBergsma Жыл бұрын

Curious how much total cost for materials?

@brianbeck4740 11 ай бұрын

Ok help me out here, I made one of these but the bottle exploded and media went everywhere. What did I do wrong? I used all same size fittings. 1/8-1/8

@brianbeck4740 11 ай бұрын

There was a lot of air flowing up into the bottle. How do I prevent this.

@shadowline1413 Жыл бұрын

Wich Spark Plug you used for that?

@MaverickProjectsOfficial Жыл бұрын

Hello I used a c7hsa sprak plug.

@Vladimirtub Жыл бұрын

Very nice work! Small diameter of plastic bottle under pressure... Are you engineer?

@jdhappy7663 Жыл бұрын

I made one similar to this but it will not constantly spray sand. If I hold the trigger the sand stops and if I pulled sit it doesn't spray enough to clean anything. I appreciate any ideas or help

@MaverickProjectsOfficial Жыл бұрын

Did you used the same parts? What type of sandblasting material you used ? Also before sandblasting turn the upside down hold the trigger to spray clean air and then turn it again and start blasting.

@jdhappy7663 Жыл бұрын

@@MaverickProjectsOfficial I did not use the same tip that you used. I made two different ones using different tee's and different guns and had the same results with both.

@tomkeegan3782 11 ай бұрын

It doesn't work, the air blows the sand back into the bottle, the only way to get sand to come out is to stop the airflow briefly, so it's stop start, stop start, I can't spray continuously.

@stirrlingsaunas 8 ай бұрын

got the same problem

@vanDCreative 5 ай бұрын

You’re pulling a vacuum in the bottle, at some point you need to let some air back into the bottle, put a hole in the top of the bottle to allow for some air to get back in. That T junction always pulls a vacuum on the 90 degree line when air rushes through the straight line

@3zooz697 Жыл бұрын

🐢🐢🐢🐢🐢

@MsRae222 10 ай бұрын

EBay is an online service that

@user-qg1yl8el2i Ай бұрын

Сделал воздух пошол в бутылку и она взорвалась🤔

@robertsondereka 5 ай бұрын

For the love of God have someone that knows what they're doing edit this crap. Literally! Have! To! Painstakingly! watch! Every! Single! Goddamn! Twist! And! Turn this video could have been an hour shorter and still got the same point across