Making a Floating Wine Bottle Holder and Cheese Board

Making a Floating Wine Bottle Holder and Cheese Board - Woodworking Gift Ideas

Рет қаралды 8,166

Күн бұрын

Making some great woodworking gift ideas, including a floating wine bottle holder and and also a face grain cutting board (I call it a cheese board). The video also includes the floating wine bottle holder plans. A fun woodworking project!
The work of Jacob at The Wood Plank inspired the design on the cheese board in this video. He does amazing work! Check it out at... @thewoodplank4376
Links to tools used or referenced in this video. *affiliate
Drill press - amzn.to/3V5sXtW
Planer - amzn.to/3BNRTPQ
Jointer - amzn.to/3WxLPCU
Forstner bit - amzn.to/3v03lUR
Hole saw - amzn.to/3PDmzZU
Table saw push stick - amzn.to/3YEjAEo
Table saw push block - amzn.to/3G4RgDT
Titebond III wood glue - amzn.to/3PMMheA
Mineral oil - amzn.to/3VbOT6A
Cutting board wax - amzn.to/3Vcaegp
Drill sanding attachment for hole - amzn.to/3YDFaJ8
Palm orbital sander - amzn.to/3j6xYVK
Router bit for cracker groove - amzn.to/3V61fgN
Parallel clamps - amzn.to/3BJQSbl
0:00 - Intro
0:28 - Wine bottle holder Sketchup model
1:50 - Making the jig
5:24 - Making the wine bottle holders
7:18 - Making the cutting board (cheese board)
10:44 - Applying the finish
*affiliate - As an Amazon Associate I earn from qualifying purchases, at no additional cost to you.

Пікірлер: 15

@blakepresent Жыл бұрын

Thank you, what a great video. I can’t wait start making them for friends and family.

@jkmwoodworking Жыл бұрын

Thank you so much for the kind words!

@holzapfela Жыл бұрын

Your videos are great - I really appreciate you taking the time to share your process with us. I would love to replicate your table at some point!

@jkmwoodworking Жыл бұрын

Thank you for the kind words! It's greatly appreciated!

@mariusbeilharz5674 Жыл бұрын

Awesome Channel! Glad I found it. Greetings from Germany :)

@jkmwoodworking Жыл бұрын

Thank you for your nice comment! It is very much appreciated!

@bryano6869 8 ай бұрын

Thanks for the great videos. Quick question. On the floating wine holder, the distance of the 1-1/4" hole should be 6-1/2" from the bottom of the board. Is there reason why you didn't design your jig to put the hole in that location? Instead of drilling it "upside down". I'm only asking so that the material above the hole can be any length and designed differently from one holder to another. Thanks again!

@jkmwoodworking 8 ай бұрын

Thanks! That's a great point, it would be a better jig to flip it around, so that you can make the length of different pieces different. The reason why I did it "upside down" is that I have a really small benchtop drill press, and it wouldn't have fit the other way. If you have a larger drill press than me, then doing it the way you suggest would be better I would think. I should have mentioned that in the video, thanks for the great question!

@bryano6869 8 ай бұрын

@@jkmwoodworking That makes perfect sense. I'll have to check if it will fit with my drill press. I doubt it as I have a small bench top press as well. Thanks!

@wendywhitman1918 Жыл бұрын

I’m brand new to woodworking and get a lot of useful info from watching your videos. Question- when you cut your 45 degree angles on the table saw- couldn’t you do that with your miter saw?

@jkmwoodworking Жыл бұрын

Yes, could have been done with the miter saw, but just that it didn't feel that safe with a short workpiece (10"), and 3 1/2" wide. If cut with a miter, it would have to stand on edge, or could have used the compound miter option to lay the saw down to 45 deg, both are possible ways to make the cut, but both just didn't feel right because of the short workpiece. Sometimes I'm probably over cautious, but just like to be safe and always feel comfortable. The table saw felt better/safer, and with the sled, then for sure it was. Thanks so much for watching my videos, I'm happy to hear they are useful!

@mattelias721 Жыл бұрын

Great video! Question: does the 45-degree end, 1-1/2" hole, and 6-1/2" distance of the hole work for any wine bottle (within reason)? I assume here that some in/out adjustment of the bottle depending on the shape might be needed.

@jkmwoodworking Жыл бұрын

Yes, it will work with most wine bottles. I tried it with all that I had (about 10) some different shapes, and it worked well with all. Note that the wine bottles I tested it with were roughly the same height bottle, so perhaps a very unusual height or shape might not work. Note that the hole diameter that works best is 1 1/4". Thanks so much for watching the video and the compliment, it is greatly appreciated!

@edhaskell1554 Жыл бұрын

Does your drill press table not tilt to 45 degrees?

@jkmwoodworking Жыл бұрын

It does tilt to 45, that would have been a good option also, great point! I just felt like the jig would be easier to setup and align each time I wanted to use it to make more of these in the future. Thanks for the comment, and thank you for watching the video!