Making a Lantern Style Tool Post

Рет қаралды 8,707

Күн бұрын

Hi. In this video I show you how I made a lantern style tool post. I wanted one of these tool posts so I could use a bunch of old style tool holders on my south bend lathe. The square tool holder that came with my lathe can't take these tools, they are too big. Having a lantern style tool post will allow me to use them. I gave up trying to buy one from an auction site because they are asking too much for what was available on the off chance that it might fit.
My next video should be a steady rest unless something else pops up, closely followed by a following rest. Regards.

Пікірлер: 60

@Akitene 10 ай бұрын

The concave washer is such a beautiful part. And I wasn't prepared for the matching convex support to be hand scraped. This lantern toolpost is beautiful. You did an excellent job, as usual.

@Thesheddweller 10 ай бұрын

Hi, thanks, I do try...😊 cheers

@mikebarton3218 10 ай бұрын

Very good work Paul. You achieve things that I wouldn’t know even where to start. Thanks for the video.

@Thesheddweller 10 ай бұрын

Hi, I sometimes have starting problems too. 😁

@robertorzech8922 4 ай бұрын

That's the exact tool holder post we had in our lathes in high school ! they were so easy to adjust the cutter any way you wanted and really fast ! Thanks for the memories !

@RustyInventions-wz6ir 4 ай бұрын

Nice work. Watched quite a few of your videos now and I do admire your skill.

@steved8038 10 ай бұрын

Lovely to see someone going back to old style tools, so much easier to use than replacement tips and usually a better finish.they weren't so daft those old timers .Thank you for a very interesting edition.

@Thesheddweller 10 ай бұрын

Hi, yes you're right, the only reason things changed, was manufacturing speed. Speed became the overriding factor in modern manufacturing. Thing is, in a little workshop like mine speed isn't important but, cost is. cheers

@robertpearson8798 2 ай бұрын

That wet tissue method is rather good, I’m going to have to give it a try.

@richardmeyer418 10 ай бұрын

That scollop you made looks beautiful. Congratulations.

@Thesheddweller 10 ай бұрын

Hi, thanks, cheers.

@braddobson2060 10 ай бұрын

Very good video and excellent work

@Thesheddweller 10 ай бұрын

Hi, thank you, I'm glad you enjoyed the video.

@Watchyn_Yarwood 10 ай бұрын

Very nice tool! I enjoy your narration almost as much as your machining!

@Dave.Wilson 10 ай бұрын

And the music, not!! 😊

@JamesP_TheShedShop 10 ай бұрын

Wonderful to see you in the shop Mr. Hopewell. Excellent tool making and machining.

@Thesheddweller 10 ай бұрын

Hi, thanks

@be007 10 ай бұрын

nice bild mr hopewell. cheers ben.

@Thesheddweller 10 ай бұрын

Hi, glad you enjoyed the video. cheers

@homemadetools 10 ай бұрын

Nice job. We shared this video on our homemade tools forum this week 😎

@lecnac855 10 ай бұрын

You just solved what I needed to know to make a tool post for my south bend 10 L. Thank you . .

@Thesheddweller 10 ай бұрын

you're very welcome. regards

@chrislee7817 10 ай бұрын

If you add a couple of pins, one in each end of the half moon section it will not fall out. Check the hardinge variant of these

@howder1951 10 ай бұрын

Great project, and lovely work all around. The first lathe I learned on had this type of tool holder, and it was very nice forking into tight areas, and simple house economical high speed steel cutters. I did like it better than the turret style which followed it after as it was so easy to get the cutter on centre rather than shimming. Got to love those sticky pins, I do see a lot of them on the amazing third world machines, fascinating. Enjoyed very much, cheers!

@Thesheddweller 10 ай бұрын

Hi, I've used all types of cutting processes and tools, from high speed steel to ceramic. High speed steel is still king for me, mind you ceramic gets close. These two techniques are different ends of the spectrum one is slow and will take off quite a bit of material, if it's asked. The other works at ballistic speeds and will only remove thin layers, but the finish is supreme. As for sticky pins they are still used in many machining environments where the operator is in charge of the set up, mostly on castings or fabricated parts. Regards.

@miketherefurbisher8000 9 ай бұрын

Fantastic content Paul!! "Thanks"

@zacharyschaafsma2523 10 ай бұрын

i literally just got done making one for my lathe . wish i would of watched this first

@Thesheddweller 10 ай бұрын

Hi, thanks for watching, I'm sure yours is perfectly adequate for your requirements. cheers

@alanremington8500 10 ай бұрын

Very nice !!

@Thesheddweller 10 ай бұрын

Hi, thank you.

@Rustinox 10 ай бұрын

I never made concave things. Maybe I should give it a go one day. Looks like fun to do.

@Thesheddweller 10 ай бұрын

Hi Michel. It was an interesting job and being an intermittent cut the swarf stings if it hits bare flesh. My next project is the steady rest and hopefully after that a following steady. cheers.

@HanstheTraffer 10 ай бұрын

Thanks for the very good explanation of every step. That is very helpful to us novices. By the way. They make ball cutters for the lathe that will reverse and cut concave cuts also. Not really that hard to make either.

@Thesheddweller 10 ай бұрын

Hi, thanks for watching, I know about ball or radius cutters and the capabilities, I have lots of projects on the go, what I really need is time cos I'm running out of that. cheers.

@andli461 10 ай бұрын

If you move the center of rotation for the boring head to the opposite side of the tilted rotary chuck, you should get a convex. If it’s a possibility irl due to interference between different tools, is another story though. The right mix between tilt angle and cutter radius may solve it. Don’t know the formula for that, but I’m sure there is one. Great project and execution! I like it. Especially the concave part. Clever!

@Thesheddweller 10 ай бұрын

Hi, Thanks for watching. Oh, there is definitely a formula for the milling combination to scallop out a radial arc or a spherical dish. Wikipedia is loaded with all sorts of formulas. cheers

@dermotkelly2289 10 ай бұрын

Lovely job mate. Well done

@Thesheddweller 10 ай бұрын

Hi, thank you. cheers.

@carlwilson1772 10 ай бұрын

Absolutely superb. A tour de force of your skill. The concave surface was especially good. The milling machine is truly a machine of applied geometry. I have a Harrison booklet on milling that shows the calculations etc for generating parabolics on the mill, with an application shown for telescope mirror manufacture. I have to say that I really need to find these boot sales/autojumbles/garage sales where you can buy milling cutters, lathe tools, metrology gear etc. Loved the film. And I enjoyed the calcs. I do like a calculation.

@Thesheddweller 10 ай бұрын

Hi thanks, there are geometric calculations for machining parabolic curves and spherical arcs on many machines. I used to cut spherical bearing bores for self aligning bearings on a twin ram boring machine, that was fun. The Staffordshire showground and the Newark Showground both hold a few auto jumbles every year they are a good source of used engineering tools .. you just have to take a van and lots of cash with you whenever you go. cheers

@carlwilson1772 10 ай бұрын

@@Thesheddweller Excellent stuff. The thing I like best about engineering is seeing calculations become real things. My problem with the boot sales etc is I am about as far removed from middle England, where they all take place, as it is possible to be, without being Norwegian. Not to worry. I manage well enough! Thanks again for a great film.

@jimsvideos7201 10 ай бұрын

I'll cop to being curious to make one of my own, with an adjustable parallel rather than the radiused bottom approach. Having the cutting force pressing more directly down onto the cross-slide just seems more efficient than having the tool cantilevered way out. Great video and great work on yours, if I try it myself I hope it'll come out equally well.

@Thesheddweller 10 ай бұрын

I'm sure it'll be fine it'll be interesting to see your take with the height adjustable washer. I had to stick to the old traditional tool post because, these tools I bought, are a little deep bodied, mind you I could have clamped them directly onto the compound slide, using two clamps through the tee slot but, I wanted to make something that was sort of traditional-ish. Regards.

@russrawley6712 10 ай бұрын

Really enjoy your Vids always look forward to them but I wondered why you didnt reduce the size of the flange on the post to save you breaking through on the "T" nut jusaying see ya next time Paul Russ

@Thesheddweller 10 ай бұрын

Hi, thanks for watching. I made the flange as big as I could, to grab as much as possible under the tee nut slot, the larger the flange the better the grip. The only limiting factor is the size of the tee nut slot. cheers

@leslieaustin151 10 ай бұрын

BSF on an American lathe? Isn’t that sacrilege? Oh well. A really nice project and the tool holder looks very firm. Was that a motorcycle steering tube getting the treatment at the end? I’ve had to fettle a couple of those lately. Greatly enjoyed the video, thank you. Les

@Thesheddweller 10 ай бұрын

Hi Les, it's not that bad surely, I wouldn't say sacrilege... after all, it wasn't metric. yes the tube was an old busted steering tube. glad you enjoyed. Cheers.

@robertpearson8798 2 ай бұрын

If you decide to start adding music I have a request…..Marcel Marceau’s greatest hits..

@Thesheddweller 2 ай бұрын

Hi, I’m afraid I can’t please everybody. Cheers

@robertpearson8798 2 ай бұрын

@@Thesheddweller I assume that you know that he was a Mime😉

@Thesheddweller 2 ай бұрын

@@robertpearson8798 yep

@EitriBrokkr 10 ай бұрын

What do you use for a scraper?

@Thesheddweller 10 ай бұрын

Hi, it is a 1 1/4" Tungsten Carbide tipped long handled scraper, I do also use an old file with a shaped end.

@JETHO321 10 ай бұрын

Ive watched mamy of the videos from the guys machining in Pakistan and they do some amazing work at times but i dont understand why everything they make has to make contact with the dirty floor, everytime.

@Thesheddweller 10 ай бұрын

Hi, yes the finished parts don't seem to get the respect they deserve. Hey ho that's the way they work, but it works. 👍

@nodriveknowitall702 10 ай бұрын

Got stuck at the math at 10:15. Had to do some algebra to understand what you were doing. You just figure that intuively or is that some common method for finding a radius?

@Thesheddweller 10 ай бұрын

Hi. that's a very good question, I'm not that intuitive but I must have used this simple formula many times in the past, I have it written down in an old (and decaying) note book. This note book I have, holds a jumble of calculations for many of my past working life problems. cheers.