Very clever!! been a toolmaker for 48 years never seen some of those set ups well done fantastic work....

Well Done! I hope you're more intelligent than to take any notice of the negative comments posted! Your home cast (so read FREE) blocks have enough depth to be plenty strong enough, especially for a mini lathe. You've shown insert tooling so once set up the tool holders probably will never come out of the blocks, how are the threads going to wear if they don't move? A bit of packing if needed to set the tool height, never to be set again if the same insert tool holder is left in the blook, just an insert change now and then. Two for one tool holder so halves the amout of Q/C tool holders needed, and far quicker and easier to machine new ones than all Q/C holders (from FREE home castings!!) when more are needed as your tooling collection grows. Far, far more ridged than most of the cheaper Q/C holders. Only suggestion would be a thick, large dia. steel washer under the post handle to save wear and tear when tightening them in place. Bloody well done again!! Colin

Really enjoyed the use of your lathe as a horizontal milling machine.

I've heard it said that anything you can do on a mill, you can do on a lathe. But I've never seen it in action. Great set ups going on there. I feel like you should do a video explaining your steps and decisions for fixturing.

Brilliant idea. I would never have thought of doing that. The tools are more rigidly held too.

Nice!!!! I love the look of machined aluminum and your craftsmanship is beautiful!!! 👍🏽😁👍🏽 two thumbs way up!

Fantastic love the milling /facing technique with tool held in chuck and casting your own blocks well done you sir

made some like this but out of steel (years ago) - hard to beat the performance per price - and made a set for 8 mm 10 mm and 12 mm tooling, didn't make an dedicated bore holder as of yet tho. The mild steel ones hold up remarkably well to time (and somewhat regular usage).

Several viewers already mentioned this, but I hope that my comment helps your video regarding the YT algorithm: I am impressed by your skills regarding milling operations on the lathe. Thumbs up to you!

Damn, lots of ways to mill stuff on the lathe, really nice!

That's a good idea! Everyone upgrades their toolpost to a quick change. I could probably hop on a forum and pick up a half dozen of these for little more than shipping cost.

A "slowish change tool post"... Brilliant! 👍😁

Very creative with the lathe. good work!

Beautifully done!

Beautiful. Work of art.

You have some great skills!

Wonderfull ! I have same mini lathe and your improvement is perfect ! 👍👍👍👍👍👍👍👍 from 🇲🇫

Nice work! Thanks for sharing this!

Man youre really confident on that 3 jaw chuck

Excelente trabajo MAESTRO, y muchas gracias por compartir tan buena idea , un saludo amigo ! ! ! .

work clean and executed with excellence, congratulations once again

This is so brilliant!

Interesting set ups!

You are very skillful, great job! Thanks for showing.

Interesting idea. Rather than buying (Or making) a quick change tool post and multiple holders, just make multiple tool post blocks, mount tools in them at the required height, and "Quick change" the whole thing as one unit. This setup's going to be a lot more ridged than those cheap Chinese quick change units, and almost as quick to swap tools (as there's no messing about setting tool height like when swapping bare tools). It also mounts the tool a lot closer to the post screw, so that's also going to help with rigidity. I could envisage semi finishing a batch of the blocks from a chunky length of bar, then cutting the tool slot as and when I buy new lathe tooling. My only reservation is the decision to go with alloy rather than steel. Aluminium's probably ridged enough not to flex in use, but I'd be worried about threads pulling out over time, and the post nut eating it's way into the body.

CLEVER!!!! Quick and effective!

Excelente trabajo, me gustó mucho, felicidades!!!

Nice idea. This toolpost don't loose rigidity, like conventional quick-change. It improve it)

Very well done!

Wildest fly cutter ever!

Great video thanks!

Interesting alternative 👍

Interesting to watch and very innovative.

Aye , well done mate great idea. U tube is plagued with stupid ideas / click bate but that’s a genuinely good solid idea and good creative use of the machinery / foundry work we all aspire to have and use at home. As previous commenters said any thread issues could easily be received / upgraded with “helicoils” or “keenserts” if there were ever any issues ( hey silly point did you know 55 degree whitworth is regarded as the strongest thread form , particularly in soft materials ? ) But aye absolutely fantastic mate , really like your tool post and the creative ways which you created it 👍🏻

Nice work.

very nice work. thank you for sharing

Brilliant!!

great job. amazing

Beats cutting dovetails, great ideal.

Erinnert mich immer an meine Zeit in Südafrika

Very good idea! I was going to make one single 4-way, but this is a better idea! I’ll make 3 or 5 at once. Especially one for my boring bar!👍😃 One might add an indexing disc, much like the raising disc you used when milling, and that way also repeat tool angle. (A feature one doesn’t have on a fourway, so not really that necessary.) This is excellent cheap hobby tooling!

Nice work, were did you get the block with T Slots

So good to watch 🤓

Sooo brilliant!!! Please can you tell me were to find the holder you are using from 4;37? Thanks

Ótimo serviço,parabéns.

So first I see this old Tony using his milling machine as a lathe and then this :)

So simple and rigid. I would made one of these from steel for extra strength.

Beautiful

Excelente, muy bueno.

seems to be more rigid than usual quick change tool posts, do you have a way to index it for repeatability?

Excellent work .

With carbide inserts, there is no need for an adjustable height of the cutting tool which was necessary when you sharpened yourself the tool. I have done exactly the same on my EMCO Compact5

Great work and clever use of milling tools in the lathe, but did you really save much over just buying a normal steel quick change post? Or was it just done as a useful exercise? Nice job with the ali casting too.

Brilliant

This is actiali very good,

Are you using 10mm tools? I have 8mm standard tools, and was looking at upgrading to 10mm Carbide tip tools. Just want to make sure this is a good option

Interesting, I still prefer a regular QCTP because it keeps its orientation, even when you swap a holder out. It's also pretty repeatable and if you keep track of your tool offsets, you don't have to dial in a lot. On your version the tools will always end up in an arbitrary orientation unless you dial it in, which takes too much time for it to be useful. Also not every tool has the cutting edge on the same height, it's better if you can adjust it easily.

Nice work but 0:23! I get it is a small lathe but that move is going to bite sometime.

It works. But is it an improvement? After grinding the tool may need height adjustment. One may have different size tool bits requiring different heights. A QCTP is quicker, surprise. If you have no casting facility a $10 tool holder is cheaper than the Al stock to make them.

Amazing job. Is there anything you can't do with a mini lathe?

Perfeito!!

Leaving aside the suitability of aluminium, there is a major issue with this design- there is no positional location of the tool-block, so you loose registration every time you remove the tool. With conventional QC tool holders you can rely on your DRO when you replace the same tool- a major feature.

Who needs a mill when you have a lathe.

Nice clean design, my only concern would be getting enough purchase on the tool clamps without stripping the threads in the aluminium. You could counter some of this by Helicoiling the threads. Good video, I sold my mini lathe a couple of years ago when I bought my big one but before I did I made all sorts of stuff for it - its a good cheap way to teach yourself machining skills.

What ingredients are you cooking?

Mantap bos ku. Berapa harga mesin bubut nya

Show em my friend s.brasil

How much the mini lathe?

Please inform the address of the official distributor in *Indonesia* ...

Interesting. We shared this video on our homemade tools forum this week :)

Good ideas and machining, but please loose the long sleeve shirt and do not leave the T-handle in the spindle chuck.

Home casting well worth doing. A chunk of ALLY that big would cost a few quid here in the uk.

As Spock would say: "Fascinating" Very clever idea man! What did you use the round stock for that you milled flat on the one side?

Don't understand how you secure the right positioning after changing the tool holder. I use Multifix on my lathe with electronic leadscrew.

Way cool dun care what anyone says.

SPETTACOLOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO

С комментами, конечно, было веселее... Но все всё понимают...

👍

how to cast aluminum without pores?

real tired now, hafta lay dwn now.

I didnt understand what is alternative in this product? İt is same, just dimension changed...

Hanzhen harmonic gear , strain wave reducer, robot arm gear , over 30 years experience

Well done, I can appreciate the creative setups. But I must say, you really goofed with the hacksawing on the lathe with your long sleeve and glove on. Also, please, for the love of god always take out the chuck key. it is a small lathe and probably won't kill you, but you continue working like this, you will be injured sooner or later.

I prefer my 4-way tool post to those quick change holders for most lathe work. The tool holders made in this video would be absolutely useless to me since those holders do not index.

What is that part that you put at 4:36?

👏👏👏👏👏👏👏👏👍👍👍👍👍😁😁😁😁😁

never clicked on mounting the cutter in the chuck ,im so rusty at this,havnt had a lathe for decades

Did you learn to use the lathe by yourself??

прикольно, но квик-чейндж это немного другое ) тут же просто поворотный резцедержатель.

If you hadn't used a quick change tool post as part of the process to make a new tool post, I'd give you full marks for ingenuity! :P

Один я думаю, что резцедержки изготовлены не из самолейки, а из чего то типа Д16Т ? :)

Good job but for the price of quick change holders nowadays I think you'd be working for less than minimum wage building them.

What is the point - its standard multi position tool post that many cheap lathes come with standard for past 20 years!

turret

Most people have the two cutting tools they use the most set up on a normal holder . If you need a quick change you should have got a bigger more industrial lathe with the extra tools and features at the start .

Remove compound rest slide, replace it with block of steel.

Don't leave the key in the chuck, mate. You are one accidental button push from a dangerous situation.

First, I like the design, second, I love how versatile you are on a lathe. But, are your designs relying on your measuring to center the cutter height!? Now I understand that there have been trillions of miles of precision turning on old Lanterns, but you appear (correct me if I'm missing something) to have precision milled your tool slots "tool specific" to a pretty tight tolerance without the ability to adjust for cutter offset. The shot you showed the cutter tip "on center" would change with one grinding. Unless these are all replaceable, indexable carbide carbide inserts. Even then, you better buy "good ones" because they need to all be IDENTICAL! Help me out here...

There is a reason they don't make aluminum tool holders. Smdh

😂